My advice. Don't buy cover panels in the "as is" section as they are not always properly labelled. I would say the cover panels and fillers are the hardest part of an ikea kitchen. And I also learned the hard way that different cover panels for different purposes are different thicknesses!!! and white isn't really white - ugh - IKEA!!!
@uptokode4 жыл бұрын
You’re absolutely right about the fillers being the hardest part of the install. Sometimes the learning curve is frustrating...trust me I know. I don’t think I’ve ever been clear of the learning curve.
@jcolby31824 жыл бұрын
Whats the best blade for your table saw if you're ripping these panels down?
@lancecrane103 жыл бұрын
did you ever find an answer to this question
@tanvirgrewal10393 жыл бұрын
60 or 80 tooth blade. Anything smaller than 10 inches I think 60 tooth is the only option. But they do the job.
@prairiejolene5 жыл бұрын
Question about the side panels....can they be cut down to make a door? If so, what do you recommend to finish the cut side so the bare wood isn't showing? (PS. my kitchen is pretty much the exact same set up the one you did here) Background - we had a 7" gap on each side of our stove and since Ikea doesn't do anything this small and the staff in the kitchen planning dept didn't have any solution other then cover it up with a cover panel (too much wasted space for my liking), we bought Rev-a-shelf filler pullouts that I thought were 5" wide (no idea now why I thought that) but are actually 6" wide. Our initial plan was to mount a drawer front (5" wide) as the doors for these pull outs but, of course, now we realize I was wrong on the size and they won't work. My hubby with his "we'll figure it out later" attitude has already installed them and installation included screwing into them so they can't be returned now. I asked a cabinet maker if they can make a door for them and was told that they can but they won't be able to match the color and sheen of the Ikea ones. Her only other suggestion was to use the bigger drawer front and cut the middle of it out and glue them together. There would be a seam down the middle though so that would look awful.
@uptokode5 жыл бұрын
Definitely into tricky territory but it can all be done. I’ve cut panels into all sorts of things. Here are some options for you. 1. Cut 2 panels to make 1 door. Make it so the seam is in the middle so the factories edges run around the perimeter of your new door. 2. Make your own door out of MDF and get the paint color and sheen matched as best as possible. 3. Simply but a panel down to your door size. Either paint match and paint the 1 edge. You could edge tape it with maple edge tape so the paint looks better. In the end whatever you think is least noticeable. Hope that helps.
@dawno2608 Жыл бұрын
Thank you! Needed this video! Lol 😂
@uptokode Жыл бұрын
Glad it was helpful!
@Realism914 жыл бұрын
I too disliked Phillips fasteners, then I found a different Phillips bit, PR2 they fit like a glove and actually grip a Phillips, way less slipping.
@PeterSz733 жыл бұрын
It is called pozidriv or pozidrive and it is PZ2 designation. Most all sektion cabinet screws are PZ2!!!
@andrewdenine16853 жыл бұрын
Little #6 wood screws work great and their Robertson much better. Thanks for this video I'm installing cabnits for a customer now it's my first time installing these they are definitely a lot of work . Still cheaper but nothing cheap about install cost. They are turning out to be custom cabnits by the time I'm done
@T00ms1 Жыл бұрын
If you had a larger island (72x48) with two rows of cabs back to back, which panels would you use to cover the 48" sides?
@uptokode Жыл бұрын
Probably the 36” x 96” panel. Or the 26x36 with extra joints.
@johns51275 жыл бұрын
Can you paint any blemishes on white end panels??? Both of my 36×96 panels were banged up especially the corners.
@brianmcdowell80214 жыл бұрын
Yeah, but it's particle board so may not hold well without some prep
@yudel3899 Жыл бұрын
Do I necessarily have to use those cover panels?
@uptokode Жыл бұрын
Not at all. There are companies that make custom fronts and panels to match the ikea system. Or feel free to use your own material and finish it anyway you like.
@Eddie-gb3bn Жыл бұрын
For those 30x32 upper side panels, what if you have backsplash that goes all the way up to the bottom of the upper cabinets? How can you have that valence in the bottom when you don't have enough material to scribe to the wall? Is there any other panel that'll give me an extra inch on the width to be able to scribe to the wall and still have enough to be flush to the cabinet doors.
@uptokode Жыл бұрын
I don’t recall a panel that size. Sorry.
@uptokode Жыл бұрын
They make a 26x36 dishwasher panel or a 36”x96” panel. Those will work for you.
@brianlocal32 жыл бұрын
Silly question but what length screw are you using to attach the cover panels?
@uptokode2 жыл бұрын
I use a type 17 screw. Size #8 and 1 1/8” long. Special order. You can also use the screws they provide.
@manueldignard7842 Жыл бұрын
Where do you find the 1 1/8th screws?
@uptokode Жыл бұрын
I order them from a fastener store. One who is specific to screws and/or bolts. They are a specialty item. Or get the proper bit for the ikea head (I forget the name) and the ones they supply will work
@dilligaf23863 жыл бұрын
Do the end panels come deeper incase I have to pack the wall unit out from 5mm so if the wall unit is 250mm deep and I've had to pack the unit out from the wall 5mm then the end panel needs to be 255mm
@uptokode3 жыл бұрын
You can use a dishwasher panel for the sides. They are 26” x 36”. They also make a giant panel that is 36” x 96”. Sorry I don’t know the metric version.
@dilligaf23863 жыл бұрын
@@uptokode that's great thanx. So they still use inches over there then.
@uptokode3 жыл бұрын
Yes we still do. Don’t ask why. Old habits I guess
@danlarkin24154 жыл бұрын
On a corner cabinet, how do you cover the gap where the cabinet meets the underside corner?
@peterm51322 жыл бұрын
Question: for the bottom cabinets, do you need to install panels between the stove/dishwasher and the cabinets? Or can the cabinets butt up against the stove/dishwasher?
@uptokode2 жыл бұрын
You don’t need panels beside the stove or dishwasher. Both appliances can sit beside the cabinet box.
@jillianlinn26763 жыл бұрын
HI Kody, is there a way to centre your sink on the window when the cabinets don't line up? The centre of our windows is 60.5 inches from the corner. With the 2 corner cabinets available the centre of the sink ends up either too far to the left or right. Any solution for that?
@uptokode3 жыл бұрын
The lineal corner cabinet (47” long and 24” deep) won’t work unless you install a 9” wine rack between it and the sink cabinet and then fill the odd sized space. Or use the 38” x 38” lazy Susan corner with a 18” cabinet, then a filler and then the sink cabinet. Either way you need a filler.
@frietjesate62882 жыл бұрын
Hi Kody, great videos, helped me a lot with installing the kitchen. I have a question though. When cutting cover panels for lower cabinets to size, i see you put the finished side at the bottom. Is this necessary or preference? My cover panels are made of MDF, and i worry about moisture. Are the panels treated in any way? I thought about painting the trimmed edges, but it’s a bit of a hassle. Mark
@uptokode2 жыл бұрын
I try to put the factory edge against the floor to prevent any moisture wicking into the MDF. If you do need to put a cut side down, then yes seal it with primer at least. Silicone afterwards if in high risk water area.
@micuzzu2 жыл бұрын
where do you get those 1-1/8" screws?
@uptokode Жыл бұрын
Special order from a fastener specialty store.
@jpretzel2 жыл бұрын
Does each panel have the coating/paint in all 4 edges?
@uptokode2 жыл бұрын
Yes. Technically all 6 sides. 😛
@riffmeisterkl2 жыл бұрын
I have an ikea high cabinet 2m tall (80”). Would I be able to hang this flush to the bottom of the cabinet, without touching the floor? the cabinet is sitting on the feet. Not sure if it can suspended screwed into the cabinet because of the weight? Or just use more screws ?
@uptokode2 жыл бұрын
I’m not clear on the question. Do you want to suspend the 80” cabinet? How wide is it?
@uptokode2 жыл бұрын
Just in case I don’t see your response to my question. If I was suspending a large cabinet like this. I would obviously use the top rail. But I would also use more of the IKEA L-brackets and customize a way to have 2 more (1 on each side) about 2/3 of the way near the top. I would probably use 2 more near the bottom. Those cabinets can hold a ton of weight so it’s best to add extra security
@riffmeisterkl2 жыл бұрын
Hi, what I meant is the cover panel for the high cabinet. I’ve since suspended the cover panel off the ground by screwing it flush to the side of the cabinet. Wasn’t sure if those screws good take the weight of the cover panel. But I just ended up using more acres.
@uptokode2 жыл бұрын
You’re totally good !
@ivettesiguenza97195 жыл бұрын
Im in a pickle I have to install a dish drawer dishwasher that is 17 7/8 x 23 13/16, and I was thinking in modifying a 24" regular base cabinet also, can you do a video how to wrap around a counter depth fridge i have a 90" pantry and im planning to put my 24" w x 74 1/2 H counter depth fridge beside it. then is a wall, so I want to put a cabinet in top as you did that wont be flush it will be same depth as the fridge so ill look like built in, help!
@uptokode5 жыл бұрын
For the dishwasher you could modify that by cutting into some drawer fronts or other combination of panel so you have finished edges on the outer perimeter and cut edges where the DW slides into. I think this one relatively simple, just takes some ingenuity. The fridge I would need to see a sketch in order to help with that issue.
@jebusfreek6667 Жыл бұрын
Can the filler panels be held with just construction adhesive? I would prefer not to nail through them as I am getting matte black and think nail holes would be really obvious and very difficult to fill. I will be gap filling 2.5" from a high cab. to the wall. on both ends of the run.
@tanzinaahmed70024 жыл бұрын
Can you use the Ikea system to cover the fridge doors so they blend in with the cabinets. I’m looking for the seamless look and wanted the appliance to be paneled. Thank you
@uptokode4 жыл бұрын
You might have to get creative on making the panels a specific size to suite the fridge or appliances. I know they make it possible for a dishwasher
@danwilliams5822 жыл бұрын
Kody, thanks so much for your videos on Ikea kitchen installs, they have helped me out a lot!
@uptokode2 жыл бұрын
You’re welcome
@svilenkonac48174 жыл бұрын
Hi Kody ! Can i use 25x90 cover panel on a side of fridge cabinet? Other side would be attached to 24 in deep high cabinet . Fridge is 33 in deep so it will stick out a bit , but no big deal.
@JohnSmith-xx9se3 жыл бұрын
Also wondering about this. Bummer he didn't reply.
@svilenkonac48173 жыл бұрын
@@JohnSmith-xx9se I did it , came out perfect.
@svilenkonac48173 жыл бұрын
@@JohnSmith-xx9se what's your e-mail, I'll send you a photo if you want to visualize it.
@robertromans7584 Жыл бұрын
Kody, why do you use only 11/16 thick panels for islands? Do you recommend against using 1/2”? If so, why
@APJardine3 жыл бұрын
Suggest the reason you dont like the Ikea screws is that they are posi-drive not philips # 2
@uptokode3 жыл бұрын
That’s exactly it!
@tomatojuice122 жыл бұрын
Hi Kody! Thank you for these wonderful videos. I am building an Ikea island with SEKTION base cabs - 15" + 36" + 24" widths (total 75") Ringhult. Would you buy a 36" x 96" cover panel for the back (and cut twice) or would you buy 3 panels 25" by 30" and not cut at all? Do the lines show if I go with the 3 x 25" by 30" route? Thank you!
@mtc-tech Жыл бұрын
How did you secure your long frig panel to the ground?
@skyhighkite31234 жыл бұрын
great info! trying to figure out panel depth dimensions to make diy panels out of birch plywood. how far do the cabinets sit off wall due to the suspension rail +1/4"? what is the actual depth of ikea wall and base cabinets, 15 & 24"? Add 3/4" to flush out with doors? Assuming walls are plumb what is the actual depth dimension for both wall (16" wall and 25" base? thank you for your help!
@BZ13404 жыл бұрын
I liked this video and was quite helpful. I need to build a post cap out of the Erasdum material. Any thoughts. It’s a 4 sided cap separated by a countertop in the middle Of it. Both approx. 40 inches tall. I’m trying to make it look like it continues thru the quartz top. It’s a 6x6 finished look. I thought of 2 box’s with a U and then fill it with a filler after sliding it on. But the finished edges have me concerned on the 90’s.
@Boinzy4764 жыл бұрын
IKEA sold me 24x30 doors to use as end panels for my island and one wall cab end. It's a little bit wider than than the cabinet. Where do I put the flush end? On the back overhanging the front a little bit to cover the sides of the doors or drawer fronts? Or flush to the front of the cabinet covering the gap at the back?
@iknownotseems2 жыл бұрын
Can you link those panel videos you mentioned. The shorter ones on how to do what you already prepped. ?
@MuchoJimbocho7 ай бұрын
Video is helpful. One issue is that many (most) countries in the world use metric measurements... which would be useful to have in a screen subtitle.
@uptokode7 ай бұрын
Very good idea. And yes you’re right most counties are metric. Silly me
@lianaaires7052 Жыл бұрын
Your videos are so helpful. Thank you so much!
@matney124 жыл бұрын
Does it look better to use a side panel on both sides of the stove and the microwave cabinet above? This is if you are not expanding the size like the video.
@lori94235 жыл бұрын
Great videos thanks
@uptokode5 жыл бұрын
You’re welcome
@jumpa572 ай бұрын
Great Video! Thanks for the effort
@uptokode2 ай бұрын
Appreciate the comment.
@cascajohn663 жыл бұрын
great tips
@uptokode3 жыл бұрын
Thank you
@cascajohn663 жыл бұрын
@@uptokode I am building an ikea kitchen now and have learned a lot from your tips
@garytaylor99043 жыл бұрын
Can you do mm please
@TheSholon2 жыл бұрын
Hi Kody, really great work, your videos have helped me out a lot! I have 9ft ceilings in my kitchen and we wanted to put cabinets all the way to the top. I can't find any 9ft panels on Ikea's website, the tallest one I see is 8ft. Any recommendations on how to tackle this problem? Should we just cut 2 panels (1ft and 8ft)?
@uptokode2 жыл бұрын
8’ panel is the longest. One of my more recent island videos shows how well I can do a butt joint. So yes do a 8’ & 1’ but I would probably do a 7’ & 2’. Your call.
@uptokode2 жыл бұрын
Custom Ikea Island, No Trim & No Shortcuts! kzbin.info/www/bejne/aGarl3aspdt8aMk
@mikelang98283 жыл бұрын
Love your videos!. can you advise what you'd do with my island? I have 24" cabinets backed up against 15" cabs. there are no panels that are about that width, meaning I'd need to cut some off- but I dont want to cut any off and see the malamine interior of the panel on one of the ends. Any thoughts?
@uptokode3 жыл бұрын
I would cut 2 panels and have the cut joint meet in the middle somewhere. Factory edges where doors/drawers are. You have to have deadly cuts but I have done it before. It’s that or depending on the finish either paint match and install your own MDF panel OR a piece of veneer plywood stain matched to the rest of the kitchen. This 2nd takes more work obviously.
@mikelang91933 жыл бұрын
@@uptokode you’re the man! You’ve given myself and my dad who’s also redoing his kitchen lots of tips and tricks even though this is my 2nd ikea kitchen. If you’re ever wanting to expand into the Edmonton region I’m your man!
@uptokode3 жыл бұрын
Thanks Mike! Make sure to email me finished photos and I’ll make a “fan feature” video of folks like yourself and your project