Installing OTTP Delrin/Stainless leading control arm bushings, Cobalt SS

  Рет қаралды 3,404

Jason Widdowson

Jason Widdowson

Күн бұрын

Пікірлер: 11
@SimbaUchihaa
@SimbaUchihaa 2 жыл бұрын
Good video I can finally see what this install looks like
@simonriddick
@simonriddick 4 жыл бұрын
Cool. I have a 2008 SS that I daily and it has had that low speed clunk as long as I've owned it and I think it might be the bushings. I don't see any damage on the end links or sway bar bushings like everyone says pm the forums. There's a rattle coming from the steering column too I saw a video of the plastic insert that comes loose or wears out. I don't exactly have a press will have to figure something out. I noticed too on some of these control arms on rock auto there are 3 bolts on the end and some have what looks like rivets. Just looked mine is FE5 so non removable ball joint.
@jasonwiddowson8892
@jasonwiddowson8892 4 жыл бұрын
My 07 sc had rivets to. They get drilled and punched out. New balljoint has bolts. But I heard people have problems finding the lnf ball joint. Be careful there is a slight thickness difference so make sure they are fe-5 ball joints.
@simonriddick
@simonriddick 4 жыл бұрын
@@jasonwiddowson8892 I was reading that people just buy the whole controls arm rather than trying to find that ball joint. Maybe I'll just rock it till the wheels fall off :P :). Good to know though. Good that they have bushing kits though at least if it gets really bad i'll change it all out. Not much room to work there even those sway bar bushings are right up in there.
@miasma19
@miasma19 4 жыл бұрын
@@simonriddick i know Tom at Crate Engine Depot sells the fe5 lnf arms with options for both ottp cabs installed. Just email them, he will get back to you quick.
@dissectionproductions8783
@dissectionproductions8783 3 жыл бұрын
Check your intermmediate steering shaft
@SimbaUchihaa
@SimbaUchihaa 2 жыл бұрын
Thay intermediate shaft snuck on me, the wheel would start making these churning noises
@miasma19
@miasma19 4 жыл бұрын
Thanks for the video i am getting ready to do ottp bushings. How are they holding up?
@jasonwiddowson8892
@jasonwiddowson8892 4 жыл бұрын
Great I know they're new rear cabs have a lifetime warranty. I have no complaints it's a great upgrade
@miasma19
@miasma19 4 жыл бұрын
@@jasonwiddowson8892 sorry i took so long to get back. Thanks for the reply. Any special instructions for my installer? I am doing both Tcabs and Lcabs.
@dirtysouth_6787
@dirtysouth_6787 5 жыл бұрын
Keep them coming
Change Suspension Bushes without a Hydraulic Press?
10:36
Lock your Hubs 4WDing
Рет қаралды 195 М.
How to Replace Control Arm 2005-2010 Chevrolet Cobalt
14:14
Cheerleader Transformation That Left Everyone Speechless! #shorts
00:27
Fabiosa Best Lifehacks
Рет қаралды 16 МЛН
Support each other🤝
00:31
ISSEI / いっせい
Рет қаралды 81 МЛН
Quando A Diferença De Altura É Muito Grande 😲😂
00:12
Mari Maria
Рет қаралды 45 МЛН
Removal and Installation of 2009 Chevy Cobalt Lower Control Arm
14:54
Chevy Cobalt SS sc rebuilding your intake manifold
7:38
Jason Widdowson
Рет қаралды 3,6 М.
Cobalt ss M62 vs H62 vs TVS1320
8:01
Jason Widdowson
Рет қаралды 19 М.
How To Replace Worn Control Arm Bushings
17:39
HumbleMechanic
Рет қаралды 284 М.
TOYOTA CAMRY -replacing bushing control arm
10:07
ALI FIX
Рет қаралды 26 М.
CHANGING VALVE GUIDE SEALS WITHOUT REMOVING THE HEADS
10:26
20 Minute Chevy Cobalt Lower Control Arm
19:31
Brian E. Niskala
Рет қаралды 5 М.
Synthetic Grease Better? Let's Find Out!
10:10
Project Farm
Рет қаралды 515 М.