Instant Fix Xbox Elite Series 2 Drifting Issue.

My controller analog stick was drifting upwards and I was looks everywhere to find a fix. I opened it up and after many attempts and even breaking the controller (I was able to fix it) I found out this trick.
Hope this helps!
Tags:
Xbox controller Deadzone issue Fix
Xbox controller stick drifting
My xbox controller is drifting
Xbox controller not working
Xbox Elite series 2 controller fix.

[@gabrielvaz2461]

Really appreciate the positive results from you guys. I had an extremely bad drift and wasn't finding out how to fix it until I found this simple trick. Note that from time to time the drift goes back, and to fix it just open up the controller again and play with the sensors as I did. Thanks, Guys! :)

[@myhug6131]

If you put a small thin piece of paper in between the green plastic piece and the analog stick and then push the green plastics piece in all the way and it stays

[@GOATGamerProSticks]

Good stuff you might find this info drop usefull on Analog stick form factor i just put together. kzbin.info/www/bejne/paSnnWtsabiZjMk Ive yet to finish my potentiometer study vid because its mind numbingly boaring to do but it should be informat lets hope :^)

[@KennyNiii]

Does the stick drift come back sometimes? Or has it been gone for good (until now)? Great vid!

[@YoungTarzPlays]

just buy a new controller this is too much effort 😭

[@williemcwhirter606]

@@myhug6131 I just did this method, it WORKS! I did what the video suggested and the drift was back in few minutes, so I decided to put thin paper in, and behold! No more drift, this is AMAZING! Thank you thank you!

[@Speleogoupil]

My 17 year old son was asking me to replace his controller, because of that issue. We had tried a cleaning, using compressed air, which did not change anything. When I found your video, he tried your trick and everything came back to normal instantly. It was jaw dropping for him, and I was proud to tell him that searching a bit more for a repair solution, can be rewarding. Thank you so much for making and sharing this well made video! Two thumbs up for the planet also, saving all those controllers and avoiding them to end up in the trash!

[@Mosstachio]

Thrustmaster eswap x pro once the elite goes out due to buttons not registering, double pressing, sticks going out entirely, etc. The eswap allows you to swap modules and has far better quality thumbstick modules available (often times able to set deadlines to 0 and they don't wear out as quickly), not to mention mechanical switches for buttons instead of the mushy rubber contact pads that get 1 speck of dirt and stop functioning correctly

[@Gigachad-hb7ji]

You should have bought hall sensing controllers.

[@EatSleepSkrrt]

Xbox controller are sturdy like Nokia 3310 but the sticks since 360 always drift😪

[@EatSleepSkrrt]

@@Mosstachio yes bumper jitters and both sticks have mad drift you would think after 2 years it would still be fine after paying 250

[@Gigachad-hb7ji]

@@EatSleepSkrrt Just get the gulikit king Kong pro 2 or the 8bitdo ultimate Bluetooth. Hall sticks inside.

[@nathanielgonzales418]

I usually don’t comment on videos but I’m very grateful for him showing us this fix. It was such a pain trying these other fixes but this one worked great for me! No drift at all anymore!

[@Red_dead_Redemption_4_Life]

Does this work for dual shock 4 controllers?

[@chanceclaps4512]

2 years later and with a 3 year old controller and this still works! Thank you!

[@jeremymiller8932]

I am so confused lol. I tried every other fix and I was just about to send my controller back but this video popped up on recommended so I gave it a shot and it works so far! Thank you so much!

[@tomek9192]

Same with me xD I had enough and it was my last hope... I done it today and hope it"ll stay good :)

[@teknosbence2482]

Same with me thanks a lot

[@jakwadd]

Out of interested has it lasted for you guys?

[@EZDoes1t]

@@jakwadd would like to know the same… just fixed mine and it works great. Didn’t know how permanent the solution is but at least it was easy fix!

[@jakwadd]

@@EZDoes1t it didnt last at all for me😂

[@Slothdude0]

This was amazing thanks so much I’ve been looking for a fix for so long and this is exactly what needed to be done to fix my drift.

[@pennypacker808]

Just followed your instructions and fixed BOTH of my Elite 2 controllers in like 5 minutes. You are awesome!!

[@johnposey858]

Hey bro, I have never left a comment on a KZbin video before, but you have compelled me in a way that I can't resist. I am on my 3rd Elite series 2 controller (owned 2 Elite series 1's as well), and it has developed severe stick drift upwards, on the left joystick. It is still under warranty, but I honestly do not want the pain in the rear of shipping it into MS for repair. So I just stumbled upon your video, and it gave me the courage to finally pop this controller open and attempt your quick fix. Let me just say... THANK YOU SO MUCH!!!!. I have no drift any more and I have sat watching the accessories app for over 30 mins and the drift is gone! God bless you my dude, your a legend!

[@jeffisawaffle8084]

Did the drift come back or is this a legit method to fixing it

[@jeffisawaffle8084]

Cuz if it didnt come back they need to tweak their sensors and fix this problem altogether

[@Astr0Pr0j3ct]

Did the drift in your controller come back? Just wondering

[@pizzagateisreal]

Omg dude you've saved me days of gaming and 120 quid. You absolute legend i tried all other options. Thank you so much❤

[@nairb2]

Thank you so much! I was losing my mind opening up my controller and cleaning it, just to find the stick drift was still there. Eventually, I figured it had to do with the sensors. You taught me thisnnesy little trick, and it's working so far :)

[@AFLleader]

Life saver. If you’re doubting this man. Just do it. I was getting super frustrated that my expensive controller wasn’t working. Turns out it was an easy fix. Thank you!

[@sebj7]

Thank you so much! This was such a simple fix, but worked instantly on my elite series 1. I came across your video when looking for ways of fixing my stick drift, as i was weary about spend $180 on an elite series 2 when i have a perfectly fine elite 1, with the exception of slight stick drift, which has now vanished since following your video and again thank you!

[@eddiealaniz6321]

If only there were more tutorials like yours. This is my first comment and man are you freaking awesome. My 8-year-old dropped my first elite and then I went and got the series 2 and dropped this one. I thought he broke it and after searching, I found out it wasn't his fault, but no one had a fix. Well, they did but it was this and that and whatever. Gabriel, THANK YOU. JUST THANK YOU FOR THIS. IT WAS AN INSTANT FIX. However, I could not remove the guards but was still able to pry the sensor. i did not force back on due to fear of breaking it but man, instant fix. I don't know if you all play Fortnite, but almost everything you do, you have to do it standing still. Any movement resets the action, and it was frustrating with my damn character moving forward randomly. There would be times where I was scoped in on someone and then all of a sudden, I can't see through the scope because I'm dead due to falling off the roof or cliff or blimp because of my stupid forward drift! THANK YOU AGIAN!

[@shai5550]

Thank you! It works. Having to go through the trouble, assuming it was dust, realized i had no choice but to open it to see if it really is dust, having to wait and order a special screwdriver to use for the screws, only realizing that it's not dust because it was clean inside when I first opened it (only had it for a 1yr+). Then feeling lost on what else could've cause the joystick from drifting. Literally scraped off the top of that green tab but finally had it slightly open like you showed and it works to my surprise! Saved my money and having to endure that. Hope it holds out well.

[@D0WTA]

best quick tip I have seen for this. Amazing work Gabriel. Thank you. I will be passing this on to people I know. Especially since the same company makes the analog gyros for gaming systems. So you didn't just help us Xbox users out. You may want to change the name of this to "Instant Drift Fix on analog controllers or something." I'll send this to a friend and see if it fixes his ps4 controller. Thanks again.

[@Zirus_Blackheart]

did it fix his ps4 controller?

[@tmw7237]

I watched so many videos with this issue, but no one helped. Your Tip is absolutely magic. It worked and you made my day

[@y2knowledge]

I didn't even bother sending mine in for warranty as the majority of the reviews state that the controller they got back had the same issue or worse (you're sent a refurb, NOT a new controller). Mine is a bit gnarled because I didn't buy the plastic pry tools to open it but oh well my controller works. Awesome video!

[@YoshiBros1389]

The first video that actually fixed my drift, thank you 😭

[@JORGEcodBEAST3]

This worked for me also. Only problem I had was removing the stick cover. I felt like I was going to break it so I just left it on and was able to reach the little sensor without having to take it off. Thank you so much my controller is now fixed and no longer having drifting issues

[@psecomfytv9668]

feel u

[@naxtontv5526]

I jus did exactly this and it worked thank you

[@diizzzz8300]

That’s what I did, I felt like I was gonna break it😂

[@briansledzzz3493]

How did u get to the little sensor without taking off the thing

[@deangelo17]

Can you pls tell me if your controller is still working after doing this fix?

[@Ender018]

Thanks mate you're a bloody life saver! I can't afford a new controller but your trick has completely fixed the drift on my left analog stick. Thanks again! Also just wanted to point out that I didn't have to unscrew the dome of the stick. I simply pushed it towards one direction and it gave me enough space to tweak the green sensor.

[@KennyNiii]

It worked. Look me 10 minutes and adjusted the same sensor you had problems with. Some trial and error but your video covered it all. Thanks!!!

[@headhunter_rg6449]

Thank you so much for that simple trick! You literally saved my controller from getting trashed… I had that problem for more than a year and every problem solving hint was like spending much money, completely remove the sensor or simply didn’t work out for me… hopefully that will last a while ;)

[@davidmartinez9416]

Are you still using the same controller? Or did the issue come back?

[@ardabecanm6177]

OMG it actually worked. Thank you so much dude, you made my day

[@thegothcrusader6246]

I found an elite controller at a thrift store for 10 bucks and it came with the drift issue. I used it for about 2 months before really giving a shot at fixing it and your video was the only video that made complete sense on what to do and it did in fact fix the issue much appreciated

[@joshuapaularroyo9973]

Thank you so much for fixing my controller. I just subscribed to you as an appreciation for this short, but informative video.

[@kanye6537]

the first video that shows the whole process and clearly explains how to fix it, cannot thankyou enough the process was very simple and quite fun to see the inside of a controller

[@jacquelineyee8569]

I had this problem, very infuriating. So thankful you shared this. I had a difficult time opening the faceplate, but with the proper tools, I got it done. I ended up not having to remove the caps and it solved my drift. ABSOLUTELY THANKFUL.

[@blindintuition5131]

What tools did I need for this ? How did u do it without removing the caps

[@Mrdudeluck]

@@blindintuition5131I used a Lego brick separation thing😂

[@blindintuition5131]

@Mrdude luck thanks I really need to fix my bf I got a warebty and lost the stupid thing to show them so guess this is my only option... open heart surgery it is guess I can't fuck it up anymore then it is considering he's using a basic wireless controller oflver this one do to this problem .just was scared of destroying it

[@formerdwellerofthebasements]

Thank you! I had given up on trying to find a fix until you popped up in my recommended. Worked instantly. Thanks a ton! 🍻

[@GoBlueGreg]

Thanks so much for this video! The stick drift on my XBox Series S controller was so annoying but thanks to this video it's GONE! THANK YOU! 🙏

[@edwardkyle8093]

This worked really well and mine was really bad. Fixed it for now thanks

[@FE4R3D]

Worked for me. Hopefully, this fix lasts for quite a while! I followed these steps but also used compressed air to clean the inside of the controller. My analogs were not twisting off, and I didn't want to force them, but I was able to slip in the screwdriver and open up the sensors easily.

[@cxnnoruk8537]

What did u use to pry the controller open. My one has had drift since I got it and it's just getting worse

[@FE4R3D]

@cxnnoruk8537 flathead, slip it in to the frame where the Dpad is and slowly go around popping the frame out.

[@carlos7804]

How did you separate the sensors from the "square"? Were yours green, like in the video? Mine are black and my tweezers bent before I could get them to pop.

[@FE4R3D]

@carlos7804 mine were like the video, unfortunately. I just followed those steps exactly. Try a little flathead screwdriver instead of tweezers.

[@logisoc8061]

Thanks man!From the all repairing methods i ve tried, the best one is yours. You saved me literally 60$.

[@avengertj]

Tried cleaning like all the other videos say to do. Your method is the only one that worked. Thanks man👍

[@Mosstachio]

The green caps have a film of carbon on them. The modules work similar to a brushed electric motor from my understanding. So, over time that carbon film gets worn and doesn't make solid contact. By adjusting the caps like this you're making it run on a different section of carbon film that may not be as worn (but will quickly wear due to it being very close to the worn section). It also can cause loss of contact entirely if you position the caps too far away. This isn't a long term solution, probably best used as a short term solution while waiting for your new controller to arrive (thrustmaster, powera, razer, rig, victrix, possibly even scuf but I wouldn't recommend scuf honestly, pretty much anything other than another elite 2 or other OEM controller that will have issues within months).

[@TheVikingSailor]

Until they star putting HALL sensors or using magnetic POTs this will be a issue we deal with.

[@dannyhernandez3431]

This worked perfectly for me, my stick drift was so bad it’s like I was pressing forward!

[@josich21]

dude, thank you so much!! just fixed mine. just bought it last christmas and the drift was so nasty i was about to cry. but thanks to you sir it was a quick and easy fix. stay happy, safe and blessed buddy!

[@8ZRP8]

Dude thank you so much you’re a legend I recently had to stick drift on both of my joysticks but now since I watched your video you’re literally the best video that I ever watched thank you so much💖

[@J_Mcfly]

THANK YOU BRO.. THIS HELPED ME A LOT

[@mitchellsoto3064]

I was able to apply your fix without unscrewing the joy stick. I pulled it to the side and reached in my driver and did as you did and it worked perfectly

[@simonrise9123]

I did this aswell. because I had no chance at unscrewing it. Neither do I have a heathen that other videos suggested

[@mitchellsoto3064]

@@simonrise9123 yeah mine is on tight lol but the fix however didn't last long for mine, like a month later it was back at it drifting all over the place, so I found another fix! Do the same thing but get a swab and some 91% isopropyl alcohol and rub it between the green latch and wait for it to dry and clip it back on. The drift disappeared completely and still hasn't returned! If you try it, let me know if it works!

[@alexandfriendstheemeraldbo9080]

@@mitchellsoto3064 is that second fix still working

[@mitchellsoto3064]

@@alexandfriendstheemeraldbo9080 I've been playing Apex Legends pretty intensively the past few days and so far there's no sign of it drifting even a bit! I tried this alcohol solution last week so I can update you in a few days if anything changes

[@koraysblog]

@@mitchellsoto3064 would like an update as well :) Just fixed my stick drift this way but I’d like to know if the alcohol can fix it more long term

[@majinmorpheus]

I ordered a replacement on Amazon, then found your video the next day & its worked a charm, now I have 2. Thanx mate!!

[@kgulba]

I cannot believe it that this actually worked with my Razer Wolverine Tournament edition.....absolutely gutted, 65gbp paid for gamepad and started to drift when I pressed the sticks So I left it, tried Hori, Nacon, even xbox one original - all drifted after approx. 3 months of use I did this, tried for 60sec with triggers...worked Played yesterday a couple of fifa matches - no drift at all Thank You. I owe You a 1000 beers man

[@vindictivegrind9370]

I’m thinking of doing this. I’ve been playingCold War Zombies and when I move forward and back, my operator continues to move for a couple centimeters and then either stops himself or I tap the joystick and it corrects itself and stops the extended movement. Usually continues to move when I hit the perk machines

[@darrenhunt7838]

Just discovered your fix. My series 2 had stick drift from new and because I won it in a competition I didn’t have warranty on it so I threw it in the draw and forgot about it. I just followed your instructions and it is now working as it should. Thanks so much for the tip 👍😀

[@Kaiyening]

This video just made me feel so much more secure about the one I just ordered, so thank you!

[@treenugs117]

I tried this off and on with little effect but after spending some time playing with it I seemed to have stopped any drift and it's more precise on small movements. Pulling the sensor cover back and leaving space would sometimes work for a few minutes before issues arise again but it would always get worse, I simply removed the actual sensor piece that sits inside the clip and placed it back in, took some tries to get it in proper place but once I did the drift is very minimal to completely gone and after a full gaming session I can confidently say it's much improved. I'm sure it'll get worse after using it more but it's already been a day of use without the drift after placing the sensor back in vs 5 minutes of play without doing that

[@smokeinc.7715]

Could have saved me countless hours and dollars...thanks buddy

[@deandrecarson4374]

Brooooo you really just fixed my controller. Thanks. I’m posting this everywhere cause this needs to be broadcasted on Every known media platform.

[@vis-exile]

i'm finally able to use my XB1E controller again after so many years! It was my favorite and i was sad having to shelve it, but now it's back and I'm So happy! Thanks for showing this fix!

[@JustinTessier]

Great fix!! For those who are having a hard time removing the thumb stick covers, you don't have to. Just move it aside to access the actuator.

[@mogwipe734]

Thanks lol

[@mrbigtymer78]

Yep that's exactly what I did as well

[@itsea]

I’ve been suffering from drift for nearly a year now and have opted to not use my elite controller. Thanks to this video I finally fixed my issue and can actually use this so called “elite” controller as it should be. Thanks so much!

[@landon974]

thats awesome, these things are so expensive just for them to get drift in like 6 months or out of the box

[@markgallie7899]

Tried so many other fixes from other videos, moved the blue right cap over, blew it and cleaned it abit then put it back same problem, left it out like you said, instant fix. THANK YOU

[@HmmChunkyLizard]

Bro this worked for me! My left stick got the forward drift after 3 weeks of owning the controller. Never came across your vid when I was looking for a solution, as It happened before you made this vid. So it's been a long time since I used the controller. My new spectra controller I bought to replace my series 2 broke last night. Right bumper to be exact. After only having it for 2 months. I'm not even rough with my shit. lol. But anyway, I didn't have the money to buy another controller, so figured I would try and fix my series 2 again. That's when I came by your video and now I got my favorite controller back working! it was definitely a pain in the ass to get the face plate off. There are a few scratches and dings because of it ( didn't really have the proper tools.), but I'm just happy it works again! Thanks so much man!

[@kiwaycanny6522]

You can also fix the rb lb issue by spraying wd-40 onto the motherboard Button

[@jm75uk]

Thanks for the tutorial, saved me buying a new controller Just a heads up for people struggling to get the thumbsticks screwed off like me, you can still get into the sensors with them still in place, if you just pull the thumstick to the side you'll get into the sensor with your screwdriver

[@jeffphilp7430]

Simple, short and concise video. Mine has exactly this problem but is still under warranty so microsoft are happy to repair or replace it, but next time when it happens I shall be following this excellent guide. Thank you.

[@addidaswguy]

Wouldn't everyone's be under warranty through Microsoft? Or how long is it?

[@jeffphilp7430]

@@addidaswguy I think the warranty period is a minimum 12 months, you can see the exact details in your microsoft account as long as you have registered your device.

[@MartimNascimento]

So you can’t do this “trick” when the controller is on the warranty, right? like if you ever need to replace it they might see you touched to controller components or something? I have that question if anybody can help

[@johnturkalj2994]

Thank you for this man. Saved me a lot of money. So quick and easy. Great video 💯

[@abudabislol]

THANKS MAN! My warranty ended 2 weeks ago. Yesterday when my elden ring journey was on the move analog drift occured. Cleaning it and other tips didnt help. After making that gap it works great! Thanks again!

[@aj3117]

wow this acc works on my elite V1 thanks so much dude

[@jessenelson9768]

Does removing the plate void the warranty? I’m about to send mine off since I bought it in October, but previously I owned the series 1 and repaired it myself multiple times since it was out of warranty. Removing the screws on the series 1 voided warranty, so I was curious if it does for series 2 since there are no screws.

[@Jxyelan]

How do you get to send it off the steps are so unclear

[@jessenelson9768]

@@Jxyelan it’s very simple, as long as you have transportation to your local UPS. Log in to your Microsoft account, enter your serial number on the back of your controller, and this will tell you if your device is still covered under the warranty. If so, you’ll select to start a service request, and provide your issue as well as your mailing address. Within 24 hours of completing this, you will receive a return shipping label. You can either print it out, or just ask the UPS people if they can print it out for you. At the UPS location, they will box up your controller for you, and then from there you wait for your replacement. I haven’t sent mine off yet, but I will be in the next few days. I already have the label printed, I just need to go to UPS. The majority of this was explained in the video, and the process is no different. The only bit of info left out was HOW you send it back.. You simply just take your controller to a UPS location, and they will handle it from there. (important: KEEP ALL OF THE REMOVABLE PARTS/CABLES/CASE as they are not required to send you a new box like they did in the video) I hope this helps. Have a wonderful day!

[@J_Mcfly]

YOU AINT GOTTA TELL THEM SHIT.. THIS FUCKERS MAKE SHIT CONTROLLERS AND ARE OVER PRICED,, YOU DO WHAT YOU GOTTA DO.. IF YOU CANT FIX IT THEN SEND THAT SHIT AND DONT TELL THEM YOU TRIED TO FIX IT LOL..

[@sahgahndeezbahls1536]

@@J_Mcfly there’s a sticker on the controller labeled “warranty” ass hat. And to open the control you have to break it. Now stop talking

[@jessenelson9768]

Sent my series 2 back and got the replacement in 6 days. And to answer my own question, dont try to fix it yourself if it’s under warranty. I fixed my series 1 multiple times, but I was just curious about their handling of the controllers that people tried to fix before the extension occurred.

[@kristofviola855]

Thanks so much! The left joystick on my basic Series S controller was drifting slightly, although it wasn't nearly as bad as yours it was annoying. I tried your fix after unsuccessfully trying other tips and it worked 100%!

[@Dzcrr]

I dont comment too much on YT but u deserve a thank you man. Ive been dealing with stick drift for some time now and at first i just opened the controller and cleaned it which was fine at first but then it just stopped beeing an afficient method. But u saved me so much money, time and u made R6 fun again for me. Thank you for this tip. P.S How often does the drift come back??

[@txsaltyangler7093]

Why wasn’t this the first video clicked on!? Bro thank you!

[@wailhussein6453]

You’re awesome bro. Fixed it instantly after giving up with all the other vids. Much appreciated 💯

[@adamrice5906]

I have only comment on like 3 videos in about 10 years of watching youtube. This fix worked thank you subscribed saved me 50 pounds. was about to send off tomorrow, after looking at other KZbinrs and fixes not working. 👍👍😁

[@josephborden1257]

Thank you so much. I love this controller and have been rebuilding it. I got a donor controller for parts but the forward and backwards drift was driving me crazy, because of your video it's fixed. I sadly snapped the shaft trying to unscrew the collar on the right thumb stick when I was disassembling the whole controller. I'm pretty sure they used lock tight on it.

[@benjaminansin1182]

Thank you so much for this! This did the trick. Good as new. I really wasn't looking forward to buying a new expensive controller.

[@Colts63AK]

THANK YOU! I have had my Xbox Series X for not 2 months and my controller already got stick drift. I just tried this and it worked 🙌🏻

[@ZeljkoTerzic]

Thank you! This is by far the simplest method I found on youtube. Fixed drifting issues :)

[@XLucero1]

Fixed the Magnetic Tension issue with the metal stick attachment as well. Wow, you deserve a vacation. I was able to fit screw driver in there without unthreading the cover.

[@thomasphillips3072]

This is INCREDIBLE to say the lease, I just gotten Dragon's Dogma 2 for the Xbox Series X and all my character can do is constantly walk on it own up or down and talking and picking up things were virtually IMPOSSIBLE!! I tried all kinds of cleaning methods and NOTHING worked!! wasn't about to waste time and money on a new controller for $60+ I tried your trick and it worked!! I can't believe this simple tactic really worked. Than you guy for everything now I can enjoy my games.

[@wesleybridget3024]

Mans a legit wizard, this does indeed work, thank you for the 10month old video!!

[@Light-bd7so]

This works on SCUF controllers too. I had been having terrible drift for about a month and I tried this and it works like a charm. Thank you!!

[@yal100]

This is amazing. Not sure if you were the first to come up with this, but duuuude! I have 3 controllers and 2 had skyward drift on the right stick, really frustrating. Tried, alcohol, cleaning, air, EVERYTHING! Nothing! BUT this worked instantly.....FYI my sticks just pop off straight up no unscrewing. Also please add Xbox One and S controller to your title so more poor souls find this video. You're a life saver man!

[@jamesghbray]

I was sceptical - but this completely fixed the up/down drift I was having on the right stick! Thanks so much!

[@benlanglois6786]

I'M TELLING EVERYONE ABOUT THIS!!!! so many videos but this one is IT!!!!!! thank you for this info, saved me from buying a new one for no reason and now I can enjoy my $200 controller again

[@ljayttv]

bro thank you so much I just bought a scuff 2 months ago and I really like it and I thought I would need a new controller but I don’t because of you.

[@al_wax]

Bro you are a god amongst men. Thank you so much and hope you have a great 2024!

[@NeoJ4K3]

This worked and helped me so much! i was about to through my controller out the window in frustration of drift lol. Thank you so much!

[@lazrickblackburn5824]

Thank you so much for this video i just bought my elite 2 last month then I noticed there was stick drift coming it but after this video it gave me the motivation to it my self now my controller is back to normal💯💯

[@jimdillman3295]

I had major drift on my 2 month old Elite Series 2. This solved the problem instantly. I did need to adjust the gap back and forth to find the sweet spot, but once I hit it no drift. Thank you!

[@isaiahcolwell5061]

THANK YOU so much. You just saved me so much money, this is a great fix. Hopefully it last a little longer

[@clappington9438]

cant believe that worked. elite controller has been in a drawer over a year and this video popped up on my feed figure wth might as well. Thanks!

[@lixmitchell]

omfg much love... thought it was too good to be true but wowowo instant fix as promised! saved me $200 take my upvote and subscribe and all my love!

[@zac3737]

Figured I’d try and fix one of my broken controllers myself as a last-ditch effort, after watching this I fixed both of them 😂 I appreciate it 🤞

[@vfcdogg9470]

duuuuuuude so glad I found your KZbin video let me tell you, it is not easy to pry the face of the controller off. definitely grab some plastic pry tools so you don't damage your controller. getting off the face cover on the joy stick was a lot easier than the face cover of the controller. you need to use a wrench and turn it as center as it sits on the controller itself. def thankful for your video. was just about ready to buy a new elite controller

[@raees3562]

This worked! You're the goat fr fr. Out of warranty, so saved me 100$ sending it back to microsoft to fix. Also, I didn't unscrew the analogs, I just moved it to the left and had enough space to get to the sensors with a pair of tweezers.

[@gabrielvaz2461]

Glad I could help

[@akihisaisback7437]

MY MAN YOU'RE SUCH A LEGEND! I was almost thinking to throw my controller away. Thank you.

[@messiahmvp]

Thanks for your vid man! I almost threw mine a away or sold for cheap had I not came across my vid. Followed exact directions and it fixed my stick drift

[@АртёмХТЗ]

Thanks a lot! Already thinking about buying a new gamepad. People say that this method does not help for a long time, but let's hope for the best.

[@zombinic]

I never comment on videos, I freaking love you!!! Thank you so much!!

[@iviur5627]

DUDE THANKS! i tried all these different methods and this is the only one that worked! you da man

[@Its_DragonC]

We made it to 2024 and this video still helps. Have two current elite controllers and they both started having issues. First one I have for a little over a year, decided to fix it and stumbled across this video. Now instead of unscrewing the dome all I did is push to the side so I could access the green plate, then with some tweezers I managed to unhook it and hook it back together while still leaving that little gap.

[@gabrielvaz2461]

Im glad its still works! Thanks for the comment!

[@Bazooka970]

Thanks, I really like how you got straight to the point.

[@redandblue7229]

Thank You so much bro. I thought I was going to have to buy another scuf controller. You actually saved the day!

[@escobark6956]

Broo thank u so much I bought a e swap pro and after few months that happend and I couldn’t find ministicks in my country I thought I wasted 150$ until I tried this thank u broski u made my week

[@ThatGuyWhoComments1]

Holy crap it worked! I was trying to use alcohol and a duster and none worked. Good it's such a simple fix compared to the other crappy stuff that the series controllers have like soldering etc that I had to do because mcsft cheaped out on parts. Man has it been a big maintenance journey with the series controller, just one thing after another like a car lol. Thank you.

[@Xenot84]

Dude you're a life saver. Bit of advice for anyone trying this, you don't even have to get the joystick cover off by unscrewing it. Just move the joystick away from the potentiometer in question and pry it off with a flat head. Easy fix, took me 5 minutes first try.

[@izzyk9267]

I cant tell you how many times i pulled my control apart I’ve literally tried every hack on you tube besides soldering and this one worked for me so thank you👌

[@horsiedonk]

After taking apart my controller about 5 times, cleaning the joystick thoroughly, and playing with all the hardware near the joystick, I hadn’t found a solution till this video. Amazing tutorial👍

[@GOATGamerProSticks]

Intresting fix reduced pressure in the worn contact track, im thinking on the inner wiper radial the little buggers always turn into shovel gouges when the peaks wear off. All they need is better quality wipers & contact tracks. Possible BAM coating might work wonders hard material & reduced friction other than cleaning then spraying with GT 85 PTFE lube? Im trying to put together you tube info on Potentiometers & Analog stick size form factor, if you get it all right with decent calibration options response curve & dead spot the jack of all trades pad eclipses M&KB. Height ranges in the 0.05mm increments truely compliments dialing in the muscle memory. Paired with shaft width selection provides total mechanical control comfort. Way beyond kontrolfreeks or X Box magnetic stick line. Im gunning for poorly optimised games companies on minimum viable product BS oversight. Third party endorsement reliance is a lazy pyramid scheme.

[@horsiedonk]

@@GOATGamerProSticks You sir are speaking another language, but I agree

[@GOATGamerProSticks]

@its neat Yep, but i can fix confusion you will be fully up to geek in no time flat lol. Enjoy the playlist of all the control pad knowledge you will ever need. I started with maintenance interests myself then fully redesigned my own modular stick platform. kzbin.info/www/bejne/rILIpJp3qddlm5Y Search: BAM metal Its interesting stuff 3rd hardest material under diamonds last i checked & one of the least frictional materials known to man. Its probably super expensive to produce as a solid but coatings who knows?

[@lurch26killa]

I am commenting because this actually works!! I was holding on to a busted stick for a year. This is the fix. Thank you, thank you. 2 years later!!

[@juliosanchez933]

Oh my god this worked!! 🙏🏼 I was just thinking about buying a new one now I don’t have to 🙌 you are the best man!!