Installing metal roofing around a valley ending in a roof.

In this video I’m showing the best way I know of to install metal roofing around a valley which ends into another roof, for example this roof has a small open garage roof running into the main house roof.
Here are some of the tools we like to use, these can be found on amazon via the following links;
Left off-set snips: amzn.to/3uJD5kF
Right off-set snips: amzn.to/3NcSpMS
Edge roller: amzn.to/3GtsBs6
The caulk we Love to use (super strong!!) amzn.to/3GzyF2r
18” hand break: amzn.to/3GrB0wn
You can also get this in a 24” length for Hemming the bottoms of valley angles on standing seam.
Our favorite gloves: amzn.to/3T5jp4R
Our favorite roofing Shoes: amzn.to/482YyU4
(AKA) Hiking Boots)
Power Metal Shear: amzn.to/46IIh5B
Impact driver: amzn.to/3t26iqn
Hand Break 6”: amzn.to/3R6uiRb
Hand Notcher to notch the bottom edges of your standing seam panel for Hemming the bottoms if they don’t come pre-notched from the manufacturer: amzn.to/3Tbl88K
Rubber Mallet: amzn.to/46HAk0A
I am an Amazon associate, and may earn a commission if you purchase any of the products using the links I have listed in the description.

[@dmc_cat]

Thank you! So helpful. Ran into this situation and didnt know how to solve it until watching your video.

[@plankroofing]

Glad it helped!

[@Shivs1989]

nice! clean simple and to the point

[@gogo12able]

thanks for video just fixed a really bad leak , and all because of this mistake they did trying doing one piece in this section , now problem solved saved my boss lots of money , other companies trying to charge thousands of dollars 😅😅😅

[@aaronaldrich1546]

Classic rib panels are a pain in the arse for such details. This looks great

[@ohthatguy4644]

Thank you!!! Looks great as well

[@jimimmler9110]

That is exactly the detail I need to create in just a few days. Since I have a very shallow pitch I am sure hoping that the location of the standing seam cooperates with the valley flashing.

[@plankroofing]

If you are unsure you can measure to make sure the valley point comes out between the ribs. If it doesn’t you can rip a sheet to make your starter the right width so that it comes out right.

[@jimimmler9110]

@@plankroofing thanks, yes I’m going to plan to do that. This standing seam seams to repeat at about 11 7/8 intervals. I’m going to have to join a bunch temporarily in order to get an accurate measurement. Also I’m hoping that a vent penetration further along the roof will also cooperate to avoid a seam.

[@alexandersnyman2625]

bro actually put screws into the pan

[@gigamakaridze8404]

what happens when you connect two off-level roofs together? how to make everything covered with metal? do you have that type of video? please!

[@Gustavocontreras-w3o]

Is good I looking for job I have experience for 15 years

[@johnhardy2702]

Did you just lay the metal roof on asphalt shingles?

[@plankroofing]

No, We put 1x4’s on first, if you lay it on shingles it will scratch the metal from expansion and contraction. Also the 1x4’s give your screws more to hold. If you only screw into plywood or OSB your screws will back out and cause leaks. Unless you use the larger shank screws designed for Plywood.

[@davepaints101]

You can use rino shield over the shingles if you don't want to strap it just use the longer screw.

[@xxROEVYxx]

@@davepaints101 eh….just throw furring strips on. Good for a piece of mind.

[@Johnf1906]

That is wrong that seam is not supposed to be there

[@BrianKrahmer]

he mentioned that he believes it's the most waterproof way, and i believe he is correct. if you have a better way, please share

[@plankroofing]

I know, I don’t really like the way it looks but you want your roof to be leak proof and this is the best way we have found to do a corner like this.