Heather and I are installing a loading dock leveler at HTP using their equipment.
Пікірлер: 79
@waiakalulu35013 жыл бұрын
I'm loving my lunch box welder from HTP! Using it now to weld a new hitch on my trailer. If I could do it over again, this would have been the first welder I bought. It welds like a dream. I have multiple welders, but this one is my go to, because it's so simple to setup!
@chrisplayz2535 жыл бұрын
It's good to see a channel with such a large variety of projects. I'm slowly working my way through your videos, learning a lot as I go along... thanks for the content dude!!!
@ZILAwelds5 жыл бұрын
thanks for watching !
@turbocobra7 жыл бұрын
Nice work sir, good to put the HTP welder to use on an HTP project!
@ZILAwelds7 жыл бұрын
Thanks
@FreeRV2 жыл бұрын
Hi 👋 friend! I see you used to have first generation of sprinter! Great 👍 job on weld seam and music 🎵 thank you 🙏 Have a good weekend with hart
@jagboy697 жыл бұрын
Thanks... Now my Invertig is missing "home" Tell Jeff, J in texas says Hi! Saw him on the lift for about 2 seconds and the back of his head welding. Super guy.
@BigHayes77716 жыл бұрын
You can use the hammerdrill itself with a blunt bit to drive the anchors into the hole
@ZILAwelds6 жыл бұрын
chadwick hayes absolutely you can ! And when i have to put 30 or more anchors in i usually do that too .... if its only a hand full or 2 hands full of anchors i done mind driving them in by hand
@BigHayes77716 жыл бұрын
ZILA totally agree, just never see it done on KZbin love the channel
@boneyfreak91975 жыл бұрын
Worked on those before. Seen a lot of weld breaks where there's undercut of the base material after the fact like the welding done in this video. Maybe a 2nd pass or FCAW should be used to get proper fill and penetration. Those humpback welds are just blobs on metal with little penetration.
@ZILAwelds5 жыл бұрын
boneyfreak - WELCOME TO THE CHANNEL i am glad you were able to identify you (let me quote you) "humpback welds". congratulations - you are the first guy to do so. This dock leveler is up and installed now for well over a year - at 5-10 trucks being loaded and unloaded daily with a 9000 lbs forklift and up to 4000 lbs cargo on the forks and boy did we sure get lucky - it is still holding up believe it or not !!! btw - the dock leveler right next to it was install about 6 years prior in a similar fashion .... and we must have gotten really lucky on that one !!!! because that one is still holding up too ! no welds cracked - nothing re welded nothing needed to be fixed in any way sort shape or form ...... but sometimes it is just better to be lucky than to be good. i hav heard of really good welders and then they found a guy who was better than them ..... but i never heard of a real lucky welder and someone came an out luckier him ....
@mrgreenswelding28537 жыл бұрын
nice job Peter and team!!
@ZILAwelds7 жыл бұрын
Mr. green thanks Sharn
@ajsironworks39377 жыл бұрын
What type of electrodes were in the box and how many amps were you set at on the vertical welds?
@ZILAwelds7 жыл бұрын
Adam Johanson in the yellow box was a maintenance rod with a cellulosic based coating 1/8" 100 amps vertical down In the white and red metal tube was lincoln excalibur 7018 1/8" 120 amp and 125 amp with pulse vertical up ( more on the flat)
@franksmodels297 жыл бұрын
Great vid👍🏻👍🏻👍🏻great to see working in the field and not in the workshop 👍🏻👍🏻👍🏻
@ZILAwelds7 жыл бұрын
Frank yazzetta thank you! I try to do a fair share of field service videos - there are a few challenges with that.... 1) not every customer lets you video tape and publish the job 2) it needs to be a flat bid job - cant be hourly because with videotaping everything takes twice as long ( and of course the customer does not want to and should not have to pay for that ) 3) right now business is good - we are working 12+ hrs a day even without video taping .... and seeing it takes so much longer video taping and editing - i have to make a business decision - make money or make a youtube video that i make about $20 on over the next year .... So i try to make videos as i can....
@franksmodels297 жыл бұрын
ZILA I can understand that, nice to see it out here keep up the great work and vids 👍🏻👍🏻
@joto28754 жыл бұрын
I wouldnt be surprised if yall had to go back and install a transition plate as well, overall good work
@ZILAwelds4 жыл бұрын
Thanks - we got lucky - forklift makes it just fine without a transition plate
@lukejackson94184 жыл бұрын
Question?? Is it easier to install the bumpers first? Then the Loding dock. Or either preference is fine
@lukejackson94184 жыл бұрын
Strictly a welder but 6011 I find to work better on horizontal
@ZILAwelds4 жыл бұрын
it does not matter to me - its a matter of measuring and layout ... whatever works bet for you
@ZILAwelds4 жыл бұрын
6011 runs good downhill .... 7018 needs to be welded uphill no matter what
@leifberner5 жыл бұрын
Pretty Welds, Love the cutter! Gap between the bumpers and the EOD deck is too wide. There could be an injury when someone steps in it. Look at the gap between the bumpers and the EOD on the left dock it looks to be correct. Did you do this on purpose so you could make another video showing cutting out a plate and adding it to eliminate the gap?
@ZILAwelds5 жыл бұрын
Leif Berner the bumpers need to be where the bumper need to be! They line up with the truck. They are identical between left and right side ( the bumper spacing is identical) The left dock has a 72” wide leveler the right side had a 60” wide leveler Thank you for voicing your concern - looking at what i just explained i can not share the concern. If i would move the bumpers closer together i would damage the truck
@marcogarcia46967 жыл бұрын
Good job Peter...i see in this video you were using a htp plasma cutter and i'm assuming is the microcut 875 sc By any chance can you please make a review video of the htp plasma cutter . Thnx
@ZILAwelds7 жыл бұрын
its coming - i am getting a 4x4 cnc table for it also ... there will be an entire series of some hand and a lot of cnc plasma cutting with that cutter coming ... the table is about 6 weeks out - so in 8-10 weeks the videos will be rolling in - thanks for your patience
@marcogarcia46967 жыл бұрын
Thnx Peter... Looking forward to . You and Chuckee are one of the best in welding tips and info , keep rolling those awesome videos , Greetings from Aruba .
@ZILAwelds7 жыл бұрын
NO you have this all wrong - Jody is the best ! I just do different stuff than most other guys do ..... and for me my welding business is my job - the videos are my hobby .... if you want to see the best Stick/Tig welder i have seen so far on youtube look at my buddy Travis channel kzbin.info/door/NsfFIfIBwHtA7ZTMTkJMlwvideos He does crazy stuff that Mr. Tig and some others can't even dream of ! and you know what - he makes his money welding - videos are just a hobby for him ... But thanks for watching ! and thanks for the support
@marcogarcia46967 жыл бұрын
Lol ...i know that Jody from welding tips and tricks is one of the best , and there are many of good welder / fabricator out there making videos , i'm a welder fabricator my self and also have a small shop .. just complimenting you guys.
@meganbrennanmurphy14726 жыл бұрын
marco garcia s as weldi
@0ohoaxo04 жыл бұрын
Those block are going to snap off if not anchored at the bottom hole. Swiss cheese concrete and youre using wedge anchors?! Nope
@tedsoares31594 жыл бұрын
Thats a homeowner unit from vestil < Those people installing the equipment dont have a clue .? Leveler is installed first. But first the angle their installing to is not worthy to hold a EOD it was rust deteriorated and needed structural support under bottom half was home depot blockouts. Find something else to weld in your garage?
@Mikefence7 жыл бұрын
finally real pro channle
@ZILAwelds7 жыл бұрын
why? heather welding ?? LOL Thanks - i take it as a compliment
@butchmcintyre51966 жыл бұрын
install your dock in place first then install your bumpers I have done this work a lot . one bumper is out of square
@ZILAwelds6 жыл бұрын
so ope that side it would have worked the way how you tell me - on the left side (that dock was installed years ago ... once the dock is in - you cant get to the bumpers any more (with weld) not outing ) because the other dock is wider ... and initially this dock here food have been the same with - but they shipped one that was 6" narrower ... so on this one i could have done it the way how you say ... i don't think welding the bumpers and the dock plate to the angle in the concrete is "proper procedure" anyways.....
@lsellclumanetsolarenergyll50716 жыл бұрын
Nice job. so I am guessing they had 240V on site :-)
@ZILAwelds6 жыл бұрын
single and 3 phase ... 60 amp ... imagine that ... LOL
@lsellclumanetsolarenergyll50716 жыл бұрын
gosh still can't get used to those stupid 3 phase crap here in the US. Back in Germany you start with 240 and when you do Dual you are already at 480V hmmm when do they catch up here in the USA???? Never ??? LOL
@DirtyBikerbits6 жыл бұрын
Does anyone know if htp has a dealership in Australia yet?
@ZILAwelds6 жыл бұрын
DirtyBikerbits they dont sorry
@DirtyBikerbits6 жыл бұрын
ZILA gutted! Thanks for the reply!
@nicola83597 жыл бұрын
Hello.... Htp is manufactured on italy under the name stel?
@ZILAwelds7 жыл бұрын
Some machines are - others are not. Which model specifically?
@nicola83597 жыл бұрын
Thanks was simple curiosity!
@mikemcdonald84947 жыл бұрын
what helmet are u running mr.zila never seen it
@ZILAwelds7 жыл бұрын
This is an HTP Sticker CSV it is a few years old - i believe they don't make it anymore - and because i didn't like the headgear i switched it over to a Jackson safety 370 head gear ..... i personally don't like automatic welding helmets much ... i think they are good for cutting or tack welding If precision welding matters i personally prefer a Jackson Halo shell with a fixed shade 9 or 10 real glass lens gold coated ..... the clarity of the image and the even tint is hard to beat ..... if you are looking for an automatic one - if mine would go bad today - i would probably buy an HTP Sticker XXL .... i like it a lot (as much as i can like automatic hoods :-)
@mikemcdonald84947 жыл бұрын
very nice sir adapt and overcome, true welder way... keep up the good work and have fun
@thebrokenbone7 жыл бұрын
damn i deleted the reply haha well here again, thank you peter for taking your time, i`ll get the small one bc i have to make a zillion 13mm anchor bolts in an upcoming job and i trust your advice (on welders has come extremely well !). hope it comes with some sort of dampening for my wrists :). oh, i`ll take your advice on the hair too... ppl are asking crazy money for haircuts these days :D. take care. pete ps my gf teaches german at the local goethe institute, i showed her the shotgun video and she`s still laughing.
@ZILAwelds7 жыл бұрын
13mm ... that is not very challenging .... i once drilled about 200 1/2" anchor holes in concrete 6" deep each in a day ... my hand were not numb at the end of the day .... that thing laughs about 1/2" bit ... even if you hit a piece of steel re enforcement in the concrete ... typical it drills right through it
@thebrokenbone7 жыл бұрын
200!! man that i`m sure i could not do! i broke my wrist in a mc accident years ago and it has made my life a bit hard, now it swells up if i abuse it... and age (why lie about it haha)
@JohnSmith-iz8wg6 жыл бұрын
That must be Heather's work uniform.
@ZILAwelds6 жыл бұрын
John Smith it is !!!! 😜👍
@thebrokenbone7 жыл бұрын
hallo peter nice haircut :D what hammer drill are you using? thanks for sharing man. take care. pete
@ZILAwelds7 жыл бұрын
p penca bosch .... something ??? It has SDS MAX bits Its like $400 at menards .... its a good drill for this stuff If you want to know the exact model i can tell you later
@ZILAwelds7 жыл бұрын
p penca the haircut - was only partially by choice .... i was doing some overhead spray foam insulation and found out : over head welding is a lot easier than overhead spray foam insulation .... its better for your hair too 😂😜
@thebrokenbone7 жыл бұрын
oh yeah (if it`s not much bothering you) and thanks again, i`m in about to buy one and the varieties are mind numbing, ha! much like welders (but that i know a little :D)
@ZILAwelds7 жыл бұрын
The hammer drill is a Bosch 11240 - which i have just learned is discontinued the model that follows it is a Bosch RH540M I like this hammer for medium duty work ..... i drill a lot of 1/2" and 3/4" with it and some occasional 30mm (about 1 1/4") it's a good medium duty drill ..... if you are looking for something more and if you want to use core drills bits ..... i also have a bigger one - the bigger model got replaced with RH1255VC now THAT is about 3 times the money - but drills 5" core bits just fine :-)
@zealthsteel75425 жыл бұрын
What was the bid on it please
@ZILAwelds5 жыл бұрын
Zealth Steel with drive time this job was 4 or 5 hrs .... and whatever your hour is worth depends on where in the country you are located ... some guys struggle to get $50 per hours others get $150 per hour ....
@giovanni29805 жыл бұрын
ZILA I make 20$ an hour doing this lol but I’m just an employee for my company
@schultheissfarm49894 жыл бұрын
Hes good
@manivannans27656 жыл бұрын
Super work bro installing rate for s m s please give me
@ZILAwelds6 жыл бұрын
Manivannan S you mean how much the job is worth? All depends on where ( which city and state) it is The customer supplied the parts I call this a 3 ( for sure no more than 4) hrs job .... multiply that times the “going rate” in your area .... anywhere from $75-$150 per hour .... than add some travel time ( depending on how far you had to drive ...) Just to tell you a number - where i am - this would be a 4-500 all in ( travel, generator fuel, cut iff wheels, welding supplies and labor ...)
@AfroMyrdal7 жыл бұрын
Duuude, why you not called "Peterbuilt" ? :p guessing youve never heard that one before :p
@ZILAwelds7 жыл бұрын
its a Heather and Jeff build ... :-) i just video taped and did some demolition work
@braulio13507 жыл бұрын
Correct title would be installing a edge of dock.
@ZILAwelds7 жыл бұрын
Thank you for watching and thank you for enlightening me.
@ZILAwelds7 жыл бұрын
i guess the manufacture call it a dock leveler kzbin.info/www/bejne/baurZ3mod959h5o
@braulio13507 жыл бұрын
No, the manufacture called it edge of dock leveler better known as(EOD). A dock leveler is different in which give more workable adjustment range for fork truck.