IKEA TV wall unit by Besta | Complete Installation of TV wall mount Easy| Safety Issue resolved DIY

[@pe2062]

Thank you so much for this video! I was stuck when trying to thread the small square back panel to the unit via the two plastic liners. Then really confused as to why the unit didn't come with mounting rails. All my questions answered, after hours of struggle, in 26 mins. You are a genius sir.

[@TowneBlvdTiy]

Hi there, Thanks for the heart felt feedback. When you make a video and put it out there you never know what the impact will be. It makes me happy that my video was able to help. 😄👍🏾

[@izopen]

Watching this at 2am in the morning ready to bounce from my bed and fit this TV cabinet to the wall. Thanks for showing the whole video on how to mount this to the wall fella 🔥 🔥 🔥

[@TowneBlvdTiy]

Hi there, Thanks for watching my video, really appreciate the positive feedback dude👍🏾😃

[@michaelragan6898]

Dude, thank you. I almost didn't buy this because of all the reviews complaining about stud spacing.

[@TowneBlvdTiy]

Hi there, Thanks for watching my video and the suburb feedback. You are very welcome. I'm sure you will enjoy this unit once it's in place. Good luck 🤞🏾 Thanks again for watching my video and the subport to help me grow my channel 🙂

[@cpett1]

This is the most detailed video on the Web & I thank you for sharing it wilt us who are struggling to make sure that it secures to our walls safely!

[@TowneBlvdTiy]

Hi there, Thanks for the heart felt feedback. When you make a video and put it out there you never know what the impact will be. It makes me happy that my video was able to help. 😄👍🏾 Thanks for watching my video and the subport to help me grow my channel.

[@FranciscoGonzalez-qe7rm]

I couldn’t stop free styling with this beat 🔥🔥

[@mstockton9364]

Thanks for sharing this with us ! tbh though…with supports repositioned in that manner it would seem that the entire weight of the cabinet is still only going to be supported by the pins and dowels in the top panel as the support brackets only make contact at the point… vs mounted to the inner side panels which in turn supports the top panel and the shelves. If not using rail (which has ability to hit the studs), probably best to use strongest drywall anchoring system available AND consider mounting additional support bracket(s) lower down on the inner side panels for added security. JMHO…..maybe I’m wrong.

[@TowneBlvdTiy]

Hi there, Thanks for watching my video and the ultra-kind feedback. That's for sharing your several ideas. However, would not recommend doing anything with drywall only. The wall mount that I installed years ago is still as strong today. There are no issues with support yet. Thanks again for watching and the subport to help me grow my channel👍🏾

[@edenmavity2823]

Super helpful! The only video that actually shows the full install. Thank you! Looks great, I love the colour choice.

[@TowneBlvdTiy]

Hi there, Thanks for watching my video. I appreciate the positive feedback. Yes, the color choice works well with the basement floor also. 👍🏾😄

[@scotthill4075]

Hi, I know it's been a long time since you installed the unit. Did you use the screws that originally came with the brackets when relocating them or different screws? Did the brackets attached to the until well? Great idea btw I didn't think to move the brackets thank you.

[@TowneBlvdTiy]

@@scotthill4075 Hi there, thanks for watching my video and the feedback. I was able to use the original screws for the Top of the bracket that screwed into the unit But I used slightly longer screws (about 3") that I found on my own to secure the other side of the bracket to the wall studs. You can verify the length by tapping into the wall stud with your drill as a slight pre-drill hole. I did want to take any chances. The brackets attached well. It's still in place. Hopefully that helps. Thanks again for watching and the subport to help grow my channel 👍🏾 😀

[@ianirwin1237]

Hi sir, This is a great video. I apparently have this BESTA cabinet, which is the "older" version. On these types, you have to use the metal brackets. This video helped me so much, because I was given the cabinet for free, but the metal brackets were missing... Now I know which ones I need. I was just wondering, I'm going to be attaching this to concrete, so will use the direct screw method. Only problem is the cabinet is assembled and I will need to install the brackets after purchase. Do you think it is possible to install the brackets after the cabinet is assembled? How many are needed? Thanks again

[@TowneBlvdTiy]

Hi there, Thanks for watching my video and the ultra-kind feedback. When I make a video and put it out there I never know what the impact will be. O'boy sounds like you have some challenges ahead of you after been gifted a free gift. I'm not familiar with the brackets at all, but I'm sure there videos on KZbin that will hopefully show you how to use them. My initial concern would be the concrete wall that you will be attempting to attach the unit to. You will need a masionary concrete drill bit and the right size concrete screws to be safe. Installing the bracket after the cabinet has been assembled may also be problematic as you my need to get into some tight spaces to work with the bracket(s). Keep doing your research and asking questions. Let me know how you make out. Thanks again for watching and the subport to help me grow my channel👍🏾

[@danielag7092]

Hi, thank you so much for your video! What kind of wall screws did you use? I see you mentioned in your video that the wall screws are not included. I am very nervous to put this together. Thank you!

[@danielag7092]

Any specific recommendation for the screws and plugs?

[@TowneBlvdTiy]

Hi there, thanks for watching my video and the kind feedback. I was able to use the original screws for the Top of the bracket that screwed into the unit But I used slightly longer screws (about 3") that I found on my own to secure the other side of the bracket to the wall studs. You can verify the length by tapping into the wall stud with your drill as a slight pre-drill hole. I did want to take any chances. Hopefully that helps. Thanks again for watching and the subport to help grow my channel 👍🏾 😀

[@TowneBlvdTiy]

@@danielag7092 I would not do plugs, the unit is too heavy , the studs is the best and safest approach.

[@db0nn3r]

Solid man. Thank you for this. Moving the brackets to stud locations is key. Didn’t think of it lol.

[@TowneBlvdTiy]

Hi there, Thanks for watching my video. I appreciate the positive feedback. Yes, I had my suspicion of the IKEA instructions. They need to step on this up before someone gets hurt. Thanks for watching and the support to grow my channel👍🏾😄

[@HypocritesExposd]

Am about to do this same install/bracket stud modification, so seeing you do it first really helps! Thank you and wish me luck!

[@TowneBlvdTiy]

Hi there thanks for watching my video 😁 Good luck sir with your project 👍🏾

[@travist603]

Thanks! Just got one of these and I'm glad I don't have rely on only ikea's instructions :)

[@TowneBlvdTiy]

Hi there, Thanks for watching my video and the feedback. No problem if you relied solely on the IKEA instructions You surely would have been in trouble with a damage floor and a busted unit. Good luck with the project. 😄👍🏾

[@abhayarora3836]

Hello. Thanks for the video. What if i am unable to locate studs in the corners where the stand needs to be? I understand that the middle ones can be moved. But what about the ones on the each corner?

[@TowneBlvdTiy]

Hi there, Thanks for watching my video and the feedback. Studs in the corners are more difficult to locate and use because of the tight space. If understand correctly, the studs are not necessarily on the ends of the unit. I would seek out the ones in the middle that are 16 inches apart in range. Hopefully that helps. Thanks again for watching and the subport to help me grow my channel👍🏾

[@abhayarora3836]

Understood. But how would corners rest on drywall initially without the screws going in the stud? Are you using anchors in the corners?

[@abhayarora3836]

Or at 16:45 do you say that the unit will stay without studs for the time being on the corner screws until we find the stud for middle ones.

[@TowneBlvdTiy]

@@abhayarora3836 I would say you are taking your choices. This is a very heavy unit and will eventually pull out the plug/anchors that are used and come crashing to the floor. It would only be a matter of time.😭 You would better be served to spend the time and find the studs and adjust the screws to anchor to them. Better safe than sorry 😔

[@abhayarora3836]

Oh. I think i didnt frame my sentence correctly. Studs will be for middle two brackets. I have already located and marked them. . I am just concerned where will the corner brackets fix themselves.

[@UnknownMike89]

Thank you for this sir, I am planning to get it and i was confused little but by the system of hanging it.

[@TowneBlvdTiy]

Hi there, Thanks for the feedback. IKEA has instructions but if you follow them to the letter your unit will come crashing to the ground in a matter of mere minutes. IKEA needs to look at this part of their wall mount instructions. You need to locate your wall studs and attach the unit to those. Thanks for watching my video and the subport to help me grow my channel😄👍🏾

[@UnknownMike89]

@@TowneBlvdTiy Yes!! Thats why i was so confused by them!

[@Milehi6h]

Amazing video. Thanks so much for outlining your modifications. Huge help!

[@TowneBlvdTiy]

Hi there, Thanks for watching my video and the kind feedback. Feedback like yours is inspiring and much appreciated. Thanks again for watching my video and the subport to help me grow my channel👍🏾

[@terryyouth]

good job and neatly done. few things i would suggest is do not tighten the screws fully straight up, screw in bit by bit all screws- this ensures that it is nice and flush and not pulling. also the release latch, would be best to fix where you expect to push it like at 24.11

[@TowneBlvdTiy]

Hi there, Thanks for watching my video and the ultra-kind feedback. Feedback like yours is beneficial not only to me but all that reads these comments on these videos😄 Thanks again for watching and the subport to help me grow my channel👍🏾

[@terryyouth]

@@TowneBlvdTiytime to now hang up the cabinet. Was not sure if I had all the bits. I plan to attach a timber across the studs and then fix the cabinet to the timber. I bought the glass top as well. I guess it will not blend in. But thanks for your video I can now think of something

[@omaryacuoby5907]

What kind of screws did you use for the studs? Thank you

[@TowneBlvdTiy]

Hi there, thanks for watching my video and the feedback. I was able to use the original screws for the Top of the bracket that screwed into the unit But I used slightly longer screws (about 3") that I found on my own to secure the other side of the bracket to the wall studs. You can verify the length by tapping into the wall stud with your drill as a slight pre-drill hole. You would need to predrill the holes anyways to make it easier to drill into the studs. Hopefully that helps. Thanks again for watching and the subport to help grow my channel 👍🏾 😀

[@omaryacuoby5907]

Thank you so much for thr quick response. I appreciate your page.

[@crystalmaze3646]

Is that stable enough with those metal screws no metal strip to sit against

[@TowneBlvdTiy]

@crystalmaze3646 Hi there, Thanks for watching my video and the questions. Hi, Yes I was able to use the original screws for the Top of the bracket that screwed into the unit But I used slightly longer screws I found on my own to secure the other of the bracket to the wall studs. You can verify the length by tapping into the wall stud with your drill as a slight pre-drill hole. I did want to take any chances. There was no metal strap involved. Hopefully that helps🙂 Thanks again for watching and the subport to help me grow my channel 👍🏾

[@lovebertierose]

Great video. Can you tell me what bits you used in your video? I would love to do this with a drill than the little tools they pack.

[@TowneBlvdTiy]

Hi there thanks for watching my video and the question. The bit is called a Phillips-head, has a slot in it's top that looks like a cross. Sometimes they come in 3 sizes, small, medium, large. I used the medium bit. However, If you are buying a varity screw driver bit set, then you should be o.k with other bits you may need. Good Luck😄 👍🏾

[@lovebertierose]

@@TowneBlvdTiy Oh good, so they are just the Phillips head bits. I thought they were a different size. I have Philips so great. Thanks for the video and fast response.

[@TowneBlvdTiy]

@@lovebertierose Hi there, no problem!

[@neeshajoshi1432]

Thank you for this!! We were thinking of doing this but weren’t sure if it would work. Really appreciate this video. IKEA definitely needs to make a modification

[@TowneBlvdTiy]

Hi, no problem. Hopefully your installation is safe and rewarding 👍🏾

[@LukeSimpson]

Thanks for this, I’ve seen multiple other Besta wall mount install videos where the back of the units look completely different and they use the Besta suspension rails. No idea why some Bestas are different in back, but I got one that looks like yours, so I guess I’ll have to follow what you did with the mod to hit the studs.

[@TowneBlvdTiy]

Hi there, Thanks for watching my video and the kind feedback . Yes, don't know either, the studs is the best way to go with this unit. Hopefully your installation is safe and rewarding. Thanks for watching and the support to grow my channel 😀👍🏾

[@LukeSimpson]

@ImagineNation I bought suspension rails when I bought the unit but the unit I bought did not have anything that the suspension rails fit onto.

[@angelicavargas1998]

Omg thank you sooooooo much I was having trouble with matching the position of the hole with my studs it was impossible! Until I seen your video 🙌🏽🙌🏽🙌🏽

[@TowneBlvdTiy]

Hi there, Thanks for the heart felt feedback. When you make a video and put it out there you never know what the impact will be. It makes me happy that my video was able to help. 😄👍🏾

[@dwightk.schruteiii8454]

So basically the metal brackets have to go to the studs? I don’t have to buy the metal rail?

[@TowneBlvdTiy]

Hi there, Thanks for watching my video and the feedback. Yes, you can use the metal brackets provided, but you will need longer screws that will reach into the studs. Hopefully that helps. Thanks again for watching and the subport to help me grow my channel👍🏾

[@dwightk.schruteiii8454]

@@TowneBlvdTiy thanks! Are the screws provided in the kit not long enough?

[@TowneBlvdTiy]

@@dwightk.schruteiii8454 I used slightly longer ones to make sure. You should be able to tell once you tap into the studs how much extra room there is until it's all tigh Hopefully that helps👍🏾

[@dwightk.schruteiii8454]

@@TowneBlvdTiy very nice thank you!

[@carlosesquivel3050]

I waited for IKEA to finally send me the suspension rail and it was crap. I'm using your method!

[@TowneBlvdTiy]

He there, Thanks for watching my video and the feedback. Lol, glad my fix was a better option than the IKEA suspension solution. Good luck with your TIY project 👍🏾🤣

[@StephenJBeard]

This was super-helpful, especially on your mod with the studs. Thanks for putting this together!

[@TowneBlvdTiy]

Hi there, Thanks for the heart felt feedback. When you make a video and put it out there you never know what the impact will be. Yes, IKEA needs to look at this part of their wall mount I instructions. Thanks for watching my video and the support to help me grow my channel😄👍🏾

[@saitejagatadi9711]

Bro, In my case it is brick wall, Do I need to use french cleats (2) and hang it on them and then screw it in 4 metal brackets (provided by IKEA) Or Can I directly use 4 big screws to hang it on wall.. Which choice would be better 😀

[@TowneBlvdTiy]

Hey dude, I would go for the direct screw attachment method. I'm not familiar the metal brackets. Make sure screws are long enough and you do some pre-drill of the holes. Hopefully that helps.

[@janicedizon1129]

Hello! Thanks for this video. Really helpful. So,you didnt use the suspension rail they recommend?

[@TowneBlvdTiy]

Hi there, thanks for watching my video and thanks for the question. No, I did not use a suspension rail, as it was not a part of the provided parts I must have missed it where they suggested to use that. I did not see this in the instructions. I think I would be introducing another level of complexity into the project. If you think it could work for you, please let me know how it turns out 😊👍🏾

[@janicedizon1129]

@@TowneBlvdTiy yeah,i think you buy it separately but doesn’t really look stable. Especially when compared to what you did. Thanks again for the video and reply.

[@PhilBuckman]

I bought the suspension bracket. What they don't mention ANYWHERE is that it doesn't work with this particular Besta cabinet. I now have to figure out a hack like this to mount the cabinet since it's made to mount into studs placed 20" apart. Not sure if that's the European spacing, but here in the US, standard spacing is 16". Really lame design, IKEA.

[@OrlandoTSAI]

thanks, finally I understand before I want to buy, I hear tv unit is different to mount on the wall

[@TowneBlvdTiy]

Hi there, Thanks for watching my video and the feedback question. I'm glad if my video was able to help you with your understanding of the challenges of these units. Feedback like yours inspires me to keep making these videos 😄 Thanks again for watching and the subport to help me grow my channel👍🏾

[@larrysd9878]

How well is it holding up a year later?

[@TowneBlvdTiy]

Hi there, Thanks for watching my video and the feedback. After a year it's still as sturdy as the day I corrected the install by using the studs. Hopefully that answers your question Thanks for watching and the subport to help me grow my channel 😄👍🏾

[@saitejagatadi9711]

Hi, Thank you so much for the video... Few doubts: 1. We have concrete wall, which screws(size & brand) I need to use for wall mounting

[@TowneBlvdTiy]

Hi there, Thanks for the feedback. Since you have a brick wall, you most likely will need a power drill with a masionary bit. You would need masionary screws (blue) and a ratchet to help drive in the screws. Normal screw driver won't do it. Drill the holes almost as long as the screw that would be in the wall. Having the brick is easier to find a place to hang the unit but it could be a little more work drilling the holes to attach. Hopefully that helps🙂👍🏾

[@saitejagatadi9711]

@@TowneBlvdTiy thank you so much

[@jolandanoble3470]

Great video, I am about to order the Besta and was wondering if you could use the suspension rail to hang the tv cabinet? Ikea says you cannot but why not?

[@TowneBlvdTiy]

Hi there, Thanks for watching my video and feedback. As for the suspension rail based on what I see there is not enough debth and height with these units to allow you amply screw Into the unit safely. You would probably be screwing into the body of the unit but with the back panel removed. This would be on the upper section of the unit. At any rate you MUST screw the the suspension rail into the wood wall studs. As seen in the video I used the wall wood studs and used a single bracket (s) system to attached the unit from the upper end. If you are convinced that the bracket would work, remember Safety First, before you try it. Hopefully my response was helpful ☺️👍🏾

[@rafabeato1]

Hello there! thanks to your video I'm confident that I can do this in my NYC apt so, cannot thank you enough! but may I ask some clarification about the process? you have answered this already but I just want to make sure. The first two end screws that you drill on the wall to mount the unit on min15:00 , did you use regular screws without anchors? and was that only to set the unit into place so that then you can change the position of the brackets? 2nd: did you only move the middle brackets to where the studs are? or all of them to where the studs are? 3rd: the bracket has 3 holes, when you relocated the brackets to the stud, did you used the IKEA screws for the top part that attaches to the unit with 2 screws? and then a longer screw for the lower single hole? and are the brackets that easy to move? I apologize for all these questions if you have time to answer them it would be os so much help.

[@TowneBlvdTiy]

Hi there, Thanks for watching my video and I'll try and answer your questions the best I can. Q1: That was based on the initial instructions. You will notice that the instructions do not mention plugs nor does it come with any! It the end they will Not hold. I noticed the unit slowly slipping some time after before it fell and secured it with the bench as you see in the video. Q2: I moved All the brackets to where the studs were just to be sure it was safe. You are better off going straight to find the studs and mark the screws there to attach the unit. Q3: For the upper end of the brackets I used the original Ikea bracket and screws But for the Wall studs I used some slightly longer wood self tapping screws that I had left over from another project. Hopefully that answers your questions and helps you with this project. Good Luck and let me know if you have any further questions 👍🏾😄

[@rafabeato1]

@@TowneBlvdTiy oh my god thank you for replying to my questions and so fast! I'm going to get the Besta on Tuesday will definitely let you know!

[@erictappan1110]

Thank you for this! Just ran into this problem, would only hit 1 stud since I'm all at the usual 16"oc. Do you find the brackets are sturdy enough supporting from the top rather the sides?

[@TowneBlvdTiy]

Hi, I used the original brackets and screws for the top. Yes, I found in my situation that they were more than strong enough. I just used longer screws to attach it to the wall studs. Hopefully that helps 👍🏾

[@maamiserwaa1286]

@@TowneBlvdTiy nice job.pls what screws did you use to mount it on the wall?

[@TowneBlvdTiy]

@@maamiserwaa1286 Hi, I used screws that I had in my tool box that were longer and just as strong. The ones that comes with unit may not be long enough to reach the wood studs. Hopefully that helps.

[@ASpec818]

Did you drill the first two screws in drywall to hold it up? Your tip about relocating the ikea brackets to line up with your studs was helpful!

[@TowneBlvdTiy]

Hi there, Thanks for the heart felt feedback It makes me happy that my video was able to help. Yes pre-drilled the holes through the drywall into the studs to make it easier to screw things in place. If you follow the IKEA instructions all the way by attaching the unit to the drywall only (pre-drilling the holes or not), you'll end up in trouble. 😄👍🏾 Thanks again for watching my video and the subport to help me grow my channel.

[@kirakeeks6466]

Any advice on the doors and installation being done just as directed but their still are on uneven !

[@TowneBlvdTiy]

Hi there, Thanks for the feedback. When installing the doors, don't tighten up the doors all the way. Position them where you want them and slowly tighten each side starting at the bottom. Then tighten up the rest. There are also screws on the left and right side of the bracket itself that allows you to adjust the door. The screw on the right will allow you to align the door to be flush with the cabinet Hopefully this will help you with some directions to get the doors more even. 😄👍🏾

[@StandinOnBizNes]

At 25:11 Them things that was on your tv stand that you screw on the bottom, did you use them or no?

[@TowneBlvdTiy]

Hi there, Thanks for watching my video and the kind feedback/question. The caps for the bottom that were sitting on the unit, I did not use since I installed the unit on the wall. They are sitting in the left cabinet for future use. Hopefully that helps. Also a big thank you to helping me grow my channel👍🏾😀

[@S60ULX]

I'm so stuck. I bought two of the wall suspension mounts from IKEA to put the same cabinet up but I have no clue how to get them to hook on to the cabinet. Did you not use the wall mounts?

[@TowneBlvdTiy]

Hi there thanks for watching my video. No I didn't use the suspension mounts. I just found the studs in the wall. It would have been too confusing and too much work. Good luck,👍🏾😀

[@travm3978]

Hey man, what drill bit size do you use to install this unit? I need to buy a drill but don’t want to come home needing to buy extra separate parts , thanks.

[@TowneBlvdTiy]

Hey, it was a medium : bit called a Phillips-head screw, that has a slot in its top that looks like a cross

[@TowneBlvdTiy]

Hey : a bit called a Phillips-head that has a slots in its top that looks like a cross. Sometimes they come in 3 sizes, small, medium, large. I used the medium bit. If you are buying a varity screw driver bit set, the you should be o.k 👍🏾

[@bradduke1676]

Did you use the original bracket screws when you moved the brackets to where studs were?

[@TowneBlvdTiy]

Hi, Yes I was able to use the original screws for the Top of the bracket that screwed into the unit But I used slightly longer screws I found on my own to secure the other of the bracket to the wall studs. You can verify the length by tapping into the wall stud with your drill as a slight pre-drill hole. I did want to take any chances. Hopefully that helps👍🏾

[@lillarry3000]

Hey did they provide a keyhole bracket? Can I just put a big bolt?

[@TowneBlvdTiy]

Yes, provided the keyhole brackets, so yes you can put a reasoable s8zed bolt or screw through it. Hopefully that helps👍🏾😊

[@lillarry3000]

I found my keyhole brackets lol but it's very small to hold that much weight don't you think lol

[@TowneBlvdTiy]

@@lillarry3000 it should be o.k as long as you are attaching it to the studs in the wall. I'm using all 4 brackets that were provided and i stll don't have any issues. I'm Not sure what you are planning on putting inside the unit. If you are doubtful you can always use other support brackets. In the end you have to be confident with the attachment. 😊

[@lillarry3000]

How did you screw in support brackets in the the TV unit? And how big were the screws? I can only get 2 studs and I'm planning on using 2 100 pounds ez anchors

[@TowneBlvdTiy]

@@lillarry3000 Hey for the TV unit, because I used the original bracket, which I moved, I was able to use the original screws to attach the bracket to the back of the TV unit and longer screws to reach the studs.👍🏾

[@ilhamnaufal9248]

is there any hole between the shelf to put the cable going through?

[@TowneBlvdTiy]

Hi there, Thanks for watching my video. No there is no pre-drill holes in the shelves themselves. If needed you can use a drill bit for holes and put them in, But if possible try to come in from the back of the unit (through holes) to where you need to connect to applications. Hopefully that helps.👍🏾

[@phoenix112308]

What color is your floor ?

[@TowneBlvdTiy]

Hi there, Thanks for watching my video and the feedback. The color of the floor is a white oak with warm grey blend. Hopefully that helps. Thanks again for watching my video and the subport to help me grow my channel 👍🏾😊

[@irnnr]

Hey, what did you use as the height/difference between the floor and the bottom of the unit?

[@TowneBlvdTiy]

Hi there, Thanks for watching my video and the kind feedback/question. I used 8" from the floor to the bottom of the unit. So the 15" shown in the video I included this measurement. Hopefully that helped. Thanks for watching and the support to help grow my channel 👍🏾😀

[@irnnr]

@@TowneBlvdTiy thank you, much appreciated!

[@kaninramone6365]

Mine didn't come w instructions so ty! I thought I got the wrong order

[@TowneBlvdTiy]

Hi there, Thanks for the heart felt feedback. Thanks for watching my video and the subport to help me grow my channel 😄👍🏾

[@Xyz-d6j1k]

Just attempted to install the tv unit with rail and figured out it's not designed that way after watching youtube... I didn't want to use legs since thats a lot of legs for 2x2 units. Clever that you just turn the bracket come with the unit the other way to mount on stud. As long as no one sits on it, it would be fine.

[@TowneBlvdTiy]

Hi there, Thanks for watching my video and the ultra-kind feedback. Yes, you cannot mount this unit without the studs and I did not even know about the rail system. I'm glad if my video was able to help you. Thanks again for watching and the subport to help me grow my channel👍🏾

[@shecky1]

Hello thank you for the video! When you screw the brackets into the studs...two questions. One: Do you drill through the corrugated board? Or did you make some cut out? It seems weird to bend the board in like that. Two: To screw the bracket into the top of the unit, did you use the same screws? Mine are blunted at the tip. If you didn't which did you use? If you did how did you do it? Thank you for any insight and for the idea in the first place! All the best!

[@TowneBlvdTiy]

Hi there, Thanks for watching my video and the kind feedback /questions. Question 1. It was a bit of both. In the middle of the unit I did not use the backing, so it was a direct screw into the top of the unit first with the original screws. Then I got longer 3" screws to drive into the wall students. On the outer ends once I found the studs, I screwed the bracket into the top of the unit first then through the backing into the studs. Marking things is always a good idea. I used new 3" screws, the originals are not long enough to read the studs. I would recommend that you pre-drill part way into the stud(s) before attempting screw into the stud using a cordless drill and finish tightening a with manual screw driver. Question 2. For the top I used the original screws, but I predrilledinto the top of the unit to create an opening. I also used the original brackets. Hopefully that helps. Also a big thank you for the to help me grow my channel👍🏾😀

[@shecky1]

@@TowneBlvdTiy thank you for the info! In the end I got it sorted out. Predrilling small screws and pilot holes for the larger screws ended up necessary. Then I added a couple extra brackets underneath as one up top was unable to be placed. All in all, thank you so much! Great video and response. Liked and subbed

[@hereaioan3379]

Nice video but i dont understand where the 2 L and 2R pieces if metal ahould fit? In the bag you had them but you did not use them

[@TowneBlvdTiy]

Hi are you referring to the doors? or can you tell me what time in the video you would expect to use them.? For the door, I did not use one of the Plungers as it was optional for the closing. Please let me know.

[@chelay29]

Hello! Thanks for the video! Very helpful. One question? The middle space is like that? or you just dont install a door?

[@TowneBlvdTiy]

Hi there, Thanks for watching my video. The unit does not come with doors, there are sold separately. I did have 3 but only used 2 in the end. I left it open to get to the HDMI cable box in the middle. It was also good I did that as there was no door in the way when my kids wanted to hook up their video games or computer to the TV. How many doors are used is up to you and the look you want to achieve. Hopefully that helps 😊👍🏾

[@itzjustkay1972]

Good Job! Very Nice.

[@TowneBlvdTiy]

Hi there, Thanks for watching my video and the ultra-kind feedback. When I make a video and put it out there, I never know what the impact will be. I'm glad you enjoyed feedback like yours inspires me to keep making these videos 😄 Thanks again for watching and the subport to help me grow my channel👍🏾

[@vishnuvadla2922]

Thank you , the vid is very helpful !!

[@TowneBlvdTiy]

Hi there, Thanks for watching my video and the ultra-kind feedback. I'm glad you enjoyed the video and if it was able to help you. Feedback like yours inspires me to keep making these videos 😄 Thanks again for watching and the subport to help me grow my channel👍🏾

[@MohamedAhmed-bz6mi]

How long do stud screws need to be then can 3 inch work

[@TowneBlvdTiy]

Hi, I'm not sure of your situation but a 3" screw would be more than fine. You may want to drill into the stud somewhat to help with the screwing efforts. Hopefully that helps.

[@MohamedAhmed-bz6mi]

@@TowneBlvdTiy so a 3” stud screw

[@TowneBlvdTiy]

3 inch self tapping wood screw, yes

[@thefreshwes]

Damn I really needed this video.. thank you!

[@TowneBlvdTiy]

Hi there not problem 😁 Hopefully it was able to help you👍🏾

[@Journeyonplanet]

Awesome 👏🏾

[@TowneBlvdTiy]

Hi there, Thanks for watching my video and the feedback. Responses like yours is encouraging to keep going. Thanks again for watching my video and the subport to help me grow my channel👍🏾

[@ryliephuong8994]

Hey mate just wondering the measurements of the unit. Cheers

[@TowneBlvdTiy]

Hi there thanks for watching my video and thefeedback. Dimensions are approximately L70 7/8" x W 16 1/2" x H 25 1/2". Hopefully that helps. Thanks for watching my video and the support to grow my channel. ✨️

[@scott.h]

For those who want to hang a 3 door IKEA Besta unit on the wall using the suspension rails, you need to buy a 2 door and a 1 door and join them together. The one piece 3 door unit, like in this video, is not designed to be wall hung. Unfortunately there is minimal Information from IKEA about this. I got caught out buying the one piece 3 door unit and will need to do some slight modification to make it accept the rails.

[@TowneBlvdTiy]

Hi there, Thanks for watching my video and the feedback. Yes, this unit will not install on the wall if you follow the IKEA instructions to a tee. There is no mention of a suspension rail in any of the instructions, so using one is a user's choice. Anyway you look at it it's still a modification (and complicated one at that). Mine is still on the wall 2 years later and is still as strong as the day I installed it. Good luck your project and drop me back a message to let me know how it turns out. Thanks again for watching my video and the subport to help me grow my channel 👍🏾😊

[@sharifsalem]

Instructions show both floor free standing and wall mounting options and these supplies L shaped brackets are precisely for wall mounting. It’s just that the locations of the brackets doesn’t conform to most stud locations. You could always brace the wall from inside with a supporting piece of wood behind the drywall and that requires opening a whole large enough to do so.

[@786valerie]

Thank you. I was so confused looking for the holes in the back of the unit to attach the bracket that hooks into the railing.

[@dannytay8496]

Awesome video. The mounting screws for the wall are provided by IKEA too?

[@TowneBlvdTiy]

Hi there, Thanks for the heart kind feedback and the subscription. The ones from IKea I felt were just a little too short so I used a few new ones I had from other products, about 3" Because they are so long you should pre-drill into the wood studs a bit. You can use the same brackets from Ikea though. Hopefully that helps. 😄👍🏾

[@echiu5524]

Well done man 👍🏻👍🏻👍🏻

[@TowneBlvdTiy]

Hi there, Thanks for watching my video and thanks for the heart felt feedback. It makes me happy that you appreciate work. 😄👍🏾

[@joshunited]

Installing it now... as I was reading the "instructions" I thought this can't be held up by only 4 screws, with ikea telling you not to even anchor them... while the 2 door unit has a Suspension Rail, go figure. Then 1 of the 5 comments on ikea saying it fell off their wall with wall anchors. So eff the ikea instructions, find a proper stud. ;)

[@TowneBlvdTiy]

Hi there, thanks for the feed back. Yep, did not trust anything other than the wall stud after I noticed it slipping after the initial install. It's just amusing that IKEA does not give plugs or instructions to anchor this to studs 🤣 Good luck with the install 👍🏾

[@SuperBennyMan92]

This was so helpful!

[@TowneBlvdTiy]

Hi there, sorry for the late reply. thanks for watching my video and the kind feedback. Glad my video was able to help. thanks again for watching and the subport to help grow my channel 😄🙂

[@leadbsc]

Great informative video. Thank you.

[@TowneBlvdTiy]

Hi there, thank you for the kind words, and thanks for watching my video😀👍🏾

[@ingridbryan5908]

👏🏾👏🏾👏🏾

[@robertrausch74]

Hey Guys, does someone knows if i can put on plasterboard wall this besta ?

[@TowneBlvdTiy]

Hi there thanks for watching my video and feedback question. Plasterboard aka drywall by itself to support this heavy kind of wall unit is a no go. You risk the unit falling and hurting you or falling and damaging your floor and the unit itself. You definitely need wall studs to attach the unit to to be the safest bet. Hopefully that answers your question. Thanks for watching my video and the support to grow my channel 👍🏾😀

[@Poontang123]

good work shame you took so much of the back out but each to their own

[@TowneBlvdTiy]

Hi there, Thanks for the feedback. When you do a project if I made an oversight that's good so that others don't have to. Thanks for being so attractive👍🏾 Thanks for again watching my video and the subport to help me grow my channel 😄

[@Poontang123]

@@TowneBlvdTiy Your welcome for the support and if you ever need any advice be sure to hit me up

[@Blueythebudgie]

I do IKEA installs for a living. I won't do these due to this ridiculous bracket system. They are for holding furniture back to a wall only to prevent tipping over, such as is the case in their PAX wardrobes. Utilising them to float a unit on a wall like this is dangerous, even if they are fixed into studs. The 2 small screws into the unit itself through each bracket make it, in my opinion, unsafe. Even at my local IKEA store, these units are only displayed with legs on the floor. Go figure? I'd also be interested to know if your unit is still actually hanging on the wall? Placing the brackets as you did here transfers all the load to the pin and plastic cams under the top panel. I wouldn't recommend this modification to anyone. Their other BESTA cabinets use the suspension rails so why they designed this unit as they have is beyond me.

[@TowneBlvdTiy]

Hi there, thanks for watching my video and the great feedback. To answer your question up front, Yes, the unit is still in place and is as strong as the day I put it in. The unit does come with the instructions on how to attach it to the wall but if you follow them to a tee your unit will come crashing to the floor in minutes later. There is no mention of a bracket system or the studs. I know from the installation of the Tv above the unit (which is still in place, I have a video for that too) that you need Studs to support this kind of weight. The use of the studs is the only way to go in my opinion. I used the same metal brackets that they provided with longer screws to reach the studs, the plastic cappers were not modified. The screws into the top of the unit is not an issue size and strength wise. Since you are close to IKEA you probably can probably communicate to them to clean up the instructions before someone gets hurt. The designers probably needs to install the product and do a QA check afterwards☺️ Hopefully that helps. Thanks again for watching my video and the subport to help me grow my channel 👍🏾😊

[@r.b.m.3211]

Talk, explain what you are doing. The music doesn’t make sense for a video of this type.

[@TowneBlvdTiy]

Hi there Thanks for watching my video and feedback. Sure maybe this video art style is not you and everyone. I get that, I think my voice sounds weird. Is there a particular section that you want me to explain? Music is hard these days. KZbin will put halt strikes against my video with copyright violations if I use popular music. So I'm left to scrange around for music that won't get me banned. Thanks for watching, Cheers 👍🏾

[@kia5774]

Hi, can you tell me what screws you use to elevate the cabinet IKEA did not provide those tools