Have the same kegerator and had a terrible time with foam. Went through a full 1/6 without being able to get the head dialed in. Tried everything from 5-13 psi and nothing worked. I ended up replacing the tower with a kegco one that screws into the top and now have the absolute best pours at 10psi.
@keffjyles84709 ай бұрын
To get less head put the glass against the spout at a 60 degree angle and slowly tilt it down until your at a 20 degree angle, always make contact with the spout to make a cleaner poor. At that point it should be full with minimal amount of foam. The other settings that help with foam, I dont know about.
@brobet Жыл бұрын
I was looking at getting one of these, thanks for the video!
@patmcclary9380Ай бұрын
Do a 50/50 mix of Nitro and C02
@markleoni60929 ай бұрын
Seems like you are over charging the keg. All micro brews will have enough naturally occurring co2 from brewing. Shut off co2 until you get a good pour. Then start adding co2, to hold pressure. Around 5 lbs on the regulator ,if you co2 is cold Hope this helps.
@QueenCityBeerTube9 ай бұрын
Oh yeah, it's been a year now, we got this down to a science by now
@kendalcosgrove3165 Жыл бұрын
I can’t get the god damn wing nut on top to stop leaking. It just won’t get tight enough. It’s metal on metal and like something is missing in between to keep it flush/tighter. I don’t see any comments with that problem so makes me wonder why mine won’t stop leaking out the top.
@QueenCityBeerTube Жыл бұрын
Our first keg leaked, I used one of the rubber washers that came with the unit, solved that issue.
@keeganwilson7616 Жыл бұрын
I just got one of these. Had a bunch of problems with the foamy beer too. Any advice ? Or have you fixed yours?
@QueenCityBeerTube Жыл бұрын
I uped the Co2 and turned the fridge temp down, that seemed to do the trick. Another viewer suggested a tower cooling fan.
@petergibson7358 Жыл бұрын
What did you up the CO2 to?
@QueenCityBeerTube Жыл бұрын
@@petergibson7358 I have it at 10psi now. We're on our 3rd keg and have had no issues since.
@chriswilson99963 ай бұрын
I just bought this kegerator and I’ve had nothing but problems with foam what do you have the temp set at
@cooldudes4532 Жыл бұрын
Longer beer lines with a small inner diameter
@QueenCityBeerTube Жыл бұрын
I uped the Co2 and turned the fridge temp down, that seemed to do the trick.
@amd6239 Жыл бұрын
You need a tower cooler fan. Sold on amazon.
@TheEvanAlvarez Жыл бұрын
Kind of dumb question but how do you get the wing nut attachment back on to a new line?
@wallacefrey6247 Жыл бұрын
LOL... I have never heard of a guy say "I just want less head", until now.
@QueenCityBeerTube Жыл бұрын
That statement only applies to beer head. 🤣
@AdamRivest Жыл бұрын
You need a longer beer line. 10 feet.
@QueenCityBeerTube Жыл бұрын
It was the keg
@chriswilson99963 ай бұрын
If anybody could help me I’d appreciate it I just got mine up and running Saturday and I’ve had nothing but foam I just feel like I’m wasting my keg at this point I have my drive set at 5 and my psi at 10 and it’s nothing but foam and a little bit of beer at the bottom
@QueenCityBeerTube3 ай бұрын
Whats the temp set at?
@chriswilson99963 ай бұрын
@@QueenCityBeerTube I have it set at 5 right now
@QueenCityBeerTube3 ай бұрын
@@chriswilson9996 our 1st keg gave us a lot of issues like this too. We eventually got a small digital thermometer, got the temp @34 and that seemed to do the trick. Also try upping the co2 to 12-15
@chriswilson99963 ай бұрын
@@QueenCityBeerTube should I turn the temp down on the circle dial to like 2-3 them up psi
@QueenCityBeerTube3 ай бұрын
@@chriswilson9996 On our unit "6" is the coldest setting. I have ours set between 4-5, I didn't want ice build up inside.