I just replaced the factory VDO vacuum, and volt gauges on my motorhome yesterday. Luckily my trans temp gauge still works perfectly. Let's go Brandon 1st comment too 😆
@sly23922 жыл бұрын
nate. you seem very maticules in all the tasks that you take on, and you have a good imagination and eye for things. keep up the good work, and i always enjoy your videos.
@F2391412 жыл бұрын
Oh yeah my VDO gauge reads 210 ish on my 1987 454, going off the temp port in the head between 2 cylinders on the right bank. I'm toying with going to full port vacuum on the advance on the distributor to see if I can get the idle temp lower. I'm running a 165 Edelbrock high flow thermostat. Wish there was a way to private message you I could go into it real deeply with you on all of your issues, I'm constantly tinkering with mine out of boredom. I also have every GM factory service manual, even the rare ones.
@F2391412 жыл бұрын
I switched to manifold vacuum and not ported today, now idle temp is about 170
@scotthouchins14082 жыл бұрын
Always making your home better...very nice. What you need now is a big egg salad sandwich on toast👍🇺🇸🥃
@Sparky-joystick.13082 жыл бұрын
Really good clean job you did
@jerryjerry86732 жыл бұрын
My go-to adhesive remover is WD-40. It softens the glue and encapsulates it with oil so it doesn't re-stick. Its a much better cleaner than a lubricant in my opinion.
@backwoodsbungalow96742 жыл бұрын
Agreed, I prefer 3 in One machine oil and penetrating oil for lubrication rather than WD40 which was designed as for Water Displacement.
@johnstuart85112 жыл бұрын
Just remember to top up your fluids. All Good. Stay safe. Stay Cool. Regards
@calvingeisinger26392 жыл бұрын
Lighter fluid will take that adhesive right off. It’s good for removing a lot of gunky stuff without damaging a delicate surface. Works on plastic too, without harming it. I get it cheap at TSC.
@markhenderson34982 жыл бұрын
The new coolant sensor is mounted right on the top of the thermostat and might be reading higher there. Also…with it mounted up that high it might be in an air pocket? Just a thought.
@ronethridge98752 жыл бұрын
good to have backup gauges/a good job/thanks much
@AQUATICSLIVE2 жыл бұрын
Nice man. If you want some lenses made for those lights hit me up I can print some up on my 3D printer. They turn out pretty decent. Just have to tell me the measurements.
@rebelyell15802 жыл бұрын
Pretty cool gesture from you Aqua!
@40belowful2 жыл бұрын
Nice :)
@F2391412 жыл бұрын
Hey Nate, I figured out alot about the temp readings on different ports and how to run the vacuum advance on the distributor. If you want some help reply and I'll post up my email long enough for you to get it.
@jimshomecomforts85052 жыл бұрын
Do you get better fuel mileage with the electric fans? Also does this keep the engine cooler in stop and go traffic?
@Sparky-joystick.13082 жыл бұрын
In wisconsin get cold
@cordcd72 жыл бұрын
I see your HAM handbook there, are you still studying for your test? It's on my list of to do so I should just do it. Happy Thanksgiving!
@ClassALiving2 жыл бұрын
Yup, about half way through, it's not too hard to learn imo. Happy Thanksgiving!
@cordcd72 жыл бұрын
@@ClassALiving awesome! I’m gonna get on it!
@tgearing32172 жыл бұрын
Howcome you don't like your thumbnails?
@edneialmeida76122 жыл бұрын
Boa noite muito top serviço amigo
@valmirramos41952 жыл бұрын
Ficou muito bom!
@Richard_Biggs Жыл бұрын
Check out the mechanical temp Guages. Might be more accurate
@vemtrak12 жыл бұрын
Quickest way to remove those annoying stickers is carb cleaner.
@alanwarner6842 жыл бұрын
Use an IR heat gun on the block to check water temperature!
@offgridwoodworld2 жыл бұрын
With them temp sensors you must be getting ready for some big trip,, don't forget to paint "Let's go Brandon" on the back of your rig
@nomad1ne2 жыл бұрын
Hate those PLASTIC SHRINK WRAP packages
@jimmyking-gaming84532 жыл бұрын
its stupid how they put those stickers on those fittings
@jimmyking-gaming84532 жыл бұрын
also first
@stevensemke85392 жыл бұрын
Most vehicles with electric fans fans don't turn on until 212 degrees
@tgearing32172 жыл бұрын
Break one and save one or what?
@ianhargreaves49782 жыл бұрын
Is this a video of how to remove stickers
@Chudsaves6 ай бұрын
Sorry that don’t work. It HAS to be mounted in the pan for accurate temp.