Learn how to crimp a BNC connector onto an RG59 coax cable with InfoComm University instructor Bill Thomas, CTS-I.
Пікірлер: 41
@codycstone3 жыл бұрын
I have watched a lot of videos on this subject lately... ivmust congratulate you on doing such. Clean job!so many videos of folks just wrecking that braided cable and having all these strands poking out of the crimp piece.. whether it makes a difference or it does not, pride in your work goes a lot further than just looking good. Builds integrity! Nice work again. Thanks for the video!
@AVIXATV2 жыл бұрын
Thank you, Cody! Those stray strands may seem inconsequential, but they can cause some serious problems if they aren't caught. Glad the video helped!
@densilhartney94918 ай бұрын
Pl
@percysayastorre64094 жыл бұрын
Excellent video sir, my respects, I saw tapes videos to strike out a rj11 and rj59 cable, but none like you, I send you my admiration for exposing your knowledge, a hug from Peru
@AVIXATV3 жыл бұрын
Thank you! Glad we could help!
@kunstraser2 жыл бұрын
It's all about the using of proper tool(s). Without it, something will always go wrong.
@leandrofigueredo7151 Жыл бұрын
Cordial greetings from Cuba bring your offers here thanks 👍🇨🇺🇺🇸
@AnilKumar-zo2eu2 жыл бұрын
Thank you sir for your packaged information
@asiavisual5 ай бұрын
nice and clean
@jluke686111 ай бұрын
thank you for the great video
@ILTOURS5 жыл бұрын
THANK YOU FOR THIS FILM
@ravichandransrinivasan54532 жыл бұрын
Hi Bill, Video is good, can you add a view of the crimping tool from the side please.I am particular to see the crimping of centre pin.Some coax have the core wire as multistrand.Can cenre pin crimp well there or do we need to solder with fine tip iron?
@ALLDISHVIDEOALLDISHVIDEO4 жыл бұрын
GOOD VIDEO👍
@tanci68654 жыл бұрын
Super videjko stando pokračuj
@kajmi634211 ай бұрын
Very good you explain well thank you
@hussainalikahlini68032 жыл бұрын
You Alive Now Thomas ❤❤
@AVIXATV2 жыл бұрын
Bill is still kicking it and enjoying his retirement out in Colorado. ;)
@user-vp7zg8ht5v5 жыл бұрын
🙏
@bryanpray22226 жыл бұрын
Need tool part #s please. Thx
@Masterpj555 Жыл бұрын
perfect video.. however elaborating what crimp was being used may have been helpfull..
@alifadhil53772 ай бұрын
I am looking for this exact tool to make the three cut in one time but i can not find it anywhere online , can anyone guid me plz?
@AdeMunaa3 жыл бұрын
selamat datang di welcome ya kak
@anthonyquinn72467 жыл бұрын
I need to buy that strip tool, what is the name of that?
@SpartanMFP2 жыл бұрын
Tequila
@burtonkidd5 жыл бұрын
Informative video, I just received my RG59 siamese and some crimp connectors. I crimped the connector like you did and soldered on my power leads. (- to - + to +) and when i connect the camera and cable to the DVR the inferred clicks on the screen stays black and then in the lower corner i have a capital P with a red x and no picture.
@ximocandelabelso58725 жыл бұрын
Thank you very much, from Spain!! Your're the fucking master
@afsalmuhammed13435 жыл бұрын
Sir the stipper name model number
@oceancollins3 жыл бұрын
Please can you detail the coax stripper used here as had no joy finding one which correctly strips outer sheath and cuts dielectric properly. Looking forward to your reply and many thanks
@AVIXATV3 жыл бұрын
Sadly, we can't do that. We're an association for the commercial AV industry, and we maintain brand agnosticism and will not endorse a product. What I can and will say is that when Googling a rotary coax stripper (especially if you are using it a lot) is that with any tool, don't go super cheap. You don't necessarily have to go super expensive either. Sorry that that is vague, but we must retain our independence. Any tools used in the videos themselves are strictly for illustrative purposes rather than an endorsement. Hope you find on that works for you!
@oceancollins3 жыл бұрын
@@AVIXATV thanks for you prompt reply and advice. I am about up to 1000+ coax/shotgun/power cable run installs and have tried about 8 different coax strippers ranging from £4 UK to about £30 UK. None of which give an adequate braided dielectric section for decent crimping. Most offer 5-8mm braided dielectric section which in my opinion is not good enough for crimping BNC connectors with my CK crimp tool. I shall have stick to my tried and tested method of using a dolphin utility knife of cutting cable sheath and stripping the right amount of dielectric back for centre core pin connection crimp. Once again, thanks for the quick reply
@ryansanderson70237 ай бұрын
My g**d**n stripper keeps cutting too deep at the first blade. It taks off the outter jacker and most of the braided shield. I even have the blade set to shallowest cut. I am using a Paladin LC CST PA1255 on belden 1506 cable.
@afsalmuhammed13435 жыл бұрын
All tools model number pls
@alexisarredondo79048 ай бұрын
Anybody know what crimper he used?
@kylej22245 жыл бұрын
What about compression connectors without removable center conductors?
@andriysvlogs93193 жыл бұрын
Hi, l have the same question? :) However, it should be even easier, just skip one step
@electricalron5 жыл бұрын
BABABOOEY!!!!!1
@romanpopov-Jin3 жыл бұрын
Очень наглядно и понятно , перевод не нужен
@jeff-73 Жыл бұрын
You don't say how to configure the stripper. anyone can just put the cable in the tool and twist. it's like it just magically works out of the box. It doesn't.
@franciscoescuderobustamant77138 ай бұрын
hola buenas, quería adjuntar que este vídeo me parce terrible, voy a acabar con mi vida después de ver este vídeo, ojala el creador de este vídeo al enterarse de la noticia caiga en una terrible depresión que acabe con la muerte, la persona que aparece en el video es la persona mas horrible y tenebrosa que han podido ver mis ojos, saludos desde Guatemala
@raul.stoica_8 ай бұрын
saludos desde mi Perú!
@deniscondrache54048 ай бұрын
Hoy me siento muy bien porque he conseguido un pokemon nuevo. Ha sido un krookodile shiny en la plaza mayor.