£0.03 per kWh heater modification - Top facts & lies on diesel heaters - waste veg oil burn success

  Рет қаралды 1,514,023

Joshua De Lisle

Joshua De Lisle

Күн бұрын

Пікірлер: 2 900
@joshuadelisle
@joshuadelisle 27 күн бұрын
I Hope this was useful, I've done 3 videos so far on the heater and i've got another to come where I make a water cooler and underfloor heating. Heres some links: The Diesel heater I recomend getting: UK: amzn.to/3ZO5S57 USA: amzn.to/3ZQgBMr Diesel heater featured: UK: amzn.to/3TUGYgo USA: amzn.to/3TUGYgo Additional affiliate links: Power supply 240v - 12v 300w UK: amzn.to/3BhmvZO USA: amzn.to/3PaYJoc glow plug burner mesh: UK: amzn.to/4euSkQv USA: amzn.to/4erp1OH Cheers J
@paullomas8769
@paullomas8769 5 күн бұрын
Hi, just a thought if you tip the water out of the bucket and replace it with sand you should have then created a heat battery that will stay warm for ages and it wont leak into your exhaust😊
@blief8850
@blief8850 Жыл бұрын
The water in your exhaust is probably not from a leak in the line, but from condensing water of the exhaust fumes. Burning hydrocarbons creates CO2 and H20. Cooling the exhaust in the bucket condenses the water vapours from the exhaust.
@Baddad36
@Baddad36 Жыл бұрын
That is exactly what it is.
@Electronics-Rocks
@Electronics-Rocks Жыл бұрын
Yes I made it a point to have my exhaust downhill. Also the condensate is acidic and a reason why exhausts on your car rusts
@Electronics-Rocks
@Electronics-Rocks Жыл бұрын
I am using a household radiator with the output at the bottom to take the condensate out which can be surprising.
@joshuadelisle
@joshuadelisle Жыл бұрын
Very good point. Cheers J
@MartialArtUK
@MartialArtUK Жыл бұрын
Put a condensate trap and pipe from an oil boiler on it 👍
@citizenkane2349
@citizenkane2349 11 ай бұрын
What surprises me the most about this video is how many laws/regulations the UK government can implement to make citizens' lives harder.
@Henry-gj7mr
@Henry-gj7mr 11 ай бұрын
It shouldn't be a surprise. The Gov. is full of users and abusers.
@wylinout2257
@wylinout2257 11 ай бұрын
Rulers of people can do that
@ramblingman8992
@ramblingman8992 11 ай бұрын
Dilute waste engine oil with 5% petrol and it becomes black diesel. This can be used in your heater.
@cicero2
@cicero2 11 ай бұрын
Our corrupt leaders are run by the big power companies and big pharma, so making things difficult for Joe Citizen is no surprise.
@matthewyabsley
@matthewyabsley 11 ай бұрын
Or how many laws and regulations protect me from you. ;-)
@petercordingley927
@petercordingley927 11 ай бұрын
Just a suggestion if you used a metal tool box or old ammunition metal box, dip the exhaust pipe in then fill with kiln dried sand you will create a heat sand bank which will retain all the exhaust heat up to temperatures in excess over 1200 centigrade far higher than water.
@kevinfox3875
@kevinfox3875 Жыл бұрын
PS The viscosity of Diesel is 35 Redwood, Kerosene is 28, but the waste oil is likely to be c. 200 or so. If you added a tiny 5W 12v bulb to preheat the waste oil thereby lowering its viscosity, you most likely would eliminate the unburnt fuel (smoke) withiut having to add the Kerosene to your waste oil. Keep up the good work
@bradleysr
@bradleysr Жыл бұрын
Why not preheat it with exhaust heat?
@dannywilliams6643
@dannywilliams6643 Жыл бұрын
​@@bradleysrbrilliant
@simonmasters3295
@simonmasters3295 Жыл бұрын
​@@dannywilliams6643think about how it would start
@dougle03
@dougle03 Жыл бұрын
@@simonmasters3295 Smokey to start, then it'd clean right up.
@supersportimpalass
@supersportimpalass Жыл бұрын
@@dougle03most guys that burn waste oil in their diesel trucks switch back to regular diesel before shutting the engine off. This makes cold starts much easier.
@brianblack138
@brianblack138 Жыл бұрын
I love it. In the early 2000s I was running my truck (a Chevy 6.5L turbo diesel) on waste vegetable oil. I realized I spent so much time devising more efficient ways to collect and burn it that I probably wasn’t saving much money.
@kd2239
@kd2239 Жыл бұрын
4:20 Just to note, energy is not charged per kW (kilowatt), but per kWh (kilowatt hour). It can get confusing when the wrong units are used. Thanks. Great video.
@benjurqunov
@benjurqunov Жыл бұрын
Agreed !! Too many people don't know or care to use correct basic engineering expressions. Sadly it puts anything else in their program in question of accuracy.
@pyramidsinegypt
@pyramidsinegypt Жыл бұрын
@@benjurqunov So if you happen to misspell a word in an email I'm to question the correctness of everything else you wrote? If you ever misspeak I'm to ignore everything else you said? (not to mention that a) it's not an 'engineering expression' and b) only electricity is charged per kilowatt hour and from all else in this video you can still make your own calculations).
@mcg6762
@mcg6762 Жыл бұрын
@@pyramidsinegypt It's not about typos. It's about using the wrong units in a very confusing way which leads to misunderstandings. Energy and power are not the same thing. I agree that if someone is doing experiments and using the wrong units when talking about it we should question if that person knows what he/she is doing.
@fredflintstone1428
@fredflintstone1428 Жыл бұрын
@@mcg6762 What was it specifically that he got wrong? If something consumes 1kW of electricity (runs at 4A @250V), and it is runs for an hour, doesn't it consume 1kWh of electricity?
@mcg6762
@mcg6762 Жыл бұрын
@@fredflintstone1428He was saying and displaying kW instead of kWh in several places in the video.
@aarondavis8433
@aarondavis8433 Жыл бұрын
you should run the exhaust tubing through a bucket of sand. the sand will heat up preventing exhaust condensation as well as trapping more heat for longer radiant heat exchange.
@ghostwhite1648
@ghostwhite1648 Жыл бұрын
throw a bottle of water in that sand, take a pipe angled downward into a cold sand with another bottle to distill water at the same time
@michellelaclair
@michellelaclair 6 ай бұрын
is that similar to a rocket mass heater design / idea?
@Shade_Tree_Mechanic
@Shade_Tree_Mechanic 16 күн бұрын
​@@ghostwhite1648Using the otherwise wasted heat to distill water is an excellent idea
@jamesajanda
@jamesajanda 9 ай бұрын
I love the content on this channel!!!! I bought one of these heaters a few years ago and still haven't unboxed it. Believe it or not... I was a Captain in the U.S. Army back in the mid 2000's and I was burning used vegetable oil in my 2500 Dodge Diesel truck!! I would gather the used veg oil from the dining facilities on post and take it home and strain it through a window screen into a 30 gallon trash can. Then I had two pumps that would pull the oil from the bottom of the trash can at the petcock. The pumps would run the oil through two different size micron filters two get the particulate down to 5 micron. Then straight into the fuel tank on the truck. Before the oil leaving the trash can I had to include 10% gasoline, 1 qt of diesel clean, and about an once of a special additive that I bought from a dealer here on youtube. It worked pretty well but you had to leave 1/3 tank of diesel in the truck or you would clog up your fuel filters on the engine. Anyway, it worked until diesel prices dropped after Hurricane Katrina. What I found interesting was that during this time Diesel prices were near $5.00 a gallon but I would fill up on Kerosene at the pump, when I could find it, for about $1.67 a gallon. Kerosene is actually what is considered #1 diesel, a cleaner version of diesel.
@JamesEarl-e9d
@JamesEarl-e9d 7 ай бұрын
Why did you put the C0 detector on the floor around 21mins then start talking about smells 😂
@Dave5843-d9m
@Dave5843-d9m 21 күн бұрын
Used cooking oil is easy to clean. You need an inverted barrel with the bottom cut off. Fit a water heating element in the (new) bottom side so it runs parallel to the bottom of the barrel. Fit a petcock into the bottom to drain the water. The screw cap will allow crud to be washed out. Fit another petcock 25% up from the bottom. Fill the barrel with water to below the upper petcock and top up with used cooking oil. Now heat the water and boil it for an hour. The steam will literally wash the oil. You can drain the (now clean) oil via the side petcock. Drain the dirty water via the bottom petcock and barrel bung. The small amount of trapped oils stays in the barrel and gets added to the next boil wash. A commercial kitchen water boiler will do the same job for smaller batches.
@bryancondrey6457
@bryancondrey6457 Жыл бұрын
Idea: your waste heat exhaust could be modified by using a partially water filled rain gutter deep enough to encompass the exhaust tube but the tube needs to run downhill to allow any condensation accumulating a place to drain and run outside. In the US, that usually means 0.25 inches per foot drop. Next idea: use copper water pipe so you can braze or solder the fittings for a leak free path. The inside of the copper is smooth so accumulating dirty condensation is minimal and it leaves quickly. The biggest downside I see is keeping the water filled gutter from freezing if your climate gets that cool.
@GoingtoHecq
@GoingtoHecq 9 ай бұрын
It would take expensive silver solder to be safe from being melted by the exhaust. If he just uses one large coil it would take very few solder joints.
@eyeorewolf
@eyeorewolf Жыл бұрын
I like the way you used the exhaust run inside to maximize efficiency. I will probably do the same but put a slight downward slope on the exhaust pipe to allow any condensate to run out. I may even duct a small 12V fan behind the pipe to get a bit of a forced air effect off the exhaust pipe. I plan to use a battery with solar to run the system regardless how cheap using a power supply appears to be, I like the idea of the system being 100% off grid in the event of a power failure. I have a lot to do in preparation for my 9M x 12M pole barn before this system would provide any real benefit. Insulation is my first step and I will probably require two for these units on opposing walls. Thank you for taking the time to make this video. Very informative.
@PINKFL0YD-s2h
@PINKFL0YD-s2h Жыл бұрын
Why they don't want us to have cheaper heating is immoral especially when people like me have not had any heating this winter, when British gas made record profits
@chrisgibson2328
@chrisgibson2328 Жыл бұрын
It's nothing to do with climate control but is about control. It is about making things more uncomfortable/expensive. Its about creating fear and despair. They are evil and greedy.
@neil2945
@neil2945 Жыл бұрын
I live in Michigan Here in the State it's the same thing and it all comes down to one word "control" and my heart goes out to you and yours that you make it through the winter
@joshuadelisle
@joshuadelisle Жыл бұрын
I nearly ranted about that. Had to hold back. Cheers J
@PINKFL0YD-s2h
@PINKFL0YD-s2h Жыл бұрын
@@chrisgibson2328 agreed making money
@Sub-Kuch13.13
@Sub-Kuch13.13 Жыл бұрын
GREED CRISIS not a living crisis. Governments that should be protecting the public, but looking the other way, to suit their employers. The energy companies & Banks.
@ollypolly18
@ollypolly18 Жыл бұрын
brilliant. i firstly did this to my boat about 4 years ago. not so good in choppy sea but still worked good. when the gas price went up i did the same sort of set up as you. I have one blowing upstairs and one down and it actually keeps my old 200 year stone hose around 20c and so very cheap to run. i did get a free 55 gallon drum of paraffin that im using and expecting to last a few years. with two multi fuel burners two diesel heaters solar panels that iv set up myself running a 3kw grid tie inverter and my esta breeze i1500 turbine i pay not a lot to the utility ripoff gangsters. iv not worked out the cost but its not a lot
@mmac4047
@mmac4047 Жыл бұрын
Great job, I taught bio-diesel at the local college, and drove coast to coast across the United States, Labor Day weekend (5 Days) in 2002 in A 2002 VW Beetle with 600 Miles at the start making 3036 miles west to east astoria oregon to Ocean city MD and of course back. I did similar experimenting and refining. Using a SS mesh filter, then two diesel filters I would ultra filter the waste oil from a chip (potato - thin slice). The last filter in the chain was a water block because I would store it and the oil is hydroscopic so when it cools down ( like when the temperature in the room cools at night) it actually draws moisture out of the air (oregon Pacific Northwest) it would settle on the bottom. I still have the car more than 240,000 Miles still run biodiesel ( available at the pump called B15) I have two other Vw’s with diesel engines 2006, 2014 and a gmc 6.5 Lt Turbo diesel 4x4 truck. Your doing it nearly exactly the same and never had any problems and change my car/truck fuel filters per mfg schedule, I would open the filter car fuel filters never found anything big or a lot ( no rust no contaminates) I had a lot of people tell me all kinds of things but never had any issues. When freezing temps expected just increased the diesel ratio to 50/50 then when it warmed back I would go. I maintain all the vehicles still on original glow plugs and injectors and high pressure pumps. But its likely how I drive, i am on the original clutch and the brake pads on the front were changed just because they were 18 years old, there was still more than half the available wear left. Enjoy the adventure. Mike
@jrperrotta
@jrperrotta Жыл бұрын
Pay attention to the exhaust pipe outlet and install the 'H' design vent cap that creates near zero back draft pressure as wind can create exhaust back pressure into the burner. The outside wind pressure can easily defeat the pressurized exhaust
@juiceofsapho
@juiceofsapho 10 ай бұрын
Please use the appropriate unit for electrical energy, it is kWh (1kWh = 1kW * 1h) "kilowatt-hour" . The kW is the unit for power (potential to do work over time) so that multiplied with time gives energy or work. Base unit for energy is joule (1joule = 1W * 1sec) which is 1/3600000 kWh, so it is a very small amount of energy 😊 Very interesting subject btw!
@torbjrnjohansen-skavdal7802
@torbjrnjohansen-skavdal7802 10 ай бұрын
No need to add pedantry, as he's talking about both electrical energy, thermal energy and potential energy. Also, this isn't Physics class, but more of a Public Service Announcement to help you loosen the gov't grip around your wallet...
@flexairz
@flexairz 10 ай бұрын
@@torbjrnjohansen-skavdal7802 Nope. If you explain something you should use the correct terms so we are all on the same page.
@mothMagnets
@mothMagnets 10 ай бұрын
@@flexairz Yeah, it hurt my head every time he said kilowatt
@lloydevans2900
@lloydevans2900 Жыл бұрын
I had the same problem running mine on vegetable oil - I was using fresh sunflower oil rather than waste oil, and the exhaust was spitting out unburned fuel and a lot of smoke. It also stopped working after a few days, since there was so much soot deposits in the exhaust pipe that it partially blocked up. I solved the problem by mixing the vegetable oil about 50:50 with white spirit (I had a cheap supply of that), which thins it out nicely. When it comes to filtering your waste vegetable oil, I would recommend doing it in stages: Pass it through a wire mesh first (an old kitchen sieve would do the trick), which would take out any large-ish chunks of old batter or chip fragments. Then through a finer mesh, such as "OOO" grade steel wool. Finally through a paper or fabric filter, either coffee filters or a couple of layers of old tea towel. The first two stages should be fairly quick, and the bits they take out should mean the final stage doesn't clog up so much, so that should be quicker too. Another filtering tip: If you are going to mix your waste vegetable oil with some kerosene or diesel (or white spirit) anyway, you might as well mix this in before filtering it. This does mean a greater volume going through the filter of course, but the lower viscosity should speed up the filtering, so on balance it could well be faster overall.
@keithandrew3079
@keithandrew3079 Жыл бұрын
Great advice cheers
@godzillas6301
@godzillas6301 Жыл бұрын
Great advice . For filtering i used a fine sieve . No idea what its original intention was to be but it did the job for me without issue . I then would simply double up kitchen roll in a funnel and have a tap on the 25 litre tub filled with oil to regulate flow . Top tub drips into the funnel which has another tub bellow it to play catch ..... get it to drip and ignore for a day or 2 . I will fess i never though of thinning it out with paraffin diesel or white spirit .... ill remember that for next time .
@steverpcb
@steverpcb Жыл бұрын
Use rape seed oil instead as it can be added to the fuel of pre common rail diesel engines upto 40% with no issues.
@lloydevans2900
@lloydevans2900 Жыл бұрын
@@steverpcbThat might be ok for a diesel engine because they inject the fuel into pre-heated compressed air, burning the metered spray of fuel all in one go. Diesel air heaters burn fuel with a continuous flame in air at ambient pressure, so are quite different. Both the viscosity and boiling point have to be low enough for the fuel spray to adequately vaporise, in order for complete combustion. Otherwise you get a lot of soot production which blocks up the exhaust outlet, and in the worst case you get ignition failure and unburned fuel spraying out of the exhaust. Also, the issue with diesel cars and vegetable oils isn't so much the engine itself - the first diesel engines to be designed actually burned peanut oil, and were only later on used with petroleum oils. The vegetable oil causes problems for the rubber gaskets in the fuel system, causing them to swell or even disintegrate. If you go through the fuel lines and injectors, replacing any rubber gaskets with viton (perfluoroelastomer) gaskets, it should be able to burn neat vegetable oil of any type without any problems at all.
@steverpcb
@steverpcb Жыл бұрын
@@lloydevans2900 Sunflower oil is known to coke up diesel engines badly as do many other oils. Another issue with veg oils is that some set solid and need warming to be able to pump them.
@stalbertjocelyn
@stalbertjocelyn Жыл бұрын
Make sure your pump is on a 30deg angle to get rid of air bubbles or you will kill it. The air will accumulate and the plunger will wear the inner wall.
@penmanworthington6595
@penmanworthington6595 Жыл бұрын
Great video, I have repaired many of these heaters in trucks. Although very reliable, the main faults is the internal fan failing and if white smoke or difficulty in starting, that green gasket between the heat exchanger and fan hardens and cracks with age probably depending on the amount of start ups the heater experiences.
@davidconner-shover51
@davidconner-shover51 Жыл бұрын
or, more nastily, hard shutdowns. Bearing failure did my last one.
@s1dew1nd3r4
@s1dew1nd3r4 11 ай бұрын
do they just run of 12v? could you run them off a leisure battery or two or would it just zap them quick time?
@zebraforceone
@zebraforceone 11 ай бұрын
​@@s1dew1nd3r4 Yup they will run off 12V or 24V. There is a ~10A draw on startup for about a minute, which is mostly the glow plug heating up and the fan spinning at full. Same when it goes through it's shutdown routine. On the lowest setting it will use about 1A / hour. You can easily run one off a 110Ah battery, smaller batteries can struggle a bit with the startup and shutdown draw. A 110Ah lead acid leisure battery will give you a good 50 hours of running a diesel heater before it's flat, provided you don't keep turning it on and off again repeatedly. You could run that off a pretty modest solar setup. Source: I'm sat in my camper with my cheap chinese heater, it's -2 outside, I'm sitting here in my pyjamas feeling toasty :)
@thetruthfrmtyme2tyme
@thetruthfrmtyme2tyme 11 ай бұрын
I like the heater I could run it off solar and black diesel and I really like the micro turbo. Why do we not have these in the US ? Or do we all ready without the turbo witch would be fuel oil heaters but there not as efficient
@thetruthfrmtyme2tyme
@thetruthfrmtyme2tyme 11 ай бұрын
Where can I buy it
@DavidMamanakis
@DavidMamanakis Жыл бұрын
I appreciate your diligence in your testing of these units... We tried one of them with actual automotive waste oil. I don't recommend it. It almost ruined one of our units. We even tried cutting it with red diesel (which we can still use, over here)... I haven't tried waste cooking oil, it might be worth looking at. Caster oil is used, similar to kerosene, and might burn nicely, or could be cut with kerosene or diesel... I don't know the cost per liter, but it might save a little money. I have 4 of these units, 3 are currently working (the 4th is the one we tried with automotive waste oil)... I have one for when I'm out camping (a portable unit, similar to yours) and one installed in my shed. I had considered running a radiator-type system to trap more heat in the shed, but haven't actually built it yet. I was considering using copper tubing and a small fan. My heater runs off a battery and is supported by a 200w 24v solar panel. I plan to place a second solar panel to increase the amps for recharging my battery system (about 100ah SLA battery pack, made with used BackUPS batteries)... Thanks again for the video, I learned a few things!
@gerrys6265
@gerrys6265 Жыл бұрын
Thanks. Great Video and testing. I burn Waste Veggie in my car and boat engines after letting it settle for a few weeks. Then I filter it through 5 micron bag filters. These bag filters are about 10 dollars in Canada. They are about 17 mm in diameter and 600 mm long. The oil goest through them pretty quickly. I just do it by gravity and a barrel of oil takes about an hour. I wash them with soap and hot water after every couple barrels. If the oil is particularly dirty from the restaurant or has a lot of bits in it, I put a a 400 mesh filter 'bag' inside the 5 micron filter bag and wash that as necessary. Works great, but you do have to let the oil settle for a few weeks first or it will plug up the filter bags pretty quickly - depending on how heavily used the oil is from the restaurant.
@Fosgen
@Fosgen Жыл бұрын
Route exhaust through through big old steel tank, then fill with sand, and close it, you created heat battery. After cycle end, lets say 10 hours of haeting air, heat battery will be hot and should give infrared heat out for next hours, therefore your garage could still be much warmer inside than outside in the early morning, without using a single drop of fuel extra.
@chrisabraham8793
@chrisabraham8793 Жыл бұрын
Very good idea.
@SynKronos
@SynKronos Жыл бұрын
25mm gravel or greater through a perforated pipe perhaps but sand. Nope. You'll suffocate combustio, coking up the burn chamber and worse as the sand gets wet it will clog further.
@chrisabraham8793
@chrisabraham8793 Жыл бұрын
@@SynKronos I don't think the exhaust pipe was ment to vent into the sand but coiled in the bucket of sand and vented back out like the bucket of water. Just heats the sand.
@SynKronos
@SynKronos Жыл бұрын
@@chrisabraham8793 Ah, that makes sense. But it would have to come out of the bottom of the bucket or water would fill the exhaust
@chrisabraham8793
@chrisabraham8793 Жыл бұрын
@@SynKronos I suppose with a bit of fire clay at the bottom of the bucket surrounding the pipe would stop the sand falling out. I am quite surprised that the amount of heat generated by the exhaust hasn't evaporated the moisture right at the very end.
@charlesdonaldson962
@charlesdonaldson962 Жыл бұрын
Okay here's one. When you increase the length of the exhaust beyond the maximum that stated by the manufacturer after their testing, he would have to increase your inner diameter size by 1 to go a certain distance further or to go through more fittings elbows whatever. For water flow there calculators on everything every type of fitting etc I'm sure there is four exhaust as well and I'm also sure bever doesn't say what the maximum is for that thing or have much of installation instructions. Thanks for giving me something good to look at!
@jlr3636
@jlr3636 Жыл бұрын
“They don’t teach you nothing practical “ very true statement, mainly in today’s system. My first year in high school 1964 (USA) I took a class, divided into 4 sections, drafting or mechanical drawing, electronic where we did projects using surplus analog phone switches, sheet metal fabrication, and metal working. To this day it was probably the most impactful class I ever took.
@DinkyDoughnut
@DinkyDoughnut Жыл бұрын
I just took things apart out of Curiosity, even if I ruined part of their construction. However, my father forgave me as the item or appliance was already malfunctioning and I could always blame the age or general deterioration through use that was the failure. But I got better and better at it and now regarded a genius. So, Rock’n’RoLL is ere to Stay.!
@johnwilson6732
@johnwilson6732 Жыл бұрын
just a comment. They obviously were not successful teaching you about double negatives in you English classes. They don't (do not) nothing practical, should be they do not teach you anything practical... For the rest subject matter in class is only valuable to you if you are interested, otherwise as you say they were not practical. Others may have found them practical for their needs
@dutch2756
@dutch2756 8 ай бұрын
@@johnwilson6732 thank god practical things are more important as language.
@feaksy
@feaksy 6 ай бұрын
I also did metalwork, tech drawing, art and woodwork at high school in Australia in the 70s and became a carpenter. They also taught me to think for myself and use critical thinking, Not like the indoctrinated kids these days.
@wizardwillbonner
@wizardwillbonner 10 ай бұрын
As a kid growing up in the 50s I can remember my stepdad telling us about having an extra tank on their car filled with old motor oil/diesel mix, with a line wrapped around the exhaust to a valve on the fuel line. They'd start as normal and after running for a while, would switch over to the mix and turn off the ignition. Just before their destination turn ignition on and mix off, thus allowing them to shut down normally. He said his car was an old jalopy, so I'm assuming it was a model "A"!
@diepurpledino
@diepurpledino Жыл бұрын
Here's a thought - for particulate emission detection, use a green laser pointer. Does a great job of illuminating otherwise invisible particles. Tried it during California wildfires a couple years ago - it was like having a mile-long lightsaber.
@joshuadelisle
@joshuadelisle Жыл бұрын
Good idea. Thank you. Cheers J
@jd01665
@jd01665 11 ай бұрын
@@joshuadelisle There are meters that measure the AQI. The combine all the particulates and also things like HCHO, TVOCs, etc. Burning anything is going to affect air quality. So probably need an air purifier unless you prefer using your lungs to filter the stuff produced by the combustion.
@joshuadelisle
@joshuadelisle 11 ай бұрын
@@jd01665 I've got one. Video coming shortly. AQI reads excellent from 1m away. Cheers J
@TheBlackmunch
@TheBlackmunch Жыл бұрын
That is the second most informative video I have ever seen on practical heating, both of them yours. Extremely well done, and presented. Thank you for all of the information 👍🏼
@joshuadelisle
@joshuadelisle Жыл бұрын
Thank you so much, I'm really glad it helps. Cheers J
@tomad4051
@tomad4051 Жыл бұрын
YES, to EVERYTHING SAID, What? I am shouting? Damn Straight, I AM !!! ❤❤❤❤❤❤👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻🔥🔥🔥🔥🔥🔥💪🏼💪🏼💪🏼💪🏼💪🏼💪🏼
@joshuadelisle
@joshuadelisle Жыл бұрын
@@tomad4051 you're very kind. Cheers J
@ModernSurvivalists
@ModernSurvivalists Жыл бұрын
Excellent video!! Spent many years experimenting with WVO (Waste Vegetable Oil) for fueling diesel engines. I see a lot of parallels with this. For a diesel engine we achieved clean and efficient combustion by preheating the input oil to about 160F (71C). At this temperature the WVO thins out to a viscosity very close to diesel and atomizes much better. We did this by using waste heat from the engine with a fluid-to-fluid heat exchanger - engine coolant one side and WVO input line on the other. We also used a startup and shut down phase on regular fuel just like you already are and would only switchover to WVO once the engine was warmed up with the 160F preheat temp reached. You don't have engine coolant to use for preheat in your case, but you do have the exhaust heat. We experimented with that and found it to be too harsh / hot to use directly in a heat exchanger with the oil - it would polymerize and plug up after a while. But since you plan to already make a hot water heater with the exhaust, you could very easily use your hot water output as an input to preheat your oil input to the burner! This video is re-sparking my interest and I may have to add some similar experiments to my channel!
@uploadsnstuff8902
@uploadsnstuff8902 Жыл бұрын
So would it'd be possible to use a little water pump in a close circuit that runs around the exhaust and into the fuel tank to heat it a bit? It should be linked to a temp sensor that somehow shuts the line on and off depending on the temperature of the fuel and the water so it doesn't boil obviously.
@ModernSurvivalists
@ModernSurvivalists Жыл бұрын
@@uploadsnstuff8902 Yes I think that would work. I'd definitely include a high pressure relief value incase of steam buildup - just like the old boiler systems used. A pump may not even be necessary as it might be possible to thermo syphon a loop like a drip coffee machine.
@nirodper
@nirodper Жыл бұрын
The heated air (not the exhaust) would work great as it's a much lower temperature, just wrap a small copper tube coil and put it inside the ducting
@GRAYBELL27
@GRAYBELL27 Жыл бұрын
I can't see the point of having a thin, solid skin hose on the input to the pump. It's necessary on the output to prevent loss of pressure due to the flexing of a conventional tube, but using solid wall hoses on the input along with a great big filter (most likely with air still in it) involves all those extra connections for no benefit as I can see. Use a bigger hose and save yourself some well deserved time and penny's 😅
@agentwhitedog1
@agentwhitedog1 Жыл бұрын
Joshua: Units of energy are measured in kilowatt-hours, not kilowatts. A kilowatt is a measure of power.
@leealangrothe5552
@leealangrothe5552 Жыл бұрын
Great Tenacity
@03056932
@03056932 Жыл бұрын
We all know what he meant. Why is his comments full of people flexing for their own gratification? Not enough interest in our hobbies from family members?
@arjanl.2168
@arjanl.2168 Жыл бұрын
Units of energy are measured in (Kilo)watts, not (Kilo)watt-hours. (Kilo)watt-hours is the sum of total (Kilo)watts, used in one hour. So Yosh (and almost the entire world) is right by mentioning capacity in Kilowatts.
@Conservator.
@Conservator. Жыл бұрын
@@arjanl.2168you are mixing up power and (the amount of) energy. Energy is measured in Joule or calories, Nm or kWh Lookup the Wikipedia page for units of energy and check for yourself.
@TheComputec
@TheComputec 10 ай бұрын
@agentwhitedog1 Close.. but wrong... Kilowatts is the energy it uses/provides. Kilowatt hours is a method for calculating its power consumption over time that can be expressed as a cost
@maccacoffee
@maccacoffee Жыл бұрын
Hi Josh. I think you should put a right angle mounting bracket on your fuel change over valve so that the drain retainer plug on the bottom of the unit can be orientated correctly,,,,,,,, it does act as a sedimentor/separator and on lawn mowers or motor bikes when the cup at the bottom is removed you will find water or fine sediment in there especially if you are careless with your fuel quality ,DON'T ASK ME HOW i KNOW. as a qualified mechanic I have had lots of these off and rarely find no sediment or water, because of yours mounted on the side any sediment/water will go into one or the other of your fuel supply lines ( eg, diesel or kero. ) I appreciate you are more carefull. and I appreciate your channel keep up the good work. col.
@geoffthomas8528
@geoffthomas8528 9 ай бұрын
Really informative video. I bought an 8kw and installed it in my bungalow in Spain. However I decided to recycle the hot air output back into the air intake. The effects were impressive, as it halved the time it took to heat the bungalow. In addition, the heaters remote temp sensor reduced the heaters pump speed as the room got warmer. The heater was mounted outside.
@marcvpraet
@marcvpraet 2 ай бұрын
Hi Geoff. Living in Spain myself I’m very much interested in your experience with this heater for your bungalow. I like your idea of rerouting the hot air output back into the air intake but not certain if you Jean the hit air output (in full or in part) or the exhaust line. Can you please explain? We live in a bungalow which I insulated very well but our heating is still with inverters running partially on EV panels, partially on the grid (Iberdrola). I would like to use this air to air heating for the days / hours without sunshine… so in winter and at night. Can you indicate the efficiency of the heater in your bungalow and if possible, can we get in touch? We live on the Costa Blanca. Thanks. Marc
@stephenbaker3680
@stephenbaker3680 20 күн бұрын
Who is controlling the sentance word placement location in the posts? Its getting worse! Why is this running rampant the last few years?
@sgardner
@sgardner Жыл бұрын
You could always use your exhaust to heat a sand battery. Thank you for your excellent videos.
@Leo99929
@Leo99929 Жыл бұрын
Ideally, your exhaust would be roughly the same temperature as the air temperature in space you're heating. You could put a pipe around your exhaust and blow room air through the gap created in the direction against the flow of the exhaust. Counterflow heat exchangers can achieve the optimum of ambient temperature exhaust temperature.
@leonardmason6916
@leonardmason6916 Жыл бұрын
I have done this, put a 5" pipe around the extended exhaust pipe. To toggle on when the pipe is hot and brings in 80 degree outside air in 30 degree outside temps to create a positive pressure in the room with makeup air. I also use free alternative fuel.
@sirfenderjazzmaster
@sirfenderjazzmaster Жыл бұрын
I was thinking the same thing. 12v fan blowing through ductwork in opposite direction from exhaust. You could also consider installing 2x90s and doubling the exhaust back on itself. Would have kept all of the holes in your wall closer together if that is a consideration to someone.
@arti252
@arti252 Жыл бұрын
Is there a limit to the air intake temperature to the burner if not the air intake could suck air which is ducted over the exhaust pipe, no need to force it by a fan.
@johnTurner-ht1vm
@johnTurner-ht1vm Жыл бұрын
​@@sirfenderjazzmaster 0
@paradiselost9946
@paradiselost9946 Жыл бұрын
i go one better. 28mm copper pipe. cross drilled with bits of 3/16 soldered in. two reducers to wrap it in 50mm pipe. about a foot long. yes, i happily work in both units at the same time. thermosiphon heater, up to a hot water tank. solar panel thrown on the element for a bit more pizazz. some days i dont bother lighting up. old auto radiator inside the container.
@nelisjan4054
@nelisjan4054 Жыл бұрын
You should consider the drainage gradient of your exhaust since the exhaust is now coming from the bottom. might even want to consider a syphon to drain the condense water if you're increasing it's length or making it into a exchanger. Further a great informative vid!
@kenknutson1598
@kenknutson1598 Жыл бұрын
Burning one gallon of gasoline creates CO2 and 1.5 gallons of water. Ask a chemistry teacher why.
@vaalrus
@vaalrus Жыл бұрын
Indeed. I heat my large workshop with a condensing exhaust gas boiler, and the exhaust wraps around the heat exhanger, that has a sealed drip tube off the bottom, where it feeds into a siphon/trap that delivers waste water where it can be disposed of. And it’s a significant amount. :)
@equalizingforce2581
@equalizingforce2581 Жыл бұрын
I was going to get one of these for emergency home use. I was going to get an extension and run it up the chimney. Are you suggesting condensation would run back down the pipe making this impracticable?
@lookinin123
@lookinin123 11 ай бұрын
You've got to get rid of that corrosive condensation. Straight up is a recipe for disaster, IMO.
@silicon.alchemist
@silicon.alchemist Жыл бұрын
How about a coaxial heat exchanger? Run the exhaust tube inside a larger metal tube, which is used as the air intake (or at least part of it). This would mean that the incoming air is preheated which should improve efficiency. It could also be used to bring fresh air in from outside which would give the building a slight positive pressure.
@LUPIPUPI1
@LUPIPUPI1 Жыл бұрын
I think cold air provides a better mixture. When your engine is forced with hot air, it ends up burning more fuel to compensate for the lack of density. Cold air intakes provide an air-fuel mixture that is efficiently burned and used less fuel overall
@sierraecho884
@sierraecho884 Жыл бұрын
Is this true ? I don´t thing hotter air improves efficiency I think it is the other way around.
@shaggyrandy1264
@shaggyrandy1264 Жыл бұрын
Foundries like preheated intake air.
@sierraecho884
@sierraecho884 Жыл бұрын
Hot air in motor vehicles decreases the efficiency, because hot air is less dense so there is less oxygen per given volume.@@shaggyrandy1264
@dougle03
@dougle03 Жыл бұрын
@@LUPIPUPI1 I think he meant the internal air intake, not the combustion intake.
@johnwighton
@johnwighton 15 күн бұрын
Nice video and very useful. I just installed two heaters for my 4.5 x 4.5m double garage workshop. The exhaust goes straight outside now but having felt how much heat goes unused l with think of making a radiator. The instructions that come with the heaters were rubbish, so your tips on setting fuel/air mix etc has been great.
@stevee8698
@stevee8698 Жыл бұрын
I wanted to put one of these in my old caravan, but I wanted one that's not in a carry case. I was thinking of plumbing the exhaust downhill through copper pipe, through from the top of a large radiator, then out from the bottom so that water can't build up inside. Really enjoyed this video.
@petercroft9895
@petercroft9895 Жыл бұрын
The uncased versions are more common, and are intended for use in caravans and motorhomes. I put a 3kW one in a small bus conversion, it's an awesome piece of kit, 0C outside to 20C inside in about 15 minutes. Once it's up to temperature the fan slows right down and the pump becomes the noisiest thing.
@renaissanceman8564
@renaissanceman8564 Жыл бұрын
I see someone purposely building one to fit into a fireplace for homes built prior to 1980’s . I bought one for my Macgregor M and use in the shop . I ended up running an exhaust pipe through the wall then up a down pipe from my gutter to get the exhaust up to roof height of my house so not to suck it back into the garage or annoy my neighbors. My point is these are amazingly cheap to run so trying to extract every btu seems like rubbing two pennies together. Clean burning equals efficiency so if you try to burn shit it will plug up and not burn clean or just fail completely.Your exhaust pipe is the most important bit for keeping it clean burning and Avoiding CARBON MONOXIDE! These heaters come with a small silencer. It is not air/exhaust tight at all and does act as a condensation trap which is good but never inside where you are breathing the same air. So if you buy one of these you must have a carbon monoxide detector. I love mine but also got a small electrical heater that burns 50 to 70 amps @ 12 volts with a tiny fan to maintain a nice temperature after heating with the diesel . Ok cheers and prayers for peace on earth !
@ab_ab_c
@ab_ab_c Жыл бұрын
You did things almost exactly as I would have done them to arrive at your conclusion! Very well done! All you need to do now is put a sealed water cylinder around your exhaust tube to extract the rest of your exhausted heat, rather than allowing it to escape outside. Keep up the excellent work! Thanks for sharing!
@jimbo748
@jimbo748 10 ай бұрын
These have been used for cab heaters in lorry’s for decades, fitted one out of a lorry in a mate’s boat and worked really good
@HalfGodHalfBeast
@HalfGodHalfBeast Жыл бұрын
adding a couple of drops of acetone to each litre of used veg oil lowers the viscosity quite considerably - this will help with the filtering and the flow rate in the heater
@staintonguy
@staintonguy Жыл бұрын
I think you should not use paper element filters for diesel or kerosene unless specifically designed for it. Normally fine wire screens are used for diesel if you check at your auto parts dealer. The common cheap small paper element filters are for Petrol. Apparently the paper element eventually goes “soggy” in diesel and deteriorates. As it does so, it can pass along the fuel line and cause clogging/damage further on which can be difficult and expensive to fix in a Diesel engine.
@robinspratt6057
@robinspratt6057 11 ай бұрын
These heaters are so forgiving of their fuel. I have been running a 50:50 mix of waste veg oil and kerosene in mine for the last year. It starts and runs with no issues even in cold temperatures! Does away with the need for two tanks and the change over but as half of my fuel is free the running cost is halved! Yet to open the burner to decode it so I can’t comment on soot but the point is it’s running without any hiccups ☺️
@leifhietala8074
@leifhietala8074 11 ай бұрын
The long horizontal run of the exhaust is excellent! The draft blower generates sufficient mass flow to carry along any condensed water to the exit and spit it out the end, outside the building. For maximum efficiency, double or even triple it. You might need to install a larger diameter exhaust pipe to keep the static flow resistance from becoming too much. Another length or two of exhaust pipe, below the first one, doubles or triples your heat exchange area to harvest more heat out of the exhaust. Make sure the exhaust duct is always sloped downward - it doesn't need to be much - will keep the water that condenses out of the exhaust gases flowing toward the exit.
@joshuadelisle
@joshuadelisle 11 ай бұрын
Thank you. Great ideas. New video on it coming soon. Cheers J
@720millionlightyears
@720millionlightyears 11 ай бұрын
If he adds more pipe below the existing exhaust, then he will have to cut a new larger hole in the wall. Add the additional exhaust above and then redirect the first cm's coming out of the burner to the top of the new manifold, the exhaust is so hot there that no condensation is taking place at that point, only further down the manifold where it starts to cool down. And yes, all sloped downwards and where it starts getting hand hot, go to a smooth pipe for better air and moisture flow. Keep the muffler and exhaust outside also facing downwards
@Outside-In.
@Outside-In. 11 ай бұрын
I have one of these for emergency use, but haven't had the need to use it yet, but watching videos from actual users, helps me when I need to set it up. Thanks - Great Job 👍
@utha5034
@utha5034 Жыл бұрын
Thank you for referencing the cost of electricity to run this. Being thorough is greatly appreciated.
@jayeff3196
@jayeff3196 Жыл бұрын
Totally agree about the education thing....I have no issue tearing something down to its bare parts and putting it back together....just a bit inquisitive I think...I wanna know how it works and whats wrong with it...and can I fix it....always great videos Joshua....🙂
@alanhat5252
@alanhat5252 Жыл бұрын
around 1980 (in the UK) people suddenly stopped this sort of thing. I blame the Government.
@joshuadelisle
@joshuadelisle Жыл бұрын
Thank you so much. I hope it gives a good enough perspective on the possibilities. Cheers J
@napalmpig3772
@napalmpig3772 11 ай бұрын
I'd love to see how far this can be taken. You could use something like a Rasberry Pi to have a computer controlled startup and shutdown sequence that switches the fuel over. Add sensors and stuff to make it change settings to maximise efficiency. I don't know how to do any of that stuff so not sure how difficult it is.
@joshuadelisle
@joshuadelisle 11 ай бұрын
It's a possibility. Cheers J
@StrikeEngine
@StrikeEngine Жыл бұрын
If I'm not mistaken the manual says to keep the exhaust pipe to a maximum of 1 meter length. I believe it says this because any longer and the exhaust becomes a restriction leading to rich burn mixtures. If I were using a long exhaust like in the video I think I would use a much larger diameter pipe eg have the stock exhaust for a short a distance as possible and then step up to say a 3inch pipe. Run that 3 inch pipe indoors for as long a distance as possible and then vent outside. In addition to afrs staying correct, the exhaust gas will be slowed down massively (without causing a restriction) giving the exhaust gases more time to lose their heat inside the room.
@fishhuntadventure
@fishhuntadventure Жыл бұрын
But they sell 2-meter aka 8’ exhaust tubes for them. I have one…
@StrikeEngine
@StrikeEngine Жыл бұрын
@@fishhuntadventure but the manual says 24mm diameter and "at most 1 meter" length for the exhaust. (At least in the Vevor manual I have)
@onlythetruthfull
@onlythetruthfull Жыл бұрын
@@StrikeEngine That is for the rippled tube, best to use straight as much as possible Some Webasto use 32mm pipe. Some converters use far more than 1 metre.Just do not use copper its toxic at exhaust temperature.
@whirlybird996
@whirlybird996 10 ай бұрын
Thanks Joshua for taking the time to do this review, it was very helpful for my installation. Just a note to help anyone, I experience a rancid plastic like burning smell and I almost sent it back. Taking it apart it appears the manufacturer fitted a rubber anti-vibration pad where the exhaust comes out and this had charred. Doesn't look like its necessary in my application so I just removed it, problem sorted. I think ebay sell silicone replacements but they are quite expensive.
@joshuadelisle
@joshuadelisle 10 ай бұрын
Well done. I've got a new video coming shortly. Cheers J
@fongy200
@fongy200 Жыл бұрын
Just bought one Joshua, the exact same model. I recently built myself and son a new workshop. We were about to have a solid fuel Heater but after seeing these, decided against it. Thanks for showing me the way.
@joshuadelisle
@joshuadelisle Жыл бұрын
Well done. Cheers J
@Larsema1
@Larsema1 Жыл бұрын
Very interesting videos and experiments! The small electricity cost for driving glowplug and fan is adding as heat so its not wasted energy either. Next time you try to heat water with the exhaust, just make it spiral down the waterbucket/tank and lead it out in the bottom through a sealing so condensed moist can pour out.
@joshuadelisle
@joshuadelisle Жыл бұрын
Thank you. Great tip. Cheers J
@MrBianconeri90
@MrBianconeri90 10 ай бұрын
You can use old car EGR cooler to recover heat from the exhaust gas. Coolant can be used to heatup the heater and it is good to make a cooper hose coil over exhaust pipe to warm up oil
@scottyb6765
@scottyb6765 Жыл бұрын
Another great video Josh. I've been running my so called 8kw heater in my well insulated finished 12x24' shop. I had the pump turned up to the highest setting and it put out an impressive amount of heat burning red diesel but there was an distinct smell of hot or burning plastic... I never found evidence of any melted of burnt plastic but I turned the pump down and the smell diminished greatly. Yesterday I drained the oil from my diesel van engine so I will be mixing that used oil in with the diesel fuel at what I judge to be about 25% initially... aiming for 50% eventually. My unit is outside. Only the battery, the control, and the heat tube is inside. You could put a small 12v PC type fan on your exhaust pipe to push that heat out into the room. Keep up the good work - your video presentation is a very good mixture of tech and common sense. If you haven't already please warn people about the many different controllers being sold out there, how to identify them and the differences. Mine will not change from Celsius to Fahrenheit for US use, seems earlier and later models will. Cheers
@joshuadelisle
@joshuadelisle Жыл бұрын
Thank you so much. I'll do my best. You can buy the individual controllers if you want a different version. Cheers J
@scottyb6765
@scottyb6765 Жыл бұрын
@@joshuadelisle I'm mixing 25% waste oil into my red diesel now. The heater may actually be working better ( burning hotter) On this mix. What a great heater. Thanks again for all the info you posted on it.
@fmemories
@fmemories Жыл бұрын
They will all plug up eventually. Look at loweredexpectations. He tried so hard. They all plug up....
@hgvdweg
@hgvdweg Жыл бұрын
I have the same heater. It is standing outside the house. The heat comes in the house by means of a 70mm plastic pipe thru the wall. The pipe fits perfect inside the heat outlet. I use the most expensive diesel, BP Ultimate diesel at Euro2,02. I use this fuel because it doesn"t smell.(better for the neighbours).
@o.g.solutions
@o.g.solutions 9 ай бұрын
Waste oil collected eventually makes its way to bunkers along coastal cities. From there it is transfered to cargo ships where the mixed petroleum products including antifreeze,water ,metal shards , anything that can end up in a waste oil bin is run threw centerfuges and burned as fuel ,this "bunker fuel " can only be burned outside of international waters. The sludge filtered out is dumped at sea.
@totherarf
@totherarf Жыл бұрын
If you are trying to see how much you can squeeze out of the heater you might do well to make an airtight cowl around the exhaust pipe and run it into the air intake. Vent this to outside and you will pre-heat the air going into the heater. This would allow you to measure the heat gained, not that you would gain any more heat ;0) The difference in fuel usage could be down to the different viscosities of the different fuels. A great series of videos ..... please don't stop! Edit ...... Don't Try This! Read the comments below to see why not (unless you want to trash your heater control circuitry!
@joshuadelisle
@joshuadelisle Жыл бұрын
Good tip. Thank you. More to come. Cheers J
@oliver90owner
@oliver90owner Жыл бұрын
@@joshuadelisle Within their capabilities, these pumps are positive displacement type. If viscosity is reasonable and lift limits are reasonable, the volume pumped should be the same.
@bobsmith1101
@bobsmith1101 Жыл бұрын
You'll then be heating up the electronics where they are purposely placed at the cool air intake. I would perhaps design an additional heat exchanger round the exhaust system and then exit to outside. Put the squeeze on it!
@iIiWARHEADiIi
@iIiWARHEADiIi Жыл бұрын
Add to the viscosity, that oil canister was mounted higher than original tank, which creates extra pressure
@oliver90owner
@oliver90owner Жыл бұрын
@@iIiWARHEADiIi The design, as a parking heater could easily lift diesel from the vehicle fuel tank. The prescribed limits of fuel feed,from above or below, are in the installation instructions - those things that lots simply seem to ignore!
@hillonwheels8838
@hillonwheels8838 Жыл бұрын
For protecting your diesel heater from power outages you could get a 12v battery for a battery backup or mobility scooter and just put it inline. You won't be able to run for a long time but will be easily able to shut it down.
@dougle03
@dougle03 Жыл бұрын
He said that in the video.
@thehighwayman78
@thehighwayman78 Жыл бұрын
Nice video, great experiment! I love my car's Webasto. So nice to program a starting time and go sit in a warm and defrosted car in the morning when it's -20 outside, and it's so much better for the engine. It runs off of my petrol tank, my car is a CNG/Petrol hybrid, and I've wondered why it doesn't use CNG instead of petrol. I guess there is a reason for it.
@THEOFFGRIDMOUNTAINHOMESTEAD
@THEOFFGRIDMOUNTAINHOMESTEAD 10 ай бұрын
Thanks for the video! I’m going to fire off my first diesel heater soon! Got plenty of old recovered diesel and plan to make biodiesel.
@davidparr5780
@davidparr5780 20 күн бұрын
Sorry I’ve been a little bit critical, however; really good job. We are all learning from this.
@sandmanbub
@sandmanbub Жыл бұрын
You can make a cheap and effective vacuum filtration system with a plastic 5 gallon bucket, a small vacuum pump, a hose and fitting for the bucket and funnel shaped screen that fits the top of the bucket. Made one for doing something similar to what you're doing with the used cooking oil.
@joshuadelisle
@joshuadelisle Жыл бұрын
Thank you. It also best to cut it first with kerosene if that's the intention as it makes it far less viscous and easier to pass through. Cheers J
@kde5fan737
@kde5fan737 Жыл бұрын
@@joshuadelisle a 10-20 degree temp increase does wonders as well, let alone heating it to 100-130C
@You-can-fix-it-yourself
@You-can-fix-it-yourself Жыл бұрын
Be careful with the line power mounted above the power supply. A piece of tin as a heat shield will prevent any melting of the insulation. You have put together an excellent video, thank you very much for posting this.
@joshuadelisle
@joshuadelisle Жыл бұрын
Thank you so much. Cheers J
@ralphfell2119
@ralphfell2119 Жыл бұрын
Interesting video. Just for your information there are two types of heating oil on the market, Kerosene and 35 second gas oil, both meant for oil fired central heating. The 35 second gas oil is the same viscosity as diesel so will not affect the wear on the pump. I have fitted my exhaust to a small central heating radiator and will let you know the results over the next few months, I have also upgraded the air cleaner and exhaust silencer and have fitted it very similar to you set up.
@shaunshepherd9097
@shaunshepherd9097 Жыл бұрын
I appreciate your time and effort. You definitely have put a lot of work into this!
@Because_Im_Ace
@Because_Im_Ace 2 ай бұрын
US based chef here, a lot of our restaurants have contracts with biodiesel companies. The cooking oil may not actually be owned by the restaurant it’s basically leased and a restaurant may be fined if it’s production of WVO starts to drop.
@EmptyBottleDesigns
@EmptyBottleDesigns 2 ай бұрын
Wow. I've got the same heater in my garden shed, but I'm sure mine isn't running at least half the efficiency of Joshua's. I definitely subscribed, as I'll be learning how to run my heater more cheaply and efficiently in the future. Cheers mate.
@InsidiousDr9
@InsidiousDr9 Жыл бұрын
The heat-pump is actually better than 100%. It depends a lot on ambient - but I'm guessing is temperate where you are so say 250%. But of course the initial price is much higher than this contraption (although it also works as air-con / however useful that is in your climate).
@matthewmcauley7982
@matthewmcauley7982 Жыл бұрын
Heat and air guy here, the water you poured out of exhaust is the acidic condensate you mentioned at the beginning of the vid
@Berniessen
@Berniessen 5 ай бұрын
I use the same chinese Vevor diesel heater to warm a office unit (basicly a well isolated shipping container with windows and a door) and i replaced the window with plexiglass plate and i have the heater outside in a big plastic box outside. I drilled 2 large holes in the plexiglass one for mounting the hot air coming in and one for getting rid of the over pressure,and that hose leads back to the rear of the heater in the plastic box. This setup works great no sound and lovely warm air getting in......In like 15min the unit is warmed up alot as its size is only outside diameter 6x2,5x2,2meters and the wall are 40mm isolated and the roof 60mm. Electric heating cost me alot (but a 3kw electric heater heats the place up super fast aswell).....Propane worked well but everything inside got wet from moisture and u need ventilation...................But this diesel heater cost nothing........Like 150ml diesel a hour for 4 5 6h a day lets say.......1€ a day i was sitting inside with 22-24 degrees working.... I really like these diesel heaters........ cheap vs electic and uit to run and pumping out some nice dry heat vs propane.
@jagmarc
@jagmarc Жыл бұрын
A generic O2 sensor permanently installed in the exhaust gas flow may be useful. Not to control anything, just to view its mV output.
@BobPackard
@BobPackard Жыл бұрын
Run the exhaust extension as a straight piece of pipe, but running downhill to the exit through the wall, self draining condensate. Combine all the suggestions of putting a copper shroud around the exhaust, and have THAT pipe with its air inlet quite a bit lower than its outlet, thermal action does the rest. (Bob Packard)
@bertjesklotepino
@bertjesklotepino Жыл бұрын
can you perhaps show a picture or drawing of what you have explained? I am dutch and it would help a lot to understand what you mean to say.
@vaporainwaves
@vaporainwaves Жыл бұрын
@@bertjesklotepino Steam condensates inside exhaust to water when exhaust is suddenly cooled below 100c. (water, sand battery etc.) If you run the exhaust with proper downfall, the water inside the exhaust can simply drip out the end and not clog the exhaust.
@mcgam2000
@mcgam2000 Жыл бұрын
As most petroleum based fuels combust, a by-product is water vapor... And since you were cooling the exhaust with the water, the water vapor was condensing in the tube. And since the exit pipe was not at the lowest point, it started collecting in the pipe. as already mentioned...
@jimsarranadventures3005
@jimsarranadventures3005 9 ай бұрын
That’s, very informative video. I’ve been heating my workshop for the last 3 years burning kerosene and only stripped the heater down recently, no issues. I have a 220ltr drum that gets filled up at the same time as my domestic tank, works fine for me. Will be trying out the veggie oil mix. Cheers.
@joshuadelisle
@joshuadelisle 9 ай бұрын
Well done. Cheers J
@whatleft123
@whatleft123 10 ай бұрын
I own a restaurant and have been collecting oil, we filter the oil everyday, but on the day we change the oil it goes straight to the jug. But gravity does an amazing job of filtering. I just slow pour the jug and try to keep all the solids on the bottom. I have so much oil mine can sit for a month. One lesson I learned is, don't let those jugs sit in sun light, they deteriorate rapidly, and crack easily. No more than a month at most. I did have the state bother me at one point and I provided them studies that vegetable oil in less than 50% concentration actually helps the soil and is not a pollutant. However, they still made me keep my oil on concrete.
@PaulSmith-jr1qe
@PaulSmith-jr1qe Жыл бұрын
I use a 5KW heater in the greenhouse and when I extended the exhaust as you have I had problems with it not burning clean presumably through the back pressure not allowing it to clear the fumes quick enough , I then used a 10 foot length of 42mm copper tube as the exhaust. This runs the full length of the greenhouse and as it exits it is still too hot to put your hand on it without getting burned, however it runs much cleaner. The point being the soot build up you experienced may be due to exhaust restriction rather than the fuel. It might be worth experimenting with say a length of scaffold tubing it's easy enough to fabricate a connection with the gear you have.
@joshuadelisle
@joshuadelisle Жыл бұрын
Great information. Thank you. Cheers J
@wrxs1781
@wrxs1781 Жыл бұрын
Where I live it frequently can drop to -18C (Canada) for my daily use the fuel is 50/50 diesel kerosene, exhaust short as possible on a downward angle. My needs are primarily heat, but the mods are ingenious and informative. The cost of energy in the UK to me is staggering, luckily you live in a temperate climate.
@joshuadelisle
@joshuadelisle Жыл бұрын
@@wrxs1781 I just found out we buy a lot of Canadian trees to fuel biomass energy in the UK. To me that's crazy. Cheers J
@jasonmorehouse3756
@jasonmorehouse3756 Жыл бұрын
This is correct thinking. If you increase the length of the exhaust on these heaters or use more than 4 bends, you have to increase the size of the pipe.
@wrxs1781
@wrxs1781 Жыл бұрын
@@joshuadelisle As in wood pellets, many people heat with wood pellets "pellet stoves" "compressed sawdust pellets, and corn stoves, using corn kernels. People out of the cities heat with wood, or propane.
@purelife9000
@purelife9000 Жыл бұрын
I immediately bought the 8kw version on your recommendation and I am looking forward to using it. Keep up the supply of great content, sir!
@joshuadelisle
@joshuadelisle Жыл бұрын
Well done. Great investment in my opinion. All the very best. Cheers J
@RN-SM-SSBN04
@RN-SM-SSBN04 Жыл бұрын
there is no 8kw. they say it is but its only a 5kw. kzbin.info/www/bejne/ZqCWaYuBp7mFoas it is all explained in that vid link
@SynKronos
@SynKronos Жыл бұрын
No offence to the video creator but there are quite a few issues here. So be careful. This video is not accurate. And as another has stated the maximum output of an 8kw is around 5 in the real world, including exhaust recycling. I would also factor in for solar charging personally. Making vids currently on the subject. I am a retired experimental physicist/ engineer if that helps.
@tommay2561
@tommay2561 Жыл бұрын
8kw ? or output 5kw.... unless quality. cheap 1s max 4\5 if lucky advis. gimick : see specification / build
@Critters
@Critters 11 ай бұрын
Maybe run the exhaust through a bucket of sand. Sand wont evaporate or go nasty, and will hold the heat. It could also go above the boiling point of water. Maybe even use a trough of sand, then you could have the pipe just do one bend and loop back and have it with a gradual downhill gradient to have any condensing drip out the end.
@joshuadelisle
@joshuadelisle 11 ай бұрын
Video coming up. Cheers J
@paulbrown521
@paulbrown521 11 ай бұрын
Great video , mix the kero with wvo and shake for a few minutes then filter it thro 1 micron filter , filters a lot faster .
@traFREAK
@traFREAK Жыл бұрын
I love this, never studied engineering myself but was always very interested in it. Cool projects like these that will save you some money in the end and teach you a lot are great and i cant wait to try this myself. Thanks Joshua!
@eveningecho5334
@eveningecho5334 Жыл бұрын
Burnt oil…. Just saw a vid from MartyT in New Zealand, using a centrifuge to separate oil from its contaminants to in theory turn knackered oil back into new usable oil. Interesting concept. His results were mildly positive but I think the e setup was a little cruder than what you’d need to produce good results. Seems like something you might be into so!
@johnmonk66
@johnmonk66 Жыл бұрын
With the exhaust being so hot, i would loop it through a metal box first, then the metal box can have an exhaust fan, the inside of the box will get hot and you get more heat. Or run the exhaust through baseboard heating, the fins would give off heat before the hot air is exhausted to the outside. The idea is to send as little heat outside as possible, and keep as much as you can inside.
@lemoinexavier
@lemoinexavier 10 ай бұрын
I'm 52 now and just recovered the new Mc. Giver! Thank you for your vids!
@ammej768
@ammej768 Жыл бұрын
I bought the combustion unit without the metal enclosure. It included a kit of parts and a 20l fuel tank . It works fine. I used it for heating a double garage. Not very well insulated, I mounted it in a small external garden storage unit. The air is drawn from inside the garage through the intake end and heated air blown back from the exhaust end. The inlet and exhaust for the combustion process are, of course, kept outside. The air in the garage is gradually warmed and recirculated through the heater, so I'm not heating cold air all the time. I found the whole business of going to the garage every couple of days a bit of a pita. Its a smelly business carrying diesel in 5 litre containers.. Mine was the '8 kw' version that looks exactly like the one in your video. I was getting through 2 litres every 6 hour day!!
@dougle03
@dougle03 Жыл бұрын
I'd say your garage was losing a lot of heat. Insulate the tin doors, insulate the walls and improve the door seals. You want some ventilation in a garage, but most allow the wind to blow through...
@marcbolducrealestate
@marcbolducrealestate 10 ай бұрын
I just want to say, this video is excellently well done! it’s understandable but takes into account all of the variables and delivered as if we’re solving a mystery. A+ content right here! Sincerely thank you for the video!
@joshuadelisle
@joshuadelisle 10 ай бұрын
Thank you so much. Cheers J
@m1geo
@m1geo Жыл бұрын
Really interesting video. I have a heatpump in my workshop. An air-to-air minisplit. Works great for heating, but lacks some oomph in winter! Definitely considering one of these for the workshop! 😁
@wilsonwombat3456
@wilsonwombat3456 Жыл бұрын
For a heat exchanger run the exhaust through a pipe filled with sand. (1kg sand heated to 40c will take @ 5.5 hrs to drop down to 20c.)
@b.saulius3916
@b.saulius3916 Жыл бұрын
i wonder does it mather what kind of sand, like with smaller particals ?
@PeterJavea
@PeterJavea Жыл бұрын
10/10 for a great video I run mine in our heating oil and, like you recommended, use a small 12v good condition deep cycle 22 ahc battery with a trickle charge. The battery has the umff to get it all started, the trickle charger keeps it all going and recharges the battery back up.
@godzillas6301
@godzillas6301 Жыл бұрын
TY . Im considering this and this is the exact way i was thinking of keeping it going . TY for letting us know it works .
@PeterJavea
@PeterJavea Жыл бұрын
Another thing I did during the fall here was to service it. Lots of films on YT showing that. I also bought "everything" I'd need to maintain, repair or replace. Like a spare glow plug and 2 tools pump, the gaskets, and of course a bag of the atomisers that I replace. That way IF something goes wrong in winter or during servicing, I can deal with it directly. I learned a lot if stuff about heating through this project.
@oriolpascualoliver8574
@oriolpascualoliver8574 Жыл бұрын
Hi Joshua, first of all, congrats for your videos, I'm a big fan of your metal working videos and experiments. Regarding this topic, I would recommend you to get an EGR cooler (from a diesel car, to cool the exhaust before reentering to the combustion chamber) that way you will get a propper made gas to water heat exchanger. Thanks for your effort!
@joshuadelisle
@joshuadelisle Жыл бұрын
Thank you so much. Great tip. Thank you. Cheers J
@knobon
@knobon Жыл бұрын
@@joshuadelisle been told a 2006 ford Galaxy is a straight bolt option as the hole sizes match the exhaust
@rayhsetwo8594
@rayhsetwo8594 Жыл бұрын
Waste veg oil apparently soots these up quicker, but you can strip it down and clean, and buy the mesh injector in packs of ten. To recycle the used cooking oil quicker there's a video whereby they put gelatine powder or something like that and it drags all the burned impure waste to the bottom of container and then filter. Supposed to be the quickest way to do it.
@peterkelsey1299
@peterkelsey1299 Жыл бұрын
Here's the link to what your saying 👍kzbin.info/www/bejne/kIvKZ5ufp9BsqJI
@joshuadelisle
@joshuadelisle Жыл бұрын
Great idea. Cheers J
@peterkelsey1299
@peterkelsey1299 Жыл бұрын
@@joshuadelisle great work Joshua 👏👏👏👍
@MyMy-tv7fd
@MyMy-tv7fd Жыл бұрын
good idea wtih the gelatine, most biodiesel processes gravity settle then filter/double filter dirty waste veg oil. I wonder if glycerine (from the actual process of producing biodiesel) would also work to flocculate the sediment quicker?
@rayhsetwo8594
@rayhsetwo8594 Жыл бұрын
@@MyMy-tv7fd glycerine, I believe so, but not done it myself, but I think there's some videos on YT with glycerine being used.
@asdf35750
@asdf35750 Жыл бұрын
Ummmm, Josh, energy is measured in Joules (1 Watt second, although more frequently Kilojoules) or BTU (1055 joules), both of which can be converted by scaling them into kilowatt-hours. Kilowatts are a measure of power, not energy. So a heater that runs at a power output of 8 kilowatts will produce 8 kilowatt-hours of heat in 1 hour. 8 kilowatt-hours is 28800 kilojoules, or about 27300 BTU
@arliewinters2776
@arliewinters2776 11 ай бұрын
My Good Man...I just found your vids today...love the reports on the oil burners ! I have a comment...it is about burning kerosene as opposed to diesel. I have read / heard that kerosene does not have the lubrication properties of diesel. This may be why you noticed a quieter sound decibel difference when switching from starting with kero, then switching to veg-oil. I have also read / heard that using kerosene will shorten the life of the pump because of lack of lubrication....because the pump is a piston...metal on metal piston. Just an observation. Absolutely love this stuff !!!
@joshuadelisle
@joshuadelisle 11 ай бұрын
Thank you so much. Kerosene is designed specifically for heating. I'm making another video just now on the same heater as a kind of 12 month review. If the pump does fail they are only £15 to. Replace. I buy kerosene at £0.60 per litre so as you can imagine I'm saving a lot of money even if I have to buy a new pump every year. Cheers J
@MarkAAshdown
@MarkAAshdown 10 ай бұрын
Good video- 1-historically you were correct in stating that a kWh of electricity costs a certain price and that they directly correspond. However this is no longer true with the new tariffs available. Its now possible at certain times to import electricity at night for 7.5 p per kWh or Zero p per kwh and or even get paid to import it! if you have a battery , you can even store electricity at these rates. 2 - how much have you allowed in the cost calculations for fuel etc used in picking up the waste oil? 3 Thermally one is better off bringing in cold air from the outside as cold air has more oxygen molecules per unit volume due to its higher density, rather than burning already heated air internally and then exhausting that already heated air. Really enjoyed the video - thank you
@WeeSecure-uk
@WeeSecure-uk Жыл бұрын
I enjoyed this video a lot, quite inspiring. I plan to augment the exhaust heat recovery design further with a DIY heat exchanger and combine this with an air source heat pump. To maximise heat recovery and efficiency, I will split my exhaust into 2 using 3/4" BSP 3 way cast iron female tee (3/4" bsp measures 1" inside), then slip a dozen copper coated scourers around outside of each tube, encase the whole thing in a metal duct and use a separate air input to be heated by the exhaust and feed the warmed air into an air source heat pump. The heated air will enter the cold side of the heat pump and wont be used for the clean air input, [for safety] just to ensure any exhaust gas leakage does not enter indoors. Running the oil heater on minimum Hz, I hope to be able to a) recover the most heat possible from the oil heater and b) be run the heat pump in a temperature range [in winter] where it works most effectively. Hopefully will produce a lot of heat at minimum £/KWh ;)
@joshuadelisle
@joshuadelisle Жыл бұрын
That's awesome well done. I'm making another combo to go on my house as a window module. It'll heat an external hot water tank which can be used for central heating, showers etc.
@madaboutimps
@madaboutimps Жыл бұрын
2 options, fit a braze plate heat exchanger to ur exhaust you can then heat ur water plus use as a preheat for your kero. BPHX are reasonable cheap from china
@silasdkdkdkdk
@silasdkdkdkdk Жыл бұрын
you should try running the exhaust through a normal water radiator. With the inlet in the top and exhaust out the bottom, so moisture can drain out with the exhaust.
@b.saulius3916
@b.saulius3916 Жыл бұрын
are these exhaust pipes prone to corosion ?
@nicolaf970
@nicolaf970 Жыл бұрын
I’ve been running a Chinese diesel heater running heating fuel (kerosene) for close on 5 years and no issues. ❤
@stumccabe
@stumccabe Жыл бұрын
Just a comment on units. The scientific unit of energy is the Joule (J). Power is the rate at which energy is produced or provided, that is Joules per second; 1 Joule per second we call a Watt (W). A kilowatt (kW) is 1000 Watts. Note Watts and kilowatts are units of power, not energy. Power x Time = Energy. So the commonly used unit of energy (apart from the Joule) is the kilowatt hour (kWh). Electrical energy is sold in kilowatt hours, not kilowatts!
@dotpeat1372
@dotpeat1372 Жыл бұрын
Great stuff! Worth watching (&subscribing)... Saved my frying oil(for making oliebollen) and wanted it to mix it in with regular diesel and also the latter to be replaced by kerosene. When running your diesel car on veg oil, it was advised to just mix a little methanol in it as the viscosity is lower which could create starting problems. I would just run with 'blended' fuels. It looks we are going back to the old times, making our own fuel to stay independent! It was also the reason as why mr Diesel invented the diesel engine (only rich people could afford patrol cars). The whole reason why governments want to get us electric, to take our liberties. Anyway, great upload, looking forward to your next one!
@joshuadelisle
@joshuadelisle Жыл бұрын
Yep I totally agree. Im working to be independent from the government and corporations. Cheers J
@dougle03
@dougle03 Жыл бұрын
Stay away from methanol; fantastic but horrible at the same time. A fella near me died a few years ago when his shed where he mixed his diesel car fuel exploded. Also, Methanol burns without a visible flame, it's really not pleasant and best avoided...
@michaelhannon2452
@michaelhannon2452 11 ай бұрын
Brilliant well made video with everything you need to know. As a heat source it's fantastic and cheap running in comparison to a kerosene heat blower for a workshop and you can still hear yourself when talking with this system. Very interesting topics we'll worth subscribing, cheers for all the information 👍
@joshuadelisle
@joshuadelisle 11 ай бұрын
Thank you so much. I'm currently working on another video of diesel heater with subscriber suggestions and mods. Cheers J
@matttradie1341
@matttradie1341 Жыл бұрын
Wrapping a coil of copper and then insulation around the exhaust would be far safer. Work on that hot water rises to avoid pumping it if you can, also get a pressure vessel that u can pressurise with the compressor to force the oil through to filter it. Perhaps modify a beer keg or an old compressor tank etc. also does your backyard smell like a chippy now? Lol
Unfiltered 100% Waste Oil Vs Stock Diesel Heater
19:38
SteinFab Garage
Рет қаралды 337 М.
Try Not To Laugh 😅 the Best of BoxtoxTv 👌
00:18
boxtoxtv
Рет қаралды 7 МЛН
Smart Sigma Kid #funny #sigma
00:14
CRAZY GREAPA
Рет қаралды 90 МЛН
У вас там какие таланты ?😂
00:19
Карина Хафизова
Рет қаралды 14 МЛН
UFC 308 : Уиттакер VS Чимаев
01:54
Setanta Sports UFC
Рет қаралды 870 М.
(2024) Super Cheap heating tips💲+ Underfloor heating mod🫠
49:55
Joshua De Lisle
Рет қаралды 32 М.
Everything You Need to Know About Diesel Heaters
38:19
dusty odyssey
Рет қаралды 41 М.
Diesel heater upgade 200% more efficient
16:39
D&S Farm NS
Рет қаралды 357 М.
DIY INFRARED HEATER | No Electricity Needed For Greenhouse Heat
15:48
Zen Garden Oasis
Рет қаралды 1,5 МЛН
The Best Thing Since Sliced Water - Chinese Diesel Heaters. PT-2
33:48
Lowered Expectations
Рет қаралды 46 М.
2000 HOURS LATER! Chinese Diesel Heater
24:55
Mispronounced Adventures
Рет қаралды 500 М.
DIY Vevor Diesel Stove with  Free Energy Sand Battery
15:49
Rickards Garage
Рет қаралды 852 М.
Try Not To Laugh 😅 the Best of BoxtoxTv 👌
00:18
boxtoxtv
Рет қаралды 7 МЛН