Installing throttle on 212cc predator pt2

  Рет қаралды 57,788

BROKE RICHGUY

BROKE RICHGUY

Күн бұрын

Пікірлер: 37
@rodclark2964
@rodclark2964 4 жыл бұрын
holy fuck,thank u...been searching for a vid like this for ah hour
@BROKERICHGUYog
@BROKERICHGUYog 4 жыл бұрын
glad it helped man.
@jucotesting5623
@jucotesting5623 8 жыл бұрын
I'm having trouble figuring out why the cable won't move within the sleeve.
@BROKERICHGUYog
@BROKERICHGUYog 8 жыл бұрын
got it figured out yet?
@joelopez3639
@joelopez3639 3 жыл бұрын
The plastic part is broken where do I get the replacement?
@BROKERICHGUYog
@BROKERICHGUYog 3 жыл бұрын
probably easiest to get a new carb. or check ombwarehouse or nrracing to see if there are replacement parts.
@shagnasty115
@shagnasty115 7 жыл бұрын
On the 212cc predator motor is the start arrow choke on? And run arrow choke off?? Because I have a mini bike with a 5.5 Honda motor on it and run is choke on and Start is choke off! If someone would plzzzzz let me know.
@BROKERICHGUYog
@BROKERICHGUYog 7 жыл бұрын
yes, to start it put the lever towards arrow, when it starts put it to run.. then go tear up the streets.
@shagnasty115
@shagnasty115 7 жыл бұрын
Ok. It was pretty cold here in Ohio today. Cuz I turned the choke lever to run and turned the fuel valve to on and let it run for a good 5 plus mins and when I went to move the choke lever back to the start pozision it shutoff.
@BROKERICHGUYog
@BROKERICHGUYog 7 жыл бұрын
most likely a plugged jet in the carb or an air leak somewhere between the carb and the engine.. if the motor has been sitting for a bit its probably a plugged jet.. do a carb clean and you should be good to go..
@shagnasty115
@shagnasty115 7 жыл бұрын
This is my 3rd time running it to break the motor in. I just got the motor Brand New from harbor freight on the 1st on December
@shagnasty115
@shagnasty115 7 жыл бұрын
My kart looks just like Johns from carsandcameras! Not like that has anything to do with the new motor.
@bombo-pr6669
@bombo-pr6669 8 жыл бұрын
did you take the governor out of the motor or just disconect it from the top
@BROKERICHGUYog
@BROKERICHGUYog 8 жыл бұрын
I rec.to fully take it out...
@stevec.5774
@stevec.5774 7 жыл бұрын
I replaced my stock carb & filter with a bored carb & paper filter. The new carb does not have a spring on top (like the orig had) which brings it back to idle when I let off the gas. With the new carb installed, this rod you're bending keeps the carb at full bore. Gov is NOT removed. When I apply pressure on the rod to keep the carb at idle, everything works as it should when I apply throttle. So can I use this same method you did in this video, to fix my problem & get on with my life??
@BROKERICHGUYog
@BROKERICHGUYog 7 жыл бұрын
Steve C. yes you can for sure just use springs to make the throttle return to idle when you let off the throttle. you can also drill a tiny hole in the plastic throttle piece that the rod goes in and connect a spring in that and connect it somewhere that it will be pulling the throttle back to the idle position at all times.
@stevec.5774
@stevec.5774 7 жыл бұрын
thanks man... new at this
@JuanLopez-sp9ye
@JuanLopez-sp9ye 6 жыл бұрын
Do i need to remove the governor to put this on my kart? I bought a kart and when i push the pedal , the throttle cable attaching plate moves but my engine does not give acceleration. What can be the problem?
@JuanLopez-sp9ye
@JuanLopez-sp9ye 6 жыл бұрын
I bought it from someone online and the engine sounds good , nothing sounds bad . The kart did not come with a driver belt that fit so the motor cant spin the wheels but the actual motor works and spins . But like i said im not sure why when i press on pedal and the throttle attaching plate moves like its suppose to , the engine dont give power or a roar . Please help me . I dont see the carburetor move
@JuanLopez-sp9ye
@JuanLopez-sp9ye 6 жыл бұрын
And i dont know if the previous owners removed the governor, so im not sure if its safe to add the throttle in the video if in case my engine still has the governor. Please help!!
@BROKERICHGUYog
@BROKERICHGUYog 6 жыл бұрын
This is for a motor with the governor removed.. . I've seen people take off the governor arm or tie it back and then do this.. but I recommend to fully remove govornor from inside of motor and plug the hole and all that good stuff.
@JuanLopez-sp9ye
@JuanLopez-sp9ye 6 жыл бұрын
Thank you and i heared that if you remove your governor, you should install a better valve or something . Can you fill me in on that please
@BROKERICHGUYog
@BROKERICHGUYog 6 жыл бұрын
Juan Lopez basically if you remove the governor your motor can and will overrev. It will cause valve float and you can drop a valve or break a rod or rod bolt. That's pretty common if you hold it wide open for more than 5 to 10 seconds at really high rpm.. if you remove governor I would recommend at least putting better valve springs,retainers,flywheel and rod in your motor.. then they will last quite a while.. those are the main weak links in an unrestricted motor.. but I have a few buddies that have ran ungovorned motors for quite some time without blowing them up and without all the add on parts but you just don't wanna hold it at full speed for more than a few seconds.. but you can go to places like nrracing or omb warehouse online and buy a stage 2 or 3 kit that would help support an ungovorned motor.. in one of my videos I have a vid of what happens to ungovorned motors when you rev em to the moon for too long..
@grenadelaunchin3631
@grenadelaunchin3631 6 жыл бұрын
So how do you hook the cut off cable to the engine ?
@BROKERICHGUYog
@BROKERICHGUYog 6 жыл бұрын
There is the little barrel with a screw on top that you loosen up and stick the cable through the little hole and then you tighten the little phillips head bolt and it pinches down on the cable and holds it in place.
@macblaze4223
@macblaze4223 6 жыл бұрын
Ok so I didn't remove the governor I just attempted to run the throttle cable directly to the governor lever, but once I tightened up the screw that holds the throttle in place, it won't snap back like it should.. can anyone let me know what I'm not doing right?
@BROKERICHGUYog
@BROKERICHGUYog 6 жыл бұрын
you cant connect ur throttle cable to the govornor arm directly.. you can make the lil piece here that i showed and then you wont have to deal with the govornor lever at all.
@mxtoxkiron9437
@mxtoxkiron9437 5 жыл бұрын
Same
@chancemiller2584
@chancemiller2584 8 жыл бұрын
this is with the govenor removed right?
@BROKERICHGUYog
@BROKERICHGUYog 8 жыл бұрын
correct.
@terrikachyna2
@terrikachyna2 8 жыл бұрын
How much mph does it go?
@BROKERICHGUYog
@BROKERICHGUYog 8 жыл бұрын
not too sure on this one tbh with you.I have a few vids on my channel of a few of my bikes that do 70mph
@avaleecrawford1267
@avaleecrawford1267 8 жыл бұрын
thx this helps me
@BROKERICHGUYog
@BROKERICHGUYog 8 жыл бұрын
Glad to help.
@ohyeahguy
@ohyeahguy 8 жыл бұрын
you sound like Owen Wilson the actor skater dude
@BROKERICHGUYog
@BROKERICHGUYog 8 жыл бұрын
Lol
@BigRichardsGentlemensClub
@BigRichardsGentlemensClub 7 жыл бұрын
You described literally nothing about how to do anything. Spike of millions of ways to do it and didn't even describe in any detail about what you were doing and what needs to be done.
Predator 212 - Series 30 Torque Converter Install: The SMOG Project 05
27:49
Doktor scott Diabolical - Evil Genius
Рет қаралды 298 М.
Hooking up mini bikes throttle pt 3
7:08
BROKE RICHGUY
Рет қаралды 43 М.
Леон киллер и Оля Полякова 😹
00:42
Канал Смеха
Рет қаралды 4,7 МЛН
Каха и дочка
00:28
К-Media
Рет қаралды 3,4 МЛН
BAYGUYSTAN | 1 СЕРИЯ | bayGUYS
36:55
bayGUYS
Рет қаралды 1,9 МЛН
How to bypass governor on a predator 212
8:35
Random Builds
Рет қаралды 27 М.
how to bypass the governor on a predator 212 engine
9:11
rather B welding
Рет қаралды 1,9 МЛН
Predator 212 Throttle Linkage
7:59
Keith Doerr
Рет қаралды 236 М.
Predator 212/GX200 Go Kart Throttle Linkage With Removed Governor
14:11
Red Beard's Garage
Рет қаралды 233 М.
Go Kart Throttle Cable: Linkage and Installation
2:49
KartFab
Рет қаралды 371 М.
Installing generator to a 212 predator engine to power lights
6:35
Predator Ghost Mini Bike Build! The Ultimate Pit Bike! *Race Engine*
32:28
How To Install a Throttle Cable on Any Small Engine
5:46
Fix It Now
Рет қаралды 181 М.