INSTALLING PRO TAPER BARS ONTO MY MT-07!

This video is a Step By Step on how to fit Pro Taper Bars to your MT-07 (Mine are CR Highs). This is the first time I have done something like this and it was a lot easier than I thought. Big shout out to ‪@TARZANMotoVlogs‬ for helping me get it sorted. Hope this video helped you out, see Step By Step guide below. Make sure you Like, Comment & Subscribe!😀
CR High - Pro Taper SE Seven Eighths Handlebars: www.dirtbikexp...
Step By Step:
1) Firstly remove all handlebar components
- Loosen bolts on left bracket that holds clutch lever
- Remove switch gear on left side of handlebars
- Remove bar ends both sides
- Cut grips off of bars
- Remove throttle cable casing
- Loosen bolts on right bracket that holds brake lever
- Loosen switch gear on right side of handlebars
2) Now loosen bolts holding LED screen and hang it out the way on the right side of the bike
3) Loosen handlebar bolts so it moves freely
4) Remove throttle tube from handlebars
5) Slide left bracket holding clutch lever off of the handlebars
6) Remove bar pad and brackets from Protaper bars
7) Slide left bracket holding clutch lever and throttle tube on the right side onto the Protaper bars
8) Tighten handlebars to your riding position
9) Use masking tape and a marker to mark your drill points for the switch gear
10) Drill both drill points on each side of handlebars
11) Replace all components onto the Protaper handlebars
- Switch gear on both sides
- Right bracket holding brake lever
- Attach throttle cable casing
12) Install grips on both sides using Grip glue/ Hairspray
13) RIDE IT LIKE YOU STOLE IT!!!
Sponsorships:
www.armaspeed....
Join the community: www.braplife.c...
Socail Media:
TikTok:
Personal ~ / mr.brapz
BrapLifeClothing ~ / braplifeclothing
Instagram:
Personal ~ / mrbrapz
BrapLifeClothing ~ / braplifeclo. .
My Motovlog Setup:
GoPro: amzn.to/38VEtpC
Mic Adapter: amzn.to/3N1QtF7
My Mic: amzn.to/3x0h7IT
Comms Device: amzn.to/3GxvLue
Team Links:
TarzanMotoVlogs:
KZbin - / tarzanmotov. .
TikTok - / tarzanmotovlogs
Reece:
Tiktok - / reeceg95
Jewls:
Instagram - / kewljewlz__
KZbin - / kjcinemas
Sparko:
TikTok - / wh05_sparko
Disclaimer - WHOLE VIDEO IS EITHER FILMED IN MEXICO OR ON A GREEN SCREEN

[@dannyb9083]

isopropyl alcohol works good for getting grips on and only takes a few mins to dry off. I don't normally use glue. I find theyre super sturdy even without and it means I can get them off with compressed air.

[@mrbrapz]

Ahh nice, ill take a look! 😀

[@TARZANMotoVlogs]

i learned more in this video than i did in school 😎😎

[@FalconR73]

😂😂

[@mrbrapz]

I bet i'm the best teach you're ever had lol

[@Try2KeepUpK]

I drank a beer everytime you said nobbilybit and I blacked out woke up in jail they are saying I attempted to steal the declaration of independence

[@mrbrapz]

Hahahaha 😂😂

[@Karlrx31]

I just heard it while reading it in your comment 😭

[@BlackSlimShady]

That rough edge thing you're talking about is called being knurled.

[@charlottec491]

Looks really good! Bet it was smelling rather funky in there with the glue and hairspray combo 🤣😆

[@mrbrapz]

Felt a little weird walking out of that room haha 😂

[@TomDawson18]

this was very informative and i like that ya did what a few mechanics do in cluding my self and use what tools ya have at ya disposel it is like if i need a hammer and that is my tool box i will use a ratchet or somthing else like a screwdiver not the correct tool but gets the job done grate video

[@mrbrapz]

Whatever it takes to get the job done! Thanks for watching and commenting Tom! 😀

[@buckywylde6493]

I'm really not looking forward to swapping my bars. But I had to lay my 07 down. So now I'm forced into it.

[@mrbrapz]

It took me a while to get used to them but now I love them!

[@buckywylde6493]

Finally got all my replacement parts in for my bars. About to give it a go. Hopefully it goes smooth

[@patoslagos6497]

@@buckywylde6493update good sir?

[@disintegratev6951]

can someone hook me up with a link to the windshield that he is using?

[@krispewkrem3]

I had Pro Tapers on both my old MTs. They just felt really really low. Fun for stunting. But not comfy commuting. I had a 2” risers with some Carmichael bend. But it just sat too low.

[@mrbrapz]

Yeah I get you, I must admit it took me a while to get used to them. But now I have them I wouldn't go back!

[@alex.crf450r]

pro-taper all the way

[@mrbrapz]

Alllll the way! 😀

[@alessmuk6164]

It is batter protaper mini for Honda, fits prfect

[@jonnyslater9942]

No need to drill your bars. The plastic nobbly bits, as you call them, can be easily filed down. And no they never move once tightened, done it on multiple bikes.

[@mrbrapz]

Thanks for the info!

[@Shay_K05]

Looking good I was sceptical but it looks rly nice 👍

[@mrbrapz]

Thanks bro! 😀

[@AdamKlawonn]

Did the ProTaper bars move the riding position higher, more forward (more “lean”), or both? Curious what the effect is. Thanks for posting!

[@mrbrapz]

Makes it feel more like a dirtbike, more upright position and more control.

[@aldindubo]

Are these bars 28mm or 32mm thick in the middle?

[@phantomcraneflymusic]

Bro that bike is fucking beautiful

[@mrbrapz]

Thank you! 😀

[@jakeoutrider7644]

Heads up, next time u gotta slide stuff on and off, just lube the bar with dish soap. it dries eventually

[@mrbrapz]

Thanks for the tip!

[@stevenbolton5967]

What are the dimensions of the new bars what rise is on them towards your standard looking to get new bars but wanna keep the high

[@mrbrapz]

No longer have the bike so I have no idea, I hope someone can help you. 🙏

[@BackyardGoon]

I don’t know what one to choose on the site can you send the link to this one

[@mrbrapz]

I don't have a link anymore but just search for 'Pro Taper CR Highs'!

[@GrassoGrossoOgreLardoso]

Hi I am Frank

[@mrbrapz]

Hi Frank

[@Robocoppat]

Ok here comes the $64,000 question: How much of a difference did they make on the naked bike?

[@mrbrapz]

I think TarzanMotoVlogs done a review on them but they make such a difference. It took a little while to get used to but I wouldn't go back now! 😀

[@JoeWalling-mt07]

What bars are these bro ! I need them on my mt07

[@mrbrapz]

Pro Taper CR Highs!

[@christophelamotte1253]

Was your stock throttle grip glued already? how was it removed?

[@mrbrapz]

I honestly can't remember, sorry pal

[@tonykivanc]

Thinking of getting a protaper carmichael bend for my mt-07, which ones are yours?? and thanks for the video its really helpful

[@mrbrapz]

I can't believe I forgot to include which bars they are! I've put a link in the description! 😀

[@tonykivanc]

I am new to the motorcycle hobby but is this the carmichael bend or not? Cause that one also says its the protaper SE. thanks for the link!

[@mrbrapz]

@@tonykivanc mine are the CR Highs 😁

[@tonykivanc]

@@mrbrapz thnx bro, it looks dope af

[@extern9899]

make a pov video with these

[@mrbrapz]

100% ill get it done! 😀

[@oooooooliver]

what exact protaper bar is this? Henry/Reed?

[@mrbrapz]

They're CR Highs

[@richiep102]

Are these the high or low i went on the link you put on and theres a few options Cheers

[@mrbrapz]

CR highs 🤙🏻

[@danielgmusic98]

Bro how difficult was it getting off the handle bar from the center 4 hex bolts? I swear I feel like I’m about to snap off the thread getting them off?

[@mrbrapz]

Are you rotating the right way lol, I don't remember them being that difficult tbh

[@danielgmusic98]

@@mrbrapz yeah lefty loosy, I believe it because of the silly Allen key Swiss army style tool I’m using

[@crazyshaq1995]

@@danielgmusic98 bit late, but easier if you use a proper hex tool. Like a ratchet, more leverage

[@tomstc]

Nice video, does the brace not serve the purpose?

[@mrbrapz]

Not really no, would look cool with it on but the screen is in the way lol

[@anonymous_gamer_1992]

"start drilling that hole" 8:38 and " as long as its deep enough to fit the actual knobbly bit in the hole" 9:05 had me creased

[@anonymous_gamer_1992]

and "stickin hard on the inside"10:11

[@mrbrapz]

😂😂😂

[@nathanhammacott3]

Do you have a link for these bars??

[@mrbrapz]

Here you go, mine are CR highs - www.dirtbikexpress.co.uk/product/pro_taper_se_seven_eighths_handlebar_-_black

[@nathanhammacott3]

@@mrbrapz king. Thank you

[@D1sc1p1e]

Is your year an ABS model? Mine's an ABS 2018 and my cables were too short for the cr highs 😢

[@mrbrapz]

Yeah it is bro, I don't think I had a problem with it to be honest, what did you end up doing to get around it?

[@richiep102]

Did you get round it ?

[@D1sc1p1e]

@@richiep102 hi yes, sorry for the late reply guys! I ended up going in and rerouting the cables which worked. Was able to install klx 110s plus 1" pullback risers.

[@jakespeed9419]

"Abrasive stuff" knurling bro, knurling....

[@antonioradobuljac8249]

Its cr high or cr low?

[@mrbrapz]

CR Highs my guy! 😀

[@jakespeed9419]

Cut the "knobbly bit" off

[@keshsthanakiya5789]

😍

[@mrbrapz]

😀

[@alessmuk6164]

It is just for model after 2017 this doesn't make sense for model 2014-2017, it doesn't go together, if you have Abs, the cables are too short, there are no variants, I bought one, I can just throw it away!!!!!

[@mrbrapz]

I've managed to fit these bars onto both gen 1 and gen 2 Mt07's but I have heard people having the same issue!

[@therealbabydriver6674]

L Grips no diddy

[@clintgrimmett1238]

Knobbily bit😂

[@mrbrapz]

😂😂😂

[@Shay_K05]

Bruv how old r u through the mask u look in your 20s but your voice says older and u dress in Nike and adidas I just can’t figure it out😂

[@mrbrapz]

Mentally i'm about 50 but physically i'm 24 haha 😉