Impact Power Block / Plenum Upgrade Installation

[@alfredsturdivnat9267]

Thanks immensely for the tutorial on installation of the power block. It's gratifying to get a tutorial video by someone who actually knows the names of the parts of the rifle.😉

[@utahairgunsworkshop]

We do what we can haha. Glad to see it was beneficial! Thanks for watching

[@eljuan4465]

Thanks for the encouraging and knowledgeable video on the installation of the power block and plenum, you really know what your doing and what each piece is called.

[@realblakrawb]

The only change appears to be in the stainless valve body itself (missing slots and bore change) . If im not mistaken you may be able to retain the serialized block. I didnt guage pin the transfer to check for more subtle changes. Not shooting 40 grain slugs, i wouldnt have bothered with the upgrade in hindsight.

[@matiasfelipelaranavarrete5757]

My FX Impact is set at 130 bar, but after an hour of resting, it goes up to 150 bar. Which O-rings could be failing? Excellent videos!!

[@monkpato]

Great tutorial!

[@utahairgunsworkshop]

Thank you!

[@andrewwyllie1081]

Clear and concise video. What is the make of the gun rest/work stand you are using ?

[@utahairgunsworkshop]

It is a Tipton Ultra Gun vise

[@Hemnmahmmod]

Thanks for the vid, what is the use of the installing power block??

[@earnestrussell4437]

I received 3 NBR 90 o-rings and 1 NBR-70 O-ring along with 3 little black balls is there some place I am missing the NBR-90 Oring during the install and what are the three small black Buckshot looking things?

[@gentzacr]

I just received my kit and found the little black rubber balls. Did you get an answer on where these go?

[@surreallife777]

I’m not sure I understand. I was going to buy FX Impact Mark 3 but it’s really expensive in Canada. I found a really good deal on a Mk2. I’m not clear on a few things. Does the Mk2 come with dual regulators from the factory like the MK3 or do you have to upgrade it? Does the addition of a power plenum 720 cc produce more consistent shots and more shots or does it have to be in conjunction with a dual regulator?

[@robertl3126]

Hello,can you tell me is difference in power plenum size from M3 to M4 in length or diameter as M3 has 720 and M4 750ccm,iHAVE M4 btw,if u know or could could measure length and diameter of plenum in M3,cause i need to upgrade some part of plenum and size is a key,thank you very much.

[@johndanville6643]

I love video like this

[@vincentvalerio915]

So essentially you can covert a mk2 to an m3 with the exception of the duel reg ?

[@nikanim]

Can that Upgrade be used on the first Impact MK1?

[@utahairgunsworkshop]

Yep!

[@douglasguerrero7403]

Hi good video body,but i did like you did but i dont know why now dont have power when i shoot....power block it have 150 y the 1 mitter have 180 but when i shoot it does not power....i dont know what it gronw....could you give any idea? Thank.

[@danielharris3827]

If I get a M3 these items are included? I am close to a purchase!

[@utahairgunsworkshop]

Yes, on the new M3s they do come standard

[@hightidelowtide6380]

@@utahairgunsworkshop not the early M3s

[@islacouledouce]

Hello. My seller says that the FX M3 sold in 2022 are already equipped with the new power unit. How do you know if it's true?

[@utahairgunsworkshop]

Every new M3 would have one. This is for an upgrade from an Impact/Impact x/MKII etc..

[@hurricaneaquatics]

To my knowledge, early 2022 M3s had the Power Plenum 720 cylinder, but do not have the Power Block. That's how mine is and I'm a bit disappointed. Take out your magazine and look at the back of the block. If it has 4 holes, it's the new power block. If it has 6, it's not the power block.

[@islacouledouce]

@@hurricaneaquatics A friend of mine bought the FX M3 with the new PowerBlock. We tested both but didn't notice a big difference. However, the two FX were at the same settings.

[@hurricaneaquatics]

@@islacouledouce Thank you for letting me know!

[@Donny_Juanny]

How bad is it if I get minor tooling marks on the rod that the C1 attaches to? I have some minor tooling marks/scratching from where my pliers attached behind the C1. Do I need to replace this rod?

[@mackellyman5642]

Yes, otherwtse you will be thinking about it during a crucial Match...

[@margaritavalencia1873]

How much do you guys charge for the upgrade?

[@philiprogers4071]

Isn't that valve house the old type?, The new ones come with three large long cut outs..

[@utahairgunsworkshop]

The three large long cut outs are for pre-power block power plenums. Power Block valve houses do not have O-rings on the outside. They are inside the power block/power plenum

[@philiprogers4071]

@@utahairgunsworkshop ah, thank you, that makes perfect sense..

[@MT_SLUG_RD]

No es obligatorio quitar el martillo 😊

[@Hipporider]

Gotta say, the music is annoying and unnecessary