Infiniti I30 Replacement Remote Programming 1996 2000

Visit us at www.carandtruck...
Please read carefully before trying! If at any time you make a mistake, start and stop your car, exit the vehicle and start over. The remote can be only programmed with a master key
1. Sit in Infiniti I30 car with doors and windows closed.
2. Lock Infiniti I30 doors with power door lock switch on driver's door.
3. Put in and pull out key from Infiniti I30 ignition approx. 8 times or until you see the hazard/turn signal lights flash.(older models lights may flash after 4 or 5 times) you need to do that in less then 10 sec
4. When hazard lights flash (on 2005 and newer models the gauge needles may jump a little instead) , put key in ignition and turn to the acc position.(when your hazard lights flash your car is sending a signal to be received by the remote)
5. Press lock button on the new Infiniti I30 remote, lights should flash again.
If you have 2 remotes, 1 new and 1 old or 2 new ones, please continue with steps 6 and 7. If not, skip to end.
6. Press unlock button on Infiniti I30 driver's door, then lock button on drivers door, lights will again flash
7. Press lock button on 2nd new or old Infiniti remote transmitter. Lights again will flash.
You are done. Exit Infiniti I30 vehicle and try your remote. It will not work from inside car or with key in ignition.
Note: if your hazard lights flash after inserting your key in and out, but you can't get the remote to program, you may have a dead battery or the wrong remote. If instructions do not work, do it again but when you get in - shut the door, buckle seat belt and lock doors, then proceed to putting key in ignition

[@jenningswest79]

Is there anybody I can tell me why when I go to reprogram another one that an accessories the parking hazard doesn't flash the first part works in the parking light flashes but when I turn the ignition to accessories it doesn't do it

[@JCalibre]

if I buy the ignition key, can I program that myself?? If so, can you post a video of it? ...This one was most helpful! Simple and to the point.

[@carandtruckremotes]

Ignition keys for the Infiniti I30 must be cut and programmed by dealer or locksmith. There are no do it yourself instructions for the key chip.

[@JCalibre]

Thanks. Very helpful.

[@snowfall1771]

Will not work for my 2001 infiniti i30t please help

[@metro33777]

Like your video but I went to your remote site but no 1998 Infiniti can be found.

[@sam-ys6cf]

I bought key less remote for infiniti i30 (KBRASTU15), when i do the process hazard lights blink on car but pressing Lock button on remote does not work, i mean remote is not programming. Can you help me out.

[@carandtruckremotes]

Try rebooting the keyless system by doing an electrical reset on the vehicle.To do this you would simply disconnect one of the car's battery cables for about 15-20 minutes, reconnect and then try the programming again.Sometimes this will solve any 'bugs' that may be keeping the remote from programming.

[@sam-ys6cf]

Tried rebootingand also disconnected the cable for 20 minutes, still doesn't show up :(

[@carandtruckremotes]

Unfortunately you would have to take it to a dealer or locksmith for programming if you cannot get the car to respond to the 'programming mode'. Are you certain the car is factory equipped with the remote system?

[@13browneyez32]

Thank you it worked!!

[@joshuacampodonico6554]

Didn’t work

[@Mimi122396]

I have a 2000 infinity I30 will a i35 remote from your website work for my car?

[@93baby]

Did you ever find out??

[@USCtrojans26]

will an i35 remote, that's available on your website, work for my i30?

[@carandtruckremotes]

No, I'm sorry, but those remotes are not interchangeable.

[@lendaryreviews]

Wait. I can do this to my old car infinity i30 ^_^ heck yea