Installing the JG Speedfit Underfloor Heating Manifold

[@muhammedsonko4616]

it's so nice. I learn a lot from these hope that I will do it practically one day.

[@TheLife0025]

Please show us how to connect the left side of the pump where main flow and return pipes will be installed. This part comes with 22mm x 3/4 Male compression. But if we have 16mm UFH pipe then there is no reducer from 22mm to 16mm available. how do we connect 16mm pipes to flow and return.

[@nallekarhu7994]

How does it interact with the boiler, I mean hot water in, gives off heat then get reheated, and back into system then....

[@coord47]

I have UFH with this JG manifold operating with a flow of about 50C. What should the mixer valve setting degreeC be during normal operation?

[@memo007999]

Nice explanation thanks

[@kenney5454]

Good looking bits, nice explanation

[@houcinlgzal6442]

👍Gods djoupe

[@superdau]

Do you really run 60°C through your underfloor heating? In our installation a safety switch cuts out all pumps if the temperature should ever go above 40°C (water is mixed near the pump in the basement). Typically it runs between 30 and 35°C.

[@emanueliancu]

Max 45. But yeah, 60 it s way too high

[@chavezgutijulia1]

Que funcion tiene. Saludos.

[@tradingdepot]

We have plenty of helpful videos available on our Trading Depot KZbin chanel, offering better insights into the products on our website. Here is a handy step-by-step video on how to install a John Guest Speedfit manifold. The JG Speedfit manifold kits can be used on both underfloor heating & radiator based systems. They are available to purchase online from Trading Depot here: goo.gl/djYq8o

[@walterknobloch3022]

do you have a supplier in Canada?

[@momciloslavicin2500]

Trading Depot l

[@Order-in-Chaos]

Why fill the loop **then** pressure test? If after filling the system it is pressurized then if there's a leak somewhere the pressurized water will cause damage... Air testing should be done before filling.

[@liliput50]

very helpful thank you

[@rogerharrison8195]

Hi - my system worked fine until I messed up when I made a change to the Aura wireless thermostat. Now the UFH works but I can't get the radiators to come on (these do not have thermostats on each radiator). I must have set up the two aura thermostats wrong, but can't work out what settings I need to enter after reboot.

[@jamshidochilov8108]

Zor

[@abdullateefoyeneye3562]

I live in Nigeria work on plumbing system technics

[@sheledmikymo]

shut off valves need to be before the pump, not after

[@timorum]

Is there an installer/agent for these systems in new zealand? thanks

[@tradingdepot]

Tim Orum Hi Tim, You would be best directing that question directly to Speedfit themselves. You can reach them here: www.johnguest.com/contact-us/ Kind regards, Trading Depot

[@StoutProper]

Tim Orum just do it the other way round

[@هيماالاسواني-ح9خ]

الله ينور يامعلم بس عاوز سوال منك ممكن

[@NevilleAWilson]

Boiler thermostat cutting out frequent,ly what are the possible reasons

[@tradingdepot]

Hi Neville, Unfortunately we aren't technically trained on the product here. You would best directing this type of query to the technical team at JG Speedfit. www.johnguest.com/speedfit/technical-support/ Or by phone: [phone] Kind regards, Trading Depot

[@charlieorteaga9217]

que buen video

[@istabrakofficeistabrakoffi8575]

bravos

[@jeanmarciempaszak9972]

Le plancher chauffant est d’un autre temps maintenant, il y a nettement mieux à présent.

[@bghkillerful]

Devitis Deavitis

[@jeanmarciempaszak9972]

Le plancher chauffant est d’un autre temps, il y a mieux maintenant.

[@ramdaouiboudjemaa8123]

plaise ..if you can..trading in arabic

[@DR-mp4gv]

push fit connections.... meh

[@mustafakazdar6413]

n

[@maram300maram7]

س

[@حسينالتميمي-ع7ي]

ا الغرب وين والعرب وين