⚡Install Amp Speakers Stock Harley Touring Radio⚡

[@Chevy243]

Question thought u shouldn’t run ground wire from amp to the battery directly??? I have a popping noise from my speakers when I hit my air ride switch is this bad ground??

[@sikbaggers]

Coils (fill, dump vavles and compressor relays magnatize and cause a voltage feedback every time they are turned off or on. That is known, What isnt so known is why some audio sytems pick up that noise so much better than others. Typically it is ground issue but not always. Its more common on systems that use RCA cables. that are ran from the head unit to the amps. But again, thats not always the case. First thing I do is eliminate all body grounds/frame grounds. Then I put a diode acorss the positive and negative wires feeding the coils. The diode I use is the 1N4005. The diode has a stripe on one side that must go to the positive wire. The closer they are to the vavle the better they will work. This si the diodes amzn.to/4a4mtEa ...this is apretty common issue on harleys after installing air ride. And this is the fix everyone uses.

[@DoRC]

Looks good. One thing you always want to disconnect ground first and reconnect it last on a battery. that way if you are connecting the positive connection and your tool or something happens to touch the frame or something that is grounded it won't short out.

[@TheXlbuilder]

Great video. I never think that 20 minutes is too long when it is good content. There was a lot of info in the video that we appreciate. Thanks for putting the channel up.

[@z3roxc00l9]

Just purchased a 21' SGS, my first harley. So naturally, wanting to start the upgrade process on the bike. I search up speaker install on YT and I'm brought to this channel. Towards the end I just realized your out of Marion, Illinois. I lived and graduated from Carterville. I live in clarksville, TN now. I'll be certainly reaching out to you guys for an install. Awesome video as well. Was very straight forward.

[@TroyBowles]

thnk you for this video , did answer some questions i had like where you did with the remote wire but also im doing this to a 2020 Road Glide adding 4 6.5 maring Skar Audio and a 400w amp micro

[@sikbaggers]

Glad they video helped troy!

[@ColeSS12]

Could i get a link to the speakers and amp by chance Troy?

[@seanwenchell1034]

As always, another great video Steve. So very much appreciated. Just for the record this video wasn't long at all. Keep up the great work buddy!!!

[@andrewlufi7659]

I really like your videos. The only issue I have is that I feel left out with my older twin cam bagger when you talk about dismantling tanks and wiring.

[@sikbaggers]

Yeah sorry man we dont get that many older models in here anymore to do work on...I try to do videos on them when we do though...just few and far between! thanks for hanging in there with us though...we appreciate that. If you ever have any questions just let me know. Take care, ride safe and have a merry christmas!

[@andrewlufi7659]

@@sikbaggers that is what kind of figured. Is there any real difference in hooking up Ciro lights on a V-twin bagger than an M8? What about a radio?

[@Sicc1978]

Hog tunes sucks for the money, I’m a Rockford fosgate fan, they have plug and play and everything is so easy to install, kills me to hear guys pay for Harley install when they could have used the money for better equipment. Great video and advanblack has some great stuff for half the price! Keep up the good work.

[@motorcyclessoundsystems-mi2785]

You can still do far, but far better, than RF for the price you paid for it. RF IS a great product, but no different from Hogtunes when it comes to Pricing. Too much money for what it does. www.motorcyclessoundsystems.com/ facebook.com/MotorcyclesSoundSystems/ instagram.com/motorcyclessoundsystems/

[@jamesdunn1426]

@@motorcyclessoundsystems-mi2785 no lie i paid 1329 for an RF amp and 4 speakers but man its loud lol im on the fence about flashing radio any ideas of a better way

[@motorcyclessoundsystems-mi2785]

James dunn If you installed a RFG systems and done by a dealer, they should had flashed the radio during installation. If not, consider doing so.

[@jamesdunn1426]

@@motorcyclessoundsystems-mi2785 it wasnt done at install ill have to look into getting it done thanks brother

[@tintshopnc5552]

good to see , maybe some people aren't comfortable doing this job and can see what's in store for them. then make a decision to either get a pro or go it on their own. awesome

[@sikbaggers]

Agreed! I see a lot of jobs come in here that should have went to a shop but hell I give them credit for trying. Just takes a little longer to sort out

[@Gaming_Biker]

Best install vid I've seen. Thank you for all the content. Super helpful!

[@sikbaggers]

Thank you Jerad!

[@eliharper77]

Awesome video brother now I think I’m ready to watch again then tackle this project

[@sikbaggers]

Thank you! Its not too bad once you get in there...dont be afraid to move the oem wires around, cram and position where they will go, just watch pinch points when turning the handlebars and youll be fine.

[@eliharper77]

@@sikbaggers I got it man thanks for the great video again 👌🏻😎

[@carlosirizarry4005]

you are a bad man thanks for keeping it simple clean and professional!!!

[@sikbaggers]

Thank you Carlos!

[@garybutterfras1824]

Great video. I have been looking at videos for the installation like this on my FLHX Harley. I stopped the video several times to make notes so I can order the parts. Never heard of those Ferrell crimps. Solved that wire problem. Fantastic job. I subscribed so I could comment. Thanks

[@sikbaggers]

Thank you gary...those things and the solder heat shrinks will cut your install time way down. Any questions on anything just let me know. Thanks for the sub and checking it out!

[@adkinsrob7269]

the internal pod bracing is there to provide rigidity to the plastic to keep it from resonating at certain frequencies. if you cut a hole in the pod to make more room you prevent resonance, and vibration, but you also prevent sound pressure behind the driver which causes bass loss. the best solution would be to make the pods out of a dead material, reinforce the plastic pods, or pack them with batting material to absorb resonant freqs.

[@sikbaggers]

yes...to make cheap harley and rockford fosgate 55 watt plug and play speakers sound better.

[@landingolflandingolf5907]

I was waiting to hear how it came out!!

[@kevinthompson3776]

Another great video with a ton of helpful info! Keep ‘em rollin! Thanks for all your time and effort and if it hasn’t been said before, I appreciate the fact that you do it all for free!

[@babyhuey79999]

Thank you for you continued support videos, without people like yourself a lot of harley owners would be spending their money on crap OEM upgrads. I do have a question, I have a 2016 road glide, will this amp you have listed fit into a road glide fairing or do I need to find a smaller amp? Thank you

[@austinparish157]

Awesome video. Lots of great Info Same set up for 4 speakers ? Thanks in advance ,Love this channel

[@sikbaggers]

Sorry for the late reply, just got back from Sturgis, but yes its all the same for 2 or 4 channels

[@austinparish157]

@@sikbaggers thank you.

[@lancecarter5424]

Great information. Have you done a video on a full sound system adding speakers in the saddlebags in an Ultra Classic?

[@m.b4524]

Thanks for your time with the videos bud so helpful down here in south Louisiana 10 minutes from the Gulf of Mexico

[@sikbaggers]

Thank you for checking it out man..much appreciated. hows the weather down there for riding right now? Were all rained and frozen out already lol

[@m.b4524]

@@sikbaggers it's been awesome I've been putting few miles on. thanks for time.

[@felixmasis3658]

Great video thanks, very helpful, but the speakers has no tweeters, will still sound good?

[@sikbaggers]

a good mid range will sound great in the front without tweeters...you can always bump it up to something is more full range or add tweeters to mirror holes and move your mirrors to the handlebars..if your bike is a RG then you can buy new grills with tweeters in them.

[@michaelterry885]

Awesome video as always always appreciate the time you take out of your busy day for us can’t thank you enough wish you were in Texas god bless brother

[@crazydman17]

Very informative my man appreciate it glad I watched this before I just jumped in and attempted this lot of moving parts to do but nice job

[@timkelly6272]

Thanks, that's a great video. It's very detailed and informative. How would I go about wiring in a pair of speakers into my saddlebags on my 2017 Street Glide Special with that same set up?

[@toddduffell5211]

Would you reccomend a flash to stock radio for this setup

[@moldmaker1]

Thanks Steven, another great video. If I just wanted to change my speakers on a 2014 ultra limited, (stock system) is there anything special that would need to be done?

[@sikbaggers]

Hey Tim...sorry I missed this comment man...But no its all the same inside there. Biggest pain is to get those pods out to change the speakers. other than that swap them out and use the eq on the head unit to make them sound as good as you can with no distortion at high volumes. Distortion causes heat and heat destroys speakers.

[@ronaldroedell3343]

I love this channel ❤ first timed watched and I'm already hooked. Great stuff.very educational. I dig this.

[@sikbaggers]

Thank you ronald! Much appreciated sir...if you ever have any questions just shoot..I try to check this everyday and get back to everyone.

[@davidcastillo4494]

Thank you for your video but can you tell me what system amp speakers and line output converter you used I think I want to go with this same system

[@sikbaggers]

yes...this video is quite old and there is better out there and this is what I use now for this set up.. Renewed Sound Digital 800.4 EVO-X amp amzn.to/4dGfHFj or new amzn.to/4e15y6B PRV Midrange Speakers - amzn.to/4gWpp9s Line Output Converter - amzn.to/4exZnb3 Youll need amp install gear...power wire, ground wire, connectors, inline fuse, remote wire and 2 rca cables. Here are the links for the ones I use. 8 gauge wire +/- amzn.to/3NpP8cO 8 GA 1/4 inch rings - amzn.to/3YnliMC RCA Cables - amzn.to/3YpA5VV Inline Fuse - amzn.to/487fKZV Blue Remote Wire 18 GA - amzn.to/487LGgp

[@davidholbrook1118]

Thank you sir for the, I appreciate everything y'all do

[@sikbaggers]

Thank you sir! Much appreciated !

[@paulhewson4600]

Good video,,,,I would have liked to have seen Before and After,,,

[@AustinBehringer]

Okay so I'm running the lp7-4 to the sound stream that you have here. Can you explain tying in the remote? Do I take the power outlet remote into the LOC or to my amp? TIA

[@wilkinson949]

Thank you for the video. I see some amps that say you need to 'Flash' the stock unit, and other amps that say no flash needed. Can you comment on the difference, what flashing is, and what you recommend.

[@macdaddyb3054]

Great video can you send me a complete parts list I’d like to do this to my 16 Ultra

[@CamdogSD]

Yeah, I wasn’t aware I needed a line output converter. Amp - $500, Install Kit $200, Speakers x 4 $$$, Hope the LOC doesn’t break the bank. I’m halfway through the install with no instructions or pre-req list. I’m gonna die when I find out it needs to be flashed. Well, thank you for all your help. I would be down a bad rabbit hole right now without this video!!

[@gary_somebody7660]

Is there a link for those plugs with the special tool on amazon ?

[@sikbaggers]

yes sir...right here smile.amazon.com/gp/product/B077VGG18B/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 you can also purchase the ferrels and pliers separately

[@Murph_is_what_they_call_me]

What is the size and brand of the windscreen. I like the low profile look

[@jasonbrodsky2593]

I use the exact setup with the soundstream nano amp. How do you keep the RCA cable from vibrating off of the amp?

[@sikbaggers]

I use tesa tape around the plugs and try to grab part of the port so it holds it all together...and tesa tape wont come apart over time like electric tape. I use this amzn.to/4ab1W16

[@B.wood24]

I’d like to see you do a road king step by step with lowers and saddle bags can’t find one on KZbin

[@sikbaggers]

Hey B! Thanks for checking it out man...and when I get another one in here I will do that...ive done several and never really had a chance to do a video on it as they are kind of time consuming to do.

[@blueeyes242128]

i'm pretty confused on a 4 channel with high level input conversion built in and still used a line level converter - if the head unit and/or speaker wires are that noisy i think id just switch head units - props for speaking up about amp gain - i still check with a cheap scope - even some of the cheap graphing multi-meters are handy for level setting and to make sure you're not clipping

[@sikbaggers]

You can use the HL input over the LOC...I just installed it this way for example because thats what was in the shop that day...If your doing this to other bikes make sure to mark the gains..lesson learned the hard way after a buddy cranked his gains after he left and smoked his amp..im to the point now I even take a picture and store it on my pc and mark whos bike it was. If they bring it back and the gain has been moved...tell them to kick bricks!

[@blueeyes242128]

@@sikbaggers Helping a buddy out with his 2013 street glide but i don't do bikes - how much power do i have to play with on these bikes - i know the stator is 30A at 1000rpm and 54A max but how much does the bike use - his system is crap and im looking to spec out a new one from the ground up but i don't want to stress the charging circuit

[@AxeAlchemy]

I have a 2021 road glide limited, installed speakers and an amp, I couldnt find the rear speakers harness to plug into the amp. Where are the rear speaker harness? I definitely need a book.

[@buch-ie5jp]

Hey man appreciate the video!! I have a 2015 ultra would I need my radio flashed for the amp? Thanks for the help! And safe riding

[@sikbaggers]

You dont have to have it "flashed" but it helps with flattening the EQ on the stock radio so you can tune it with a DSP...if you dont plan on running a DSP I wouldnt worry about it

[@anubis68rh]

do you have a video for replacing rear speakers and running new wire in a 2014 Electra glide?

[@sikbaggers]

i sure dont ..im sorry

[@sethbillings1729]

Which of the line output converter do I need? Going to run 6.5 prvs in the fairing and 6x9 prv in bags. 2 channel? 4 channel? Remote turn on circuit? Thanks for the input!

[@sikbaggers]

Get this one..PAC LOC www.amazon.com/PAC-LP7-4-4-Channel-Output-Converter/dp/B00F0YCK0E

[@sethbillings1729]

@@sikbaggers thanks man!

[@sethbillings1729]

@@sikbaggers one more question, is a flash nessassary?

[@mth2068]

So with adding a amp to factory stereo you don’t have to get system flashed? When do you need Harley to flash the system?

[@mrbrad3236]

Is there a video anywhere that will show me how to wire that particular line output converter

[@sikbaggers]

not any videos that im aware of but its pretty easy...here are the instructions from PAC...catalog.pac-audio.com/index.php?controller=attachment&id_attachment=40 but all you need to do is take the left speaker wire that comes from the radio and (thats your input from the radio) wire that POS and NEG to the Grey POS AND NEG on the PAC...the same thing from the right side of the radio to the WHITE POS AND NEG of the PAC.

[@mrbrad3236]

@@sikbaggers Thank you sir

[@mrbrad3236]

@@sikbaggers This may be a stupid question but I'm kind of remedial to the wiring game but what powers the Pac? I do appreciate your patience.

[@jonathonwilson5998]

can you use the converter for front and rear speakers like i have on my ultra classic? thanks

[@sikbaggers]

yes you can

[@youdelmphotography2820]

Hi Steven great video. Question I'm upgrading my audio system in my 202 street glide special with new Boom Box radio, my Amp already comes with high line inputs foe each channel, How can determine which wire from the oem speaker wire is positive and which is the negative?

[@sikbaggers]

The larger spade on the bikes wiring will be positive ..but a simple test can be done to find positive. if you have a volt meter, put it on AC volts and touch it on the speaker connections to find + and -. If you get +12v that is correct, if you get -12v that is backwards. This will help you identify + and - on the speaker.

[@petedonna4894]

Great video and instructions, thanks. One question, why does harley say you have to flash the radio. Is that necessary?

[@scottford3504]

I’m wondering the same. When do you need to flash the factory radio?

[@motorcyclessoundsystems-mi2785]

Factory radios on 2014 and newer Harley-Davidson audio systems use a “high fidelity” EQ curve. This EQ will cause excessive distortion with any amplified audio upgrade and will lead to speaker damage. Hence, “flash” your factory radio to remove this EQ. This has to be done with special equipment and by a shop who know, like us. @t @t @t

[@williamwirtkayaksarge485]

Do you do the flash before you install the amp and speakers or after?

[@petelanzone484]

@@williamwirtkayaksarge485 if you install the amp and it is not yet flashed. I ti will sound like crap. So either right before your start the project or right after you are done.

[@RydinginStyle72]

Do you have to get the radio flash using that line output converter? Also will that line output converter work with sound digital amplifier?

[@sikbaggers]

Having your radio flashed will flatten the outputs creating better sound for your amplifier to work with. however you do not have to do it.

[@davemiller1289]

I got a dsa1 Rockford mdp. Do the digital processor hook up before or after the amp. Thanks for answering my questions. Love the video

[@eazye210210]

Where did you ground your line output converter to?? Thanks

[@sikbaggers]

Its best to run a ground back under the tank and ground it somewhere on the frame.

[@rickfoss1136]

Hey Steve thanks for all the videos. I installed the ss nano 1000.4 amp, and fairing and lower fairing speakers. Put bike back together and all worked fine. Took it to Harley to have it flashed and they looked at me like I was stupid because it wasn’t boom or RF. Told me they didn’t know what to flash it to. So I drove home! Wondering if you could steer me in the right direction on what to tell the HD service guy to flash it to! Thanks in advance

[@sikbaggers]

I have since found out they quit flashing radios unless its thier radio gear. The old "flash " was simply turning the internal amp off and also turning on the rear speaker wires that are under your fairing. If you have eveything hooked up now and its working just keep the bass turned down on the head unit, turn off the volume speed control and set your gains for your speakers and you will be fine. My SG had 10 speakers and 3 amps ran off the stock unit and it was fine. I never had anything done. I only suggested to turn on the rear channels but its not necessary

[@rickfoss1136]

I appreciate your timely response!!! Thanks again!

[@cigarettedan]

Hello @sikbaggers what is your current speaker and amp recommendation (with only 2 faring speakers) now 3 years later? I noticed a year or so ago you recommended a different speaker. Thanks

[@sikbaggers]

yes ive switched to the PRV 6MR500-NDY-4 amzn.to/44KF4kQ and pair that with a Sound Digital EVOX 800.4 amzn.to/44IQSUH

[@cigarettedan]

Hey thanks so much@@sikbaggers

[@mccluremetalworks4214]

Appreciate the hell out of the video,great tips!

[@sikbaggers]

Thank you Danny!

[@mccluremetalworks4214]

@@sikbaggers sent you a message on fb messenger

[@abwolfsto6039]

thanks for the step by step video straight to the point awesome video man god bless brother 👊👌also not a long waste time of video like other people do thank you.

[@sikbaggers]

glad to help! thank you for checking it out~!

[@scottgreen9129]

Hows the amp bolt on radio?

[@gccattle2606]

Real simple question before I take you're advice and try this install. My 2017 Ultra Limited has 2 Ohms speakers in the front and in the back. If I upgrade the wiring to all four speakers and install the new 8 Ohms in front and the 4 Ohms in the rear, I shouldn't run into any problem using the setup you're describing as long as I'm using my stock radio and I don't already have a factory amp installed. Would that be correct? Thank you for your time and the video's

[@bigebengals]

Did you do this?

[@chrisnorth2927]

Great how to video and love the links to all the specific items that is outstanding. Question the line leveler you use does it nullify the need to "flash" the harley radio that I've heard about? Would hate to do all this upgrading for it to not sound great

[@virgilschlorke9160]

Love the video and find it very helpful along with all the comments and questions -Thanks. I just purchased a set of AVB lowers with speaker pods for a 2018 SGS. I am planning to install DS18 Pro's in the lowers and switch out the upper fairing speakers to DS18 PRO also. I have a few questions if anyone would be willing to share; 1. Are the DS18 Pro's a good/best choice? 2. Should I get 4 or 8 ohm speakers 3. I am currently looking at the Rockford Fosgate TM400X2AD amp - is this a good choice? Thanks again

[@gmlees2005]

If you use the amp listed you don’t need the LOC it has speaker level high input

[@sikbaggers]

most of them do...High level input sucks...its worth the 25 bucks to get a LOC

[@gmlees2005]

I tried with the LOC but couldn’t get it to read the voltage like it was supposed to so I just used the high level input and it sounds 1000% louder than my factory setup

[@mrbrad3236]

On the line output convertor where did you run the yellow wire to?

[@sikbaggers]

Yellow wire can go to any key on wire..aux port works great...you will need to extend the wire.

[@ramirorodriguez7052]

Did you use marine speakers

[@crsddabc5568]

I’ve got a 2007 Electra glide classic, original stereo and two front speakers only. I’d like to upgrade stereo and speakers... POSSIBLY add two trunk speakers...$600 max budget. Can you advise (which brand)? I’m. guessing I’d have to add an amp if I go with the two trunk speakers... thanks for all you do. I’ve already successfully put lights on following another video of yours.

[@bigshoR1]

Hey Steve, first of all you definitely have the best looking videos and comprehensive list of diy stuff out there. I have a quick question... I already have some Infinity Kappa 62IX 6.5" 2 ohm...these should work good with the rest of your set up shouldn't they? Thanks for any and all info, love your channel man keep it up for us with thick skulls. 💀

[@sikbaggers]

Thank you Jeffrey..sorry for thr late reply...been down wit the flu for a couple of weeks. And yes the 6.5 kappas will work great..thats a great speaker. Just watch running 2 ohm speakers if you start adding speakers to them like in series...that will cause you to draw 1 ohm and then most amps are not 1 ohm stable.

[@leonardanderson8072]

Got a question. I have a 14 street glide. The kappa 6.5 ix flange was to thick. The speaker box side mount bolt holes wouldn't line up. How did you get them to line up?

[@aironsnowboards7534]

curious why u used a line out converter and not just take wires from speakers to high input of amp?

[@sikbaggers]

Factory stereo systems connected with high-level inputs will not sound as good as low-level inputs. If your using an aftermarket stereo, there won't be much of a difference between high-level or low-level inputs on basic systems. If you're going higher end use low-level inputs.

[@writer312]

Epic video!!! Would that same amount fit in a 21 RGS?

[@bigebengals]

General questions, first you have two different speakers listed on your link. I am looking to add two batwing fairing speakers and maybe later adding advant speaker lids? Will this amp handle both sets of speakers?

[@sikbaggers]

yes..one is 8 ohm and one is 4 ohm....it depends on your set up or what your final set up will be as to what ohm ou purchase. if you are going to 4 speakers I would get a sound digital 800.4

[@bigebengals]

@@sikbaggers Can I replace my factory passenger speakers also, 2021 Ultra limited with the same type ones I am putting in fairing?

[@bigebengals]

@@sikbaggers and thanks so much for your videos, nice to see someone take the time and explain it!!

[@larryvollmar8763]

I wish you guys were closer. I live in Michigan and can't find a reputable bike stereo shop. Anyone I talk to tells me I am screwed and need to drop about 2500.00 on my bike minimum...UGH

[@sikbaggers]

2500? holy shit I could deck you out with 2500 and you could do competitions...

[@larryvollmar8763]

@@sikbaggers I am not apposed to riding down to Illinois and getting a system put in. I just want clearer and a little louder then I got.

[@anubis68rh]

would a DS18 PRO-ZT6 6.5-Inch 2 Way Pro Audio Midrange Speakers with Built-in Bullet Tweeter, 4-Ohms be a good choice for a motorcyle

[@sikbaggers]

you would have tro butcher your pod pretty good to get that rubber surround on that magnet in there to fit. Its a decent speaker but its marine grade and these pods wont usually fit PRO Audio Marine Grades like that

[@lcoreywood3607]

Awesome video. Very very helpful. Subscribed!

[@RafaelJimenez-hz9gu]

Sir, when you install an amplifier do you have to flash the stock Harley radio? Thank you.

[@shawnberger8099]

Would a 2017 street glide be the same for the most part?

[@chrisgunter4344]

Hey Steve....another great video....aren't those speakers mids? Wouldn't a pair of tweeters keep them from sounding a little flat?

[@motorcyclessoundsystems-mi2785]

That is correct. www.motorcyclessoundsystems.com/ facebook.com/MotorcyclesSoundSystems/ instagram.com/motorcyclessoundsystems/

[@rafaelcasero2822]

Hi Steve have several questions and cannot find a utube that is specific to it... 1 - Do I have to use the Power Yellow and the Remote Blue cable if my Amp already has it ? Meaning all I will need to connect is the Speaker wire. 2 - I have the PAC LP7-4 L.O.C. PRO Series 4-Channel device, I'm only going to tap in the front speakers, so I will use 2 channel on the PAC, can I just twist the other two channels together ? Meaning I will use the White and Gray for the 2 channels, can I just twist the Green to the White and the Purple to the Gray for all 4 channels and then go all 4 channels to my amp RCA ? 3 - The the Gain on the PAC will only have the adjustment on one side which is the Right and Left Rear Or Front ? or would I need to adjust both Gains to the same ?

[@jameswilson6976]

I have a street glide special do I need to flash the head unit for this install

[@bradleyheady3145]

Did you tie both the remote wire for the amp and remote for the LOC into the aux wire?

[@sikbaggers]

yes..you can do that.

[@potato7600]

Will this same setup work with a 2018 ultra classic

[@EricCampbellflight836]

I have a 2018 Electra glide Police edition. It did not come with a radio wording harness. I have a stock radio I’d like to put in it. Will a street glide harness work ?

[@steveneubert3061]

So I got a question; with the AMP connected directly to battery will what will keep the AMP from drawing down the battery?

[@Knight_Glider]

The amp won't start drawing power until the remote wire sees power to turn the amp on.

[@chrisakadie]

I bought the aquatic av head unit its a plug in type now I ran all my speaker wire I put my new speakers in my new amp and new head unit the one thing I'm confused on is what do I do with the old speaker wire that was hooked up to the old speakers I believe I can just cap them and not use them because it was hooked up to the old wire harness but now that I'm by passing it with the amp I'm sorry if its a stupid question I'm new at this

[@sikbaggers]

you are correct ...you can just cap those off...We usually dont remove any factory wires..just cap them in case down the road you or someone else may need them they are still there.

[@vinnypandolfo6195]

Why change the speaker wires? What did that do to make the installation easier or better?

[@sikbaggers]

heavier gauge wire for the bigger amp...stock is 12. Use any online chart to see how much your amps is pushing vs how long the wire is and itll show you the gauge you need.

[@vinnypandolfo6195]

@@sikbaggers Thanks! Fantastic information!

[@gillesclavet5543]

Good video..i have 2011 Electra glide..any recommendations on a stereo system with amp? Thank you

[@sikbaggers]

The 2011 more than likely has the 5.25 inch fairing speakers, start there by getting some 5.25 to 6.5 inch speaker adapters off amazon for about 20 bucks...upgrade to a pro audio 6.5 speaker. PRV, Ground Zero, DS18 etc about 200 for a pair is a rough price on pro audio. ....get a Sound Digital 800.4 EVOX 4 channel amp. This is a pretty basic major fairing upgrade from what you have in the bike now. Those speakers are about 35 watt speakers...the pro audios will be around 200-300 watt speakers...you and your passenger wont have any trouble hearing this set up at 70mph half volume.

[@mrbrad3236]

Will the amp you installed power four of those speakers? Might be a dumb question but had to ask looking to add two more of those DS18s. Your videos have saved me hundreds if not thousands of dollars. I appreciate you sir.

[@sikbaggers]

yes sir you can push 4 speakers with that amp...4 channel amp so you can bridge it for nearly twice the power to run 2 speakers or just run 4 speakers at the normal wattage

[@duke9173]

1/2 the time is getting those bottom screw out and back in.

[@sikbaggers]

yes..they suck...after doing a crap ton of them now its like second nature although Is till hate it lol I dread that part.

[@CodyMcDonald89]

does this also work for new newer harley GTS radios as well? im wanting some better sound but not 2k plus worth really.. thanks

[@sikbaggers]

Yes it is the exact same concept regardless of the radio

[@jeffherrera485]

Hey thanks for the video. How did you mount the amp to the tray in the fairing? I got the same setup but I cannot figure out how to best mount that amp since its too big to sit down in the tray.

[@sikbaggers]

i use tool box liners from any hardware store...cut it too fit so there is no vibration between the amp and tray and then big zip ties or double sided sticky velcro strips. You zip it down good and it wont move

[@Anthony-kj2vl]

Dumb question, but where do you hook the ground wire and power wire for the amp

[@sikbaggers]

Hook your power wire straight to the battery. You can run the ground to the battery but I prefer to run it to the frame ground where the battery is grounded. Follow the black wire down under your starter from your battery. There is a 7/16th bolt that grounds your battery to the frame. remove that (its kind of tough to get to) and add your ground wire there. To make it easier to get to remove your oil dipstick, and the starter cover. Its on the end of your starter and one single small bolt in the middle. there is nothing behind it..its just a beauty cover. then you can access that bolt much easier. I hope this helps.

[@Rvzoo310]

Is that an Advanblack inner fairing? I’ve heard they don’t line up well with the HD stock outter fairing??

[@rickyh78]

Sorry if this has been asked and answered…if I’m just planning on doing the 2 fairing speakers with the amp in your parts list do I go with the 4 or 8 ohm speakers?

[@sikbaggers]

hey now worries ill try to explain it...if you get a 4 channel bridgable amp you and get the 8 ohm speakers and bridge the amp to 2 channel....meaning using all 4 channel on 2 speakers..that would bring the load down in half..from 8 ohm to 4 ohm draw from the amp. The amp should be 4ohm stable bridgeable amp. Adding more speakers later will effect this though. So make sure you only want the fairing speakers and never plan on adding more..if you do you will have to change the amp more than likely. There are a ton of variables that come into play.

[@Joe_1971]

When you mentioned the streetglide having 3 amps and 10 speakers...how does the charging system handle the amplifier load?

[@sikbaggers]

It handles it great...same set up on my RG with even bigger amps and no issues. Upgraded battery to a EarthX lithium

[@Joe_1971]

@@sikbaggers I figured 3 amps and more than likely 30 amp fuses on the amp gives you an idea how much current each amp will pull...figure around 20 or so amps each plus the bike itself lights ignition etc...i figured that stock charging system is getting taxed big time

[@gudynielsen8780]

Hey.. Any problems with amp not turning on when bike is started???..Sometimes😏

[@sikbaggers]

no, not at all...check your remote wire and make sure it had a good connection...then check your ground..these two things can cause that

[@MrMarvin3180]

should I get my radio flashed before I start hooking up the amp and speakers to my stock radio? 2020 road glide special

[@petelanzone484]

@Jeff Burgess Its your choice but it will sound like crap if its not flashed and you already have the amp installed. Another words if you do it after do not play it long or loud until that has been flashed.

[@LeJeansJewelers]

Have you ever installed the new 400 amp RF in the saddlebags like HD specs? Mine was installed by dealeship and has come off twice ( the amp)

[@sikbaggers]

Ahh no I have not...I tend to stay away from anything RF outside of their Digital Sound Processor.

[@coreyjones6537]

I did a similar install on my 2013 using the same amp and am getting terrible FM interference when I go over 1/3 volume. Any suggestions? Great video, made me a lot more comfortable taking this on.

[@sikbaggers]

Do you have an aftermarket LED headlight? A cheaper aftermarket headlight can cause interference and also a bad ground. Check those.

[@dannypierce3520]

Hey Steve! Great video! You’re definitely helping us bikers, all over the world, build more confidence in doing a lot of things ourselves now! One question, I’m wanting to junk my Boom Audio Stage II speakers on my 2019 RGS, and hook it up with all DS18 sound...what’s your professional opinion on the DS18 Pro’s? Very impressive sound quality? Would you buy it? Thanks in advance, and keep on slangin them vids brother! ✌🏼

[@sikbaggers]

Thank you Danny...Much appreciated. The ds18s are a solid choice for the price rage for sure. They only issue I have found is there are no 8" mid bass speakers for the 8" lids. Now that being said adding anything that can handle bass is fine...in the parking lot. Riding down the road youre not going to hear that bass at all. So adding a a decent set of 8ohm speakers and getting a 4 ohm or 2ohm stable amp so you can bridge the amp and add more power to them is the best route for a clean, loud sound.

[@hanzkanz123]

Great video Steven. Is it possible to install further two speakers for the lower fairings with this kit? Thank you in advance. Hannes

[@sikbaggers]

If you install a 4 channel amp you can run the front as front and the lowers as rear.

[@domingorivera1359]

Do I need a converter to add an amp?

[@billhowe4130]

With installing this system did the factory radio need to be reflashed? I have a 2020 street glide special

[@sikbaggers]

Doing it this way will not require anything to be flashed...however if you want a cleaner "flattened" sound you can have them set it to 4 channel no amp...thats all the flash is...they plug it in, go to the drop down menu and select whatever they want and it sets the audio out levels on the radio....That being said I have never had one flashed. And using the right amp and speakers you will have a huge improvement over the stock harley junk.

[@jloeza3218]

Are the speakers used water resistant or marine grade?

[@nietolkj]

Can you install an amp and speakers like that on a 2020 road glide? Also without flashing it after install

[@sikbaggers]

yes, When Harley used to "flash radios" all they were doing was using a drop down menu to select what channels are turned off and on, flattening the EQ and or turning the eternal amp on or off. We used to flash them 4 channel, no amp. This would turn on the rear channels that are already on every bike but usually not turned on and also turn the internal amp off. You can still do this even though harley quit flashing radios. Just split your front channels and send those signals to the LOC and come out 4 channel RCA to your amp

[@jameshorton6417]

I have a 2020 Road Glide and would like to know how your audio upgrade/install worked out for you.

[@MrAyarza]

Hi there, I’ve the 2014 Ultra Limited with rear speakers.Can I install a 4 channel amp and follow the same procedures as the front speakers? Thanks for your videos, very helpful

[@sikbaggers]

Hey thanks man.,.have been into you fairing yet to see if you dont already have a small amp in there? Not sure if the stock 4 speaker bikes already have one or not. But in any case if you do not you certainly can do this and add one...convert the 4 channels from the radio with the LOC and then add your amp, come out of the amp and run back to your 4 channels of speakers.

[@sikbaggers]

@@MrAyarza just a 4 channel LOC

[@sikbaggers]

@@MrAyarza that amp has high level and low level inputs...the high level is basically what you use when you don't have rca but they sound like garbage and I don't recommend that route. If you look at the wiring diagram for that amp there are 2 plugs that go from the side there that have rca on the other end. Maybe 4 inches long. Plug those into the amp. Then you have low level input rca which are far superior in sound. Here is the link. Download and go to page 7 ..you will see what I'm referring to. Its basically pigtails with Rca inputs..so it would go from radio,l to LOC to these pigtails which plugs into the amp. www.rockfordfosgate.com//rftech/library/2017/03_amplifiers/1230-60375-01-b_pbr400x4d-man.pdf

[@MrAyarza]

SIK Baggers Awesome! I really appreciate your help, with out it I wouldn’t even tried to remove the faring. Thanks for helping us, you rock

[@sikbaggers]

@@MrAyarza Youre very welcome...if you have any questions when you get in there please let me know.

[@jamessmoth8683]

My bike already has the boom audio II system front and saddle bags 2 amps, came with the bike. What can I do about upgrading just the speakers?

[@sikbaggers]

Im not much of a boom audio guy but you can check your specs on your amps and try to stay in that spec range for your speakers. You want to stay in the watts and ohms range of that amp. I would say any pro audio speaker will be an upgrade form the boom stuff...Ive torn out a lot of boom audio...thousands of dollars worth and replaced it all with new amps and speakers..but if you are wanting to salvage the amps just find out the specs and stay in that range and pick a better speaker