This is good. I've been wanting a feature like this for years.
@padcom3 жыл бұрын
Why?
@flat-earther3 ай бұрын
this is awesome. I got it working with 3pos switch. my VTX supports 4 power levels though so I had to skip one power level. I would have wanted to use all 4 power levels with a pot or 6pos switch, but at 2:55 you only showed how to do it with LOW, MID and HIGH logic conditions which only gives me 3 power levels.
@FPVUniversity3 ай бұрын
You can use GREATER LOWER conditions too. It's just a general frameworks
@padroooo2 жыл бұрын
Thank you my friend, I was able to follow your instructions using INAV 4.0.
@JoeSmith-el9yt2 жыл бұрын
This was extremely helpful, thank you tons from USA!
@Terry_Fritz3 жыл бұрын
This is much simpler than an automatic version somebody posted on KZbin some time back.
@MCsCreations3 жыл бұрын
Awesome tip, Pawel! Thanks a lot! 😊 Stay safe there with your family! 🖖😊
@undeze3 жыл бұрын
Yes, this works for me on iNav 2.5, Thank you
@rizasenna88963 жыл бұрын
Thanks Pawel.. its help me a lot...
@yngndrw.3 жыл бұрын
Really like the programming framework and the example you've given for its usage. The only thing is the flashing status indicator for the Set VTX Power operation, the fact that it only operates on change is a perfectly reasonable internal implementation detail but this should not leak out into the UI. The status indicator should represent the logic status only, which in this case should remain on. As it stands it's confusing at best. Also the options in the operation dropdown should probably be grouped into categories: www.w3schools.com/tags/tag_optgroup.asp
@willowncfom82283 жыл бұрын
This works fantastic for 3 switch position (arm changes to 100mW low switch position, 400mW middle switch position, but high trying to get to 800mW will not budge) but I'm not getting output to 800mW with Succex-Force 25/100/400/800, playing with all values. I think the highest should be 4 but that only chnges it to 400mW.
@divingfalconfpv46023 жыл бұрын
Yea I did this on betaflight.. vtx power but on a dial to be able to switch between 5 power settings.. actually made a how-to video for a couple people.. everyone ask. It comes in handy especially on my LR when I decide to go further
@divingfalconfpv46023 жыл бұрын
@@M-H433 I have never used iNAV i did it with betaflight. Beatflight you enter power range like 900 to 1100, then 1200 to 1400, then 1500 to 1700, then 1800 to 2000.. then on transmitter I select the dial as that aux/channel. kzbin.info/www/bejne/Y2atnIObZ8tod5I in iNAV i believe you will have to use great than and less than and nor. To change as it gets higher. Seems complicated. Maybe Pawel knows a easier way. I also set my transmitter up than its always in 25mw when disarmed no matter where switch is
@divingfalconfpv46023 жыл бұрын
@@M-H433 Oh found this kzbin.info/www/bejne/jJWZdnWoabaMl5o
@antlerhanger2 жыл бұрын
Fantastic information ..Thanks you so much
@goku4453 жыл бұрын
Very nice but does it conflict/override the VTX power configuration if set to always low power until the model is ARMED? And how about the value if the transmitter is powered off or if the FC is powered on before the Transmitter?
@MessingWithCode Жыл бұрын
Thanks so much
@FPVUniversity Жыл бұрын
You're welcome!
@nightrider22593 жыл бұрын
Cool af, thank you Paweł!
@TeamYankee22 жыл бұрын
Just revisiting this after moving to Edge TX... I have the low power to high power toggle on the arming switch 🙂
@FPVUniversity2 жыл бұрын
Yup. Inav can low power when disarmed and high power on armed too
@juliencc35882 жыл бұрын
Thanks a lot for this tips!
@FPVUniversity2 жыл бұрын
Happy to help!
@verytech32123 жыл бұрын
Thanks! Really helpful thing.
@flat-earther3 ай бұрын
I want to use pit mode with my IRC Tramp VTX but the pit mode setting in INAV OSD menu doesn't work, it's not doing anything... I will appreciate if you repair it
@Indonesia01ian5 күн бұрын
How can we select the power in that comment? My VTX has 1600mW. If I want to set the option to be 300,500, 1200,1600
@johndeesfpv92892 жыл бұрын
THANK YOU
@sompongpire30273 жыл бұрын
What if I bind the logic condition to rssi channel instead. Can it be used to change vtx output based on signal strength?
@mauxx913 жыл бұрын
Unfortunately makes no sense, since Rssi is based on your RC control and since the receiver video is in the Google you cannot have that Rssi data easily on the fc to be able to implement that logic
@702Wolfi3 жыл бұрын
Thank you sir!
@sdellava2 жыл бұрын
Nice shirt ! :)
@itsazay Жыл бұрын
Sir i cant changing 800mw on my hglrc vtx on inav pls help me to change it
@romanlyamzin32643 жыл бұрын
Cześć Pawlik, i'm not sure that you answer here, but ask however... I can't reach a success. My setup: cloned Omnibus F4V3 pro with Inav 3.0.0, TBS Nano Rx, VTX5848 lite, Jumper T16 Tx. FC configured by video, "Programming" tab's blue dot behavior is right, but looking in goggles power output still invariable. Co jest nie tak? Dziękuję...
@micrathenefpv3 жыл бұрын
Thank you. Is it possible to set Pit mode with a switch?
@aurelienwittmann41053 жыл бұрын
Yes that can be done on the modes tab
@flat-earther3 ай бұрын
did you figure out how to do that?
@flat-earther3 ай бұрын
@@aurelienwittmann4105 how? I did not see PIT MODE in the modes tab.
@egemenx58132 жыл бұрын
Hey Pawel it s a nice video dude.. you know this work thank you.. I apreciate you... I will ask a question about this.. Can we power off the vtx? For example we test smt, and we dont use camera so vtx is working and it becomes very hot .. if we can power it off, it will not be hot...it will be cold.. what is your theory::) ?
@FPVUniversity2 жыл бұрын
Some FC have PINIO that just cuts off power. No voltage, no heat
@egemenx58132 жыл бұрын
@@FPVUniversity I use hglrc f722 I think this have PINIO
@fpvandrelax62153 жыл бұрын
Good !!! Спасибо!🖐️😃👍
@itajailima2009BR3 жыл бұрын
Hi, Pawet. I'm riding a racer drone with an Inav/Matek f405 se flight controller but, i can't get my radio transmitter(AT9S Radiolink) to "talk" to that controller. The bars on the reciever do not move when i make the settings for Sbus. My reciever is a Radiolink RD9S and the bind with the radio is okay but, on the radio transmitter screen, appears a configuration information that says: "Output: PPM". I wire the fc to the ppm serial port but, in the inav configurator, the channels bars on the reciever are all blank. What's wrong? Did i forget to do any important settings? Can you help me with this, please? A hug, my friend. Itajai Lima.
@ruisimoes36382 жыл бұрын
Hi! Great feature!! I am trying to implement on 2.6. No success. I can change the vtx power with the stick commands (radio), and i can see the in the receiver the ch7 changing values. I can change a global variable value acording to the switch position, but when i try to set the vtx power.. it doesnt work. Is this some 2.6 limitation? (TBS Unify and Matek F411 Wing)
@Chris-vc1dh Жыл бұрын
how inav will know what really power to use on vtx ?
@damianmroz872 жыл бұрын
Can I use It to switch on and off my Caddx Peanut?
@fpvkabo3 жыл бұрын
is there any difference in power levels as in smart audio is 1,2,3,4,5 etc vs tramp which is 25 100 200 etc is tramp still like smart audio 1,2,3,4,5?
@Simpo202 жыл бұрын
I have used this guide for setting up a few wings now and it works great! I just tried to setup HDzero 1W VTX in the same way (as it too uses smart audio) and I was very dissapointed to find out that SA is not supported on HDZero for INAV. Is this something that will be rectified in the future? I know alot of people just say "just switch on the ground".... I like to launch in low power mode and increase/decrease as required.
@FPVUniversity2 жыл бұрын
HDZero does not have smart audio
@Simpo202 жыл бұрын
@@FPVUniversity Tried to post a link in the last reply and think it has disappeared, Page 3 of the HDZero Manual states that RaceV1, RaceV2 & Freestyle VTX all use Smart audio.
@JekleFPV Жыл бұрын
Love this, need this! But is it possible in any way to use more power levels? I have it set up on my remote to incrementally change power levels, including pit mode (no pit mode during flight of course). So I have 5 total.
@FPVUniversity Жыл бұрын
No, at the moment it's not possible. Maybe in the future
@MrVasmikey3 жыл бұрын
I use stick commands currently. Will this setup defeat the stick commands?
@flat-earther3 ай бұрын
I don't think this setup will defeat the stick commands b ecause as Pawel explained at 5:14 the power level override is executed only once when you flick the switch.
@billkendall74643 жыл бұрын
Is it possible to use a toggle switch, like the "Trainer" switch, to cycle through the power levels on the VTX? So, every time you cycle that switch, the VTX power level increases? Obviously it would go from highest to lowest on the last cycle.
@FPVUniversity3 жыл бұрын
yes, you can do it with Programming Framework and Logic Conditions as well
@made-hands77602 жыл бұрын
хорошее видео:)
@DronePlayground3 жыл бұрын
💲👍💲very good video💲😎💲
@martinmacko72973 жыл бұрын
Hi Pawel. Can you please help? INAV2.6 Rush tank ll always stay in pit mode and cannot change power level. Band and channel mode change works but not power. Thx a lot!
@flat-earther3 ай бұрын
did you figure out how to enable/disable VTX pit mode on INAV?
@2000Romu3 жыл бұрын
Hi Pavel. Love your work!!? I have a question. I just wired a flywoo bt nano to my matek f722 running inav. I triple checked my wire ring a'd I'm good.. But when I plug my quad to the computer it goes directly into dfu and won't let me connect normally... Of I remove the bt nano from the board it goes back to normal.. Any ideas..?? Thanks.
@FPVUniversity3 жыл бұрын
Is BT on UART1? If yes, wire it to a different one
@2000Romu3 жыл бұрын
@@FPVUniversity hi, thanks for the answer. No I'm on uart 4..
@robtomben3 жыл бұрын
Pawel, thanks for this info. Question, how can I control my Runcam 2 4k via the remote wire? I've tried many things. I'd like to be able to start/stop recording via switch.
@Terry_Fritz3 жыл бұрын
I have one of these: www.cnfpv.com/portal.php?mod=view&aid=159 for my Hawkeye camera but I haven't wired it in yet as I'm stalled on the build. There are other brands too. Got mine from Banggood.
@robtomben3 жыл бұрын
@@Terry_Fritz The Runcam 2 4k comes with a "remote wire" which they show in the manual being set up and controlled in Betaflight. It's shown being controlled on a servo output. The issue is that I believe the commands entered in the Betaflight CLI interface are specific to Betaflight. I haven't found or figured out how to do these in INAV.
@vitalliart9273 жыл бұрын
@@robtomben in inav it is easy . Read instruction! Two wire rx run cam to tx of flight controler and tx of run cam to rx controler . In i nav open port to run cam video devices. Then in i nav. Go to switches and tune your remote in camera control. Boom 💥 done working good . Put switch in mid position then u can use same switch for changing qr mode and record mode
@dwexoticmaple3 жыл бұрын
why do you need to change the power level is that so you don't need to solder board?
@dwexoticmaple3 жыл бұрын
oh output power ie 25mw 50 mw 100mw for eg
@olivierf.49313 жыл бұрын
Hi Pawel ! do you know how to crank up the vtx when the option is inaccessible in Betaflight? I am stuck with 25mw on my cinefun and it can go up to 200 :-(
@FPVUniversity3 жыл бұрын
How about setting the power with a onboard button?
@olivierf.49313 жыл бұрын
@@FPVUniversity you mean pushing a button on the vtx board?
@padcom3 жыл бұрын
Now that I think about it... if it'd enable setting the VTX forcibly into pit mode when disarmed it might (I repeat: might) come in handy :D But then isn't there already a setting that turns on pit mode in disarmed state?
@flat-earther3 ай бұрын
did you find out how to use pit mode in INAV?
@padcom3 ай бұрын
@@flat-earther Yes and no. I've defined an adjustment that chances the VTX power output. I use it when flying long range in 3D cruise where I have a moment do other stuff than keeping the plane in the air, because it flies by itself. But pit mode when disarmed - not really, no.
@danieledm01013 жыл бұрын
Is this can be used to turn of the vtx too?
@emanuelstassar3 жыл бұрын
Hi Pawel, thanks for explaining this so clearly. It works for my setup, but with a strange glitch. Power level 1 is 25mW, when I switch to lever 2, nothing happens and when I switch to 3 I get 600mW. If I then switch back to level 2 I get 200mW. What could be the cause of this? I am using a DarwinFPV TX805 with 25, 200,600 and 800mW connected to a Matek F411-Wing FC.
@Pilot-et7dh7 ай бұрын
I have tre same issue
@droneoleng3 ай бұрын
Saya menggunakan inav7, vtx happymodel ovx 306, open vtx. Saya mempunyai permasalah vtx power level tidak bekerja, apakah ada solusi untuk permasalahan ini. Terimakasih.
@FPVUniversity3 ай бұрын
wybacz, ale nie mam pojęcie o czym do mnie piszesz
@droneoleng3 ай бұрын
I am using inav7, vtx happymodel ovx 306, open vtx. I have a problem with the vtx power level not working, is there a solution to this problem? Thank You.
@andrewjamez3 жыл бұрын
do you need to have a lua script loaded into radio?
@FPVUniversity3 жыл бұрын
No, absolutely no. It works with any radio and any radio protocol. No need to have any Lua or telemtry as well
@andrewjamez3 жыл бұрын
Awesome thanks
@andrewjamez3 жыл бұрын
@@FPVUniversity I see in v2.6 the baud rate selection doesnt include default or auto. Do you know what the correct baud rate is for smart audio? Thanks
@padcom3 жыл бұрын
Paweł, I frankly don't see value in switching power levels on the VTX. If you consider 100mW vs 800mW it is not that big of a difference for long range and the mental overhead of switching VTX power mid-flight is high enough to keep you away from actually controlling the aircraft which in my opinion makes this feature not worth while. Even in racing you'd want to stick to one power level to focus on controlling the drone. So a no-no for me (although it is cool to see inav being able to do that :D)
@goku4453 жыл бұрын
You've got a point. Anything can distract you from actually flying your plane but it can be really useful if you want to test which powerlevel is actually adequate for your flight distance. Once it's done you can always use the channel for something else. I think it's a great feature.
@gajufpv90323 жыл бұрын
If you are flying a stable airplane it is not so difficult. And if you don't want to do it with a switch, you can change the vtx power according to the home distance if you have a GPS or rssi value
@360_tours2 жыл бұрын
Does inav use VTX tables? My vtx keeps crashing
@FPVUniversity2 жыл бұрын
No, no VTX tables, because it's a useless function. Still, INAV supports SA and Tramp protocol to change power and channel
@Pilot-et7dh7 ай бұрын
@@FPVUniversity hi Pawel. My VTX on tramp wont change power to 2500/ it sets only 600mW. Could you advise on this? thank you in advance.
@BountyFPV3 жыл бұрын
IT DO NOT WORK ON TYRO 129 AT ALL..... :(
@alexglikman86293 жыл бұрын
Open tx logic inside inav.....
@chiprobertson30944 ай бұрын
It would be better if it was like betaflight 😢
@SId0rich3 жыл бұрын
WTF is going on? Why only on your videos sound constantly desinchronize with picture on 1.5-2x speed?
@icanfly54303 жыл бұрын
Нихера, всё ок и на 1.5 и на 2.0.
@SId0rich3 жыл бұрын
@@icanfly5430 мои поздравления! А у меня звук постепенно уходит вперёд, потом видео подвисает, синхронизируется и цикл повторяется.
@icanfly54303 жыл бұрын
@@SId0rich На чём смотришь? Какой девайс, какой браузер?
@SId0rich3 жыл бұрын
@@icanfly5430 всегда хром, остальное меняется от случая к случаю. Но проблема бывает как на 8-ленем ноуте с i7 и убунтой так и десктопе с зеоном и gtx1660s с вин10, ктороый в соседней вкладке с ютуба 4к 60фпс на х2 скорости будет плавно воспроизводить.
@BBFPV3 жыл бұрын
Does this work with TBS Pro32HV?
@tractionman91203 жыл бұрын
It should, as long as it is set up for Smart Audio. Unfortunately iNav does not yet seem to support CRSF as communication protocol between the Flight Controller and VTx.
@coulsonrobert3 жыл бұрын
Hey Pawel. Great video and channel, many thanks. Quick question, is it possible to do a 5 stage vtx power setup using channel values (eg on the 6 pos switch on the TX16S). My VTX has 10/25/200/500/800mW. Your logical conditions just showed 3 stages of low/med/high.
@FPVUniversity3 жыл бұрын
yes it's possible. Take a look here for example: github.com/iNavFlight/inav/blob/master/docs/Programming%20Framework.md#set-vtx-power-with-a-pot
@coulsonrobert3 жыл бұрын
@@FPVUniversity thanks you’re a gentleman. I’ve managed to do it by using a logical condition RC channel 7 = 988us etc, one per stage of the 6-Pos switch. It works but my concern is if the channel drifts a few microseconds then I guess it won’t trigger?
@supernova1969a2 жыл бұрын
@@FPVUniversity how would I go about using the 6 push switch's on the top of TX16S? Thank you for your hard work! I truly appreciate all that you do
@Chris-vc1dh Жыл бұрын
how do you put in inav vtx table?
@FPVUniversity Жыл бұрын
INAV does not need vtx table. Everything works just fine without it
@Chris-vc1dh Жыл бұрын
@@FPVUniversity so it will never know power as every vtx is different
@FPVUniversity Жыл бұрын
@@Chris-vc1dh but why INAV should be aware of the output power?
@Chris-vc1dh Жыл бұрын
@@FPVUniversity to display it on osd for example
@FPVUniversity Жыл бұрын
@@Chris-vc1dh but it's for your knowledge, not for INAV to know
@harrytmurphy84383 жыл бұрын
Can you do this in Betaflight as well?
@FPVUniversity3 жыл бұрын
From what I know, not
@flat-earther3 ай бұрын
yes you can through CLI I have done it
@federicosagun46153 жыл бұрын
Hi Pawel what is the use or benefit of this switches??