Impact Driver. How To Use It. How To Disassemble It.

[@joeniemand9047]

Lovely seeing the mechanical version of this. Brilliant! quite a valueable tool to have that seems simple enough to use. thanks for your video. I enjoyed it.

[@CYC123]

Hello Joe. I’m so glad you enjoyed the video. The hand impact driver is a good tool. Thank you for the comment.

[@David_Hogue]

This is the only tool that could remove my aging door hinge screws covered in layers of paint and already partially stripped.

[@CYC123]

Hello David. Thank you for your comment. The hand powered impact driver is a really versatile tool, everyone should have one. Take care Jim

[@steveharvey1398]

Such a helpful video! Thank you so much for your instructions on both on how to use the impact driver and also the principles of how it works. Really liked your friendly approach, and well produced video. I certainly learnt some essential things today!

[@CYC123]

@@steveharvey1398 Hello Steve. Thank you for your kind words. I’m so glad you liked the video. Take Care Jim

[@mtrigby]

Thanks so much for explaining why you have to compress it before striking. Watched other videos and they didn't mention it, just assumed everyone knew. Was just about to send my second one back to Amazon because it didn't turn ! Watched this; two whacks of a hammer and it's loosened. Finally.

[@mtrigby]

Subscribed 👍🏻

[@CYC123]

Hello @mtrigby. Well done researching into the impact driver and getting it sorted. I'm glad you found my video useful. Thank you for your comment and I hope you never find a bolt or a screw you can't now remove. Take Care Jim

[@CYC123]

Thank you for subscribing, have a look at my older videos you may find something that interests you. I think they are all good, but perhaps I'm a little bias! Take Care Jim

[@chongshenchang9367]

Thankyou for this valuable info. I actually have this impact driver with me but don't know exactly how to use it. Now i know..

[@CYC123]

Hello, I am glad you found my video interesting. Thank you for your comment. Take Care Jim

[@white_wolf79]

I had to buy this tool to unscrew my handlebar end screws , but I wasn't sure how this tool actually worked. Thank you sir!

[@CYC123]

Hello White_Wolf79. Thank you for your comment. I'm so glad the video was of use to you. Take Care Jim

[@kvppvk]

Truly excellent. Thank you for your time.

[@CYC123]

Hello Keith. Thank you for the comment and kind words. I'm glad you enjoyed the video. Take Care Jim.

[@mikenco]

I replaced my impact driver yesterday after 30 years. The little cups inside had crumbled. Luck would have it, I found a Sykes Pickavant Impact driver in a garage I was clearing out. Looks like it has never been used! ... Top tip with the grinding paste!

[@CYC123]

Hello again Mike. I find I don't use my impact driver very often, but when I do need it it works so well, and it doesn't need any power. Take Care Jim

[@peem1244]

Hi Jim, hope you're well. Really interesting instructional video all about the humble manual impact driver and its design and function. It's sometimes the simple things that get the job done. How about a video on the Yankee screwdriver? I recently acquired a couple of hex bit adaptors for my two yankees making them a bit more flexible now. Thanks for sharing. Stay safe and keep up the good work.

[@CYC123]

Hello @peem1244. Thank you for your comment. I think your suggestion of Yankee screwdriver is good. I inherited one from my Dad, I’ll have to dig it out, give it a closer look, thanks again. Take care Jim

[@torjiesweeten3482]

what to do when the bit gets stuck in the driver?

[@CYC123]

Hello Torjie. If your bit gets stuck in the end of the driver then do this. Strike the side of the bit with some thing light and hard, a screw driver shaft or a spanner, or a small hammer, work round the out side of the bit. If the bit still wont come out then hold the adaptor of the screwdriver in the vice then repeat what I said above. That should free the most stuck bits. Thank you for your comment. Take Care Jim