iPhone 6 Complete Tear Down and Rebuild with Custom Housing

[@interestingspagetti]

I did it!!!!!!! First go. I had no probs with the little metal disc's that went in volume buttons. There was a small metal plate that need to be fitted after installing camera that had no mention in your video. But thank you "Go cell phone repair". I could never have done without you. Have learnt so much during the process. Took me 3 hours. But thoroughly enjoyed!

[@GoCellPhoneRepair]

Thanks and congrats! You must have a lot of patience and persistence.

[@interestingspagetti]

I've just got a 6s that back cover doesn't look great. So will be doing that too. Will have a look through your vid's and see if you have done one of them. Great content btw.

[@quinelder8581]

Watched whole vid, was very thorough and I'm glad I watched it. I completed the whole iPhone in about three hours and you were very clear about what to do. Thank you

[@babneetd7282]

Just followed this tutorial to the tee and replaced my housing thanks to you. Your method for organizing the removed screws was a life saver. Had issues with removing two screws that ended up being stripped but that was due to the crappy screw driver I had. Thanks again for taking the time to make this tutorial don't stop doing what your doing people out there like me need your videos!

[@GoCellPhoneRepair]

Thank you. Will do.

[@therealist2000]

I also plan to follow this tutorial, Mike I found some foam cushions on eBay (goo.gl/WVLCWr), should I buy one?

[@GoCellPhoneRepair]

That's actually not a bad idea. You won't need 10 of course but I guess they don't sell smaller quantity.

[@margareto7832]

I watched this video all thru; you have a very relaxing mellow toned voice, so thank you for all the info on this tear down!

[@novhatv]

Thank you so much I was nervous I would have to replace my iPhone charger I clean it out with toothpick and what you recommended and now my iPhone is charging again

[@stephenramnarine7396]

Watched the vid about 4times getting ready to do this in a few days

[@interestingspagetti]

I'm 30 mins in. Wish me luck

[@KevDoy]

Dave Hammerton how did it go?

[@EastDallasKicks]

Stephen Ramnarine how'd it go

[@EastDallasKicks]

Dave Hammerton how'd it go

[@seabass7906]

great tutorial, got done swapping an iphone 6 housing a few minutes ago and it was a success thanks

[@prosteairlinesrblx8269]

This was very helpful! Thanks so much for explaining everything so carefully. I change my iPhone 6 into the looks of and 8! Its works better than before! I couldn't of done it without you, again, this was so very helpful.

[@SynetProductions]

where did you get the iphone 8 housing for an iphone 6?

[@phillyaccord5635]

Was it hard

[@tilak9253]

SynetProductions search for one on ALIEXPRESS

[@Sim7NYY]

I like the narration too and I appreciate the effort you put forth here. A++

[@GoCellPhoneRepair]

Thanks. I'm impressed by anyone who gets through this.

[@nathanlewis7916]

lol i watched this entire vid just for entertainment i dont even have an iphonem6 but i plan on doing this one day. his voice is so soothing lmao

[@GerardoNazir]

Your Tutorial is awesome! and, I like to watch what goes on in real time, the real things that you encounter along the way. Thank you, well narrate it and nice voice also!

[@michio2k5]

Awesome video! Very helpful. I have a issue.. I have to unplug the Batterie for a Short Time to Start um the iPhone.. So you have Army idea to fix it?

[@piksvideo]

Great tutorial, as stated in the commentary worth watching before you start the tear down, worth magnatizing your screwdrivers as this saves so much time in locating the screws.

[@docminty2882]

I put the same housing on my 6s and it turned out great. But putting a green one on my 6. I lost the little metal dot for the volume button. Where can I get a replacement? Thanks

[@vincentcorleone4951]

bro can you recommend me a screw chart some screw card which show which screw belongs where for i phone 6s plus?. i will change back housing. but im afraid to forget where to use right screws and confuse them all.

[@Victor-by1um]

best in the business by far ..watch the whole video, step by step its fantastic thanks again!!!

[@GoCellPhoneRepair]

Thank you.

[@madern7]

This was really interesting to me and I plan on doing this soon so I watched the full vid prob going to watch it again

[@dch1648]

Great tutorial, replaced back housing pretty easily though I did end up with an extra bracket.

[@Ismail-dj5cg]

thanks for the video, after finishing my screen is but isn't siting down. what do you recommended i try ?

[@gulic15]

you are my hero. it took me 5 hours to complete but i did it :) thanks

[@AjithKumar-xw5lu]

Great video 👍🏻very useful now am gonna change housing myself. Do I have to take back up my files before changing it ??

[@GoCellPhoneRepair]

Technically no since this should not affect stored data in any way. That said it's always a good idea to make backups on a regular basis. You just never know.

[@burneracc1950]

Awesome Video! I have one problem: I replaced the normal housing with one of the "iPhone 6 like iPhone 7" Housings and after i completed it everything worked fine but then i realised that my camera doesn't focus anymore.. Do you have an idea why and how to fix it?

[@demolgi97]

Thank you for the video , now I have the same backhousing as you but I have a question , is it normal that the vibration so loud is of did I something wrong?

[@GoCellPhoneRepair]

Maybe the motor wasn't screwed down all of the way? Hard to say for sure.

[@MultiChadmiller]

Whats the cable on the right side of the camera you removed at 21:21 mines missing and i thunk its effecting my signal constantly at 2bars and thats the only thing im missing on my phone after i changed the back. please help!

[@GoCellPhoneRepair]

Could be part of the antenna system but sometimes these housings can affect your signal. Any idea where it went?

[@ShoePac77]

HI, great video! But one little problem, you may help me with... I´ve been doing smartphones repairs and changing to the custom housing for a years, but until now never had issue with rear camera focusing after changing to the custom housing... I am pretty much sure that I´ ve done everything just fine, camera is working but it just wont focus which leads to poor quality of images ofc... I´ve tried with af lock (long tapping) but did not help... Also I did notice that the metal holder which came built in the custom housing on the place where rear camera comes, is a little bitte different then original one (yours also, mine is same as yours), original one has a tiny teeth on two sides of the circle edge of the metal holder... so I was wondering maybe is in that problem, maybe those teeth are giving the ability to focus the camera... also I just moved the camera from original housing to the custom, there are little chances to break it during that time... any suggestions what might cause the problem? I´ ll try to buy a new rear camera and replace it, but I do not believe it would help...

[@GoCellPhoneRepair]

Is it possible to use the original lens? It could be the teeth you are referring to or maybe the lens on the new housing is causing the problem. Haven't run into that myself yet.

[@overknight5278]

I have an iPhone 7, and i have an old iphone 6 and im deciding to mod it, to match the matte black 7, i orderd a glowing apple logo for the 6 so i can attempt to do it if its a success ill do it on my 7 (just the glowing apple logo) and i got the same housing, i just didnt swap the gold and silver pices… i kept the silver

[@agbennett1]

Thanks for the video! Quick question, how long does it take if I want to just disassemble the phone? Thank you!

[@GoCellPhoneRepair]

It really depends on your experience level. If you are doing a full disassembly including all small parts I'd give yourself at least an hour the first time. Once you've done a couple probably cut that time in half or less.

[@lucasdj25]

For anyone trying this, you do not need to purchase the stand-off screwdriver if you don’t own one. A flathead works fine. Also for the little metal circle on the volume buttons, a little bit of superglue will hold it in and not affect the functionality

[@Sesar707]

Awsome video mike, you have a apple glow kit for 6plus?

[@GoCellPhoneRepair]

Thanks. Not on hand but I can order them. What color are you looking for? It takes about 3-4 weeks to get here from China. Maybe longer due to the holidays.

[@Sesar707]

Go Cell Phone Repair looking for a white one, and i know holidays make things get here longer

[@GoCellPhoneRepair]

Ordered. Should be here by this date next month.

[@Sesar707]

Go Cell Phone Repair thanks mike

[@CTC2002]

Watched this through 3 times now in preparation to put an iPhone 7 style housing on my iPhone 6... I take it that you can swap the lightning port/headphone jack assembly and speaker over to the new housing before tackling the logic board to make screw organisation simpler.

[@GoCellPhoneRepair]

Yep. You can do the lower flex and speaker independently of the logic board.

[@CTC2002]

I shall do that then, my replacement housing arrived today and appears more barebones than yours was, the metal retaining bracket the camera clips into isn't present on mine, so I've had to order one as I've heard that this bracket is welded in on the original housing and removal is destructive.

[@CTC2002]

Go Cell Phone Repair just done my housing replacement today and am pleased to say that it was successful. Unfortunately the external camera lens on my housing replacement was misaligned meaning photos taken are now blurry and obscured but everything else works as normal. My camera foam even came out of the old housing intact and in one piece! Thanks so much for making this video as I would not have been able to do this job without it.

[@GoCellPhoneRepair]

Congrats! Are you able to solve the camera problem maybe by realigning or replacing the lens?

[@CTC2002]

Go Cell Phone Repair unfortunately not, the physical cutout on the housing is too low. I was able to get it near enough aligned, but when I put the logic board back in and plugged the camera into it, the camera shifted back up. I will go back in at some point to rule out trapped dust though.

[@zenithdawg1695]

thanks for share video on youtube, now i can housing my iphone 6 to iphone 7 custom cashing .. dude i really thankyou

[@maleikcruickshank2282]

I want this for my 6 plus how can I go about it?

[@GoCellPhoneRepair]

Similar procedure. If I get one here I will make a video for that.

[@oreosauce5776]

*Front and back camera, and flash aren’t working anymore?*

[@TA-elliott-wave-count]

I want to make my iphone 6 but what is main thing I need to buy body . logic board, lcd screen and battary , what I should buy next ,

[@midnightsconfide3683]

headphone jack charger assembly WiFi and cellular antennas volume buttons power button home button and all of the coordinating screws to hold everything in place.

[@austinnguyenquan]

Thanks for your video, it's helpful for me

[@wakefieldyorkshire]

This video is a life saver. Thumbs up and subscribed. Many Thanks.

[@SahilSingh-uf1sz]

Hey buddy I am not a professional and doing it first time so can I do this task properly?

[@GoCellPhoneRepair]

It would be helpful to have experience but otherwise it really depends on the person. If you've ever done scale model building that's about the closest thing that I can think of off the top of my head. If you have any doubts though I'd leave it to a pro. Attention to detail, organization, and following instructions to the letter is half the battle. The other is being able to work with very small parts.

[@SahilSingh-uf1sz]

Go Cell Phone Repair thanks for the advice bro

[@docminty2882]

How crucial is the screw location? ( I obviously understand if the long screw won’t go in don’t force it), but I put certain parts with the accommodated screws in little containers for each piece I took out, so they’re all kept together, but I mismatched the screws, help?

[@GoCellPhoneRepair]

Some are more crucial than others but you really want to keep them organized from the start. One area that can cause serious problems is the screws that hold the panel behind the display connectors in place. Ifixit has a chart on this page that you may find helpful www.ifixit.com/Answers/View/221126/Screw+size+guide+or+chart

[@DariusDDM]

Is AAA quality ? If yes did you have problems with this housing like signal drops or bending after a drop ?

[@GoCellPhoneRepair]

Slight drop in signal strength but not enough to make a difference in the areas where I use my phone. Haven't dropped it but most likely it's the same as the original iPhone 6 housing= WEAK.

[@DariusDDM]

Go Cell Phone Repair Thank you very much :)

[@mathiasmoormusic]

Hello, where I can buy same black/gold housing ?

[@GoCellPhoneRepair]

The vendor that I bought this from seems to have disappeared. You can look on Aliexpress but I can't seem to find exactly the same one.

[@pranaygawde4793]

Plz tell me sir...where to buy this housing...🤧

[@GoCellPhoneRepair]

The vendor that I bought this from has removed their listing fro some reason. You might want to check here ebay.to/2gaE58k Hopefully it is similar quality.

[@gabbymalvin7810]

I bought mine on DHgate

[@aronblack9024]

hello can i put iphone 6 plus motherboard to iphone 6s plus housing its the same or not thanks for your answer

[@GoCellPhoneRepair]

No they are different and not compatible. Also, I have ordered two 6S Plus housings and both of them were not manufactured correctly so it was impossible to use them. I'm still looking for a good supplier so that I can do a conversion on a 6S Plus.

[@aronblack9024]

Go Cell Phone Repair thanks man very useful tips because i orderd back housing for iphone 6s plus back housing like 8 plus from china

[@jessicaburm4713]

I have a question, when i tried to unscrew the screw from the speaker the screwdriver broke the screw and now I do not get it out there is something I can do?

[@GoCellPhoneRepair]

It's never easy but happens often enough that I've compiled a few possible solutions here: gocellphonerepair.com/removing-stripped-screws/

[@islamcoherencepertinence.7226]

Be careful, when you change the housing, sometimes you loose the wifi signal, or the network signal is low. You have to scratch the screw on the new housing to have a better signal. Thank you for the video.

[@Obs-dk9mx]

You should connect the battery after the screen so you don't have the chance of shorting out the back light circuit. wich will blow the chips on the mother board

[@mohamudyahya5409]

Great teacher😊❤, thanks.

[@maylinnr]

The pictures from the ebay offer from the description do not contain the apple logo. Are you sure that they will come with a logo?

[@GoCellPhoneRepair]

You should ask the seller about that. The one that I bought did but that listing is gone now.

[@jamescarterthomasburdick72]

i have a 6plus model a1522 that im trying to replace but i cant find the same model any help?

[@GoCellPhoneRepair]

As far as the housing is concerned an iPhone 6 is an iPhone 6 regardless of the model number. Model numbers only vary due to network variations.

[@jamescarterthomasburdick72]

Thanks

[@m.rezaramadhani1609]

i changed my iphone 6 housing with red iphone 7 housing, its look fantastic, but i have a minor problem, the camera wont focus, i dont know why, many thanks

[@GoCellPhoneRepair]

I would suspect the lens. If it's not clean the camera might think you are trying to focus on the lens itself. Try another camera app and see if it does the same thing.

[@m.rezaramadhani1609]

i already fix the rear camera problem, but now my front camera is stop working entirely, :( i guess sacrifice has to be made haha... thanks a lot btw for answering my question

[@MartinFixes]

I think you might have forgotten to put the link in the description

[@danishdadani9810]

Phewww I’m done final result awesome Thank u Very helpful video

[@GoCellPhoneRepair]

Awesome! Thank you.

[@ontoxicated8544]

Followed everything accordingly but phone wont turn on. Possible problem?

[@GoCellPhoneRepair]

Really hard to say. Have you tried plugging in the charger to see if that boots the phone up?

[@moneymikefinancialshow2347]

This video helped me so much... THANK YOU!!

[@jahmeregarnes5755]

kidbatman789

[@scottm9502]

I ordered this and it's coming in a week but I have a question, I have a gold iPhone 6 so it has a white front. Is it possible to make that black as well or will I need to get someone who can do a paint job on the front. Thank you for your time

[@GoCellPhoneRepair]

You would have to replace the screen. Otherwise maybe just add a black tempered glass to the front.

[@user-lj4zw1rv9i]

KB gamingtime You can, but the home button has to stay white so put like a sticker or something along those lines on it

[@monkeyman8265]

Rick and Morty Amazon actually sells full edge to edge glass screen protectors that come with black or white bezels. So you could change the front to Black that way. The only problem is you won’t be able to change the home button without having it done by Apple so it is calibrated other wise if you replaced a home button on a Touch ID capable phone it could brick it.

[@Dante-V06]

Friend you have for iPhone 6s Plus

[@UmarKhan-ov3hl]

Where can i get the template for the screws?

[@GoCellPhoneRepair]

ebay.to/2xnXIiK

[@m4rku53]

you can get a template to hold the screws called iscrews or can buy off ebay

[@superstarphones7938]

Thank you. Excellent Tutorial.

[@user-lj4zw1rv9i]

3:54 if your phone has Touch ID if it hasn't been opened before, don't pull all the way or you will snap your Touch ID cable

[@HenryTheBoilermaker3rdYear]

CAn you do this with the iPhone 7 plus please

[@GoCellPhoneRepair]

If I come across one. Right now I'm using a 7 and when I get a new Android I'll use it for customization.

[@R6t79]

I tried it and now my Audio Jack doesn't work anymore. I also replaced the Lightning flex cable without success. Does anyone have a solution?

[@gustavoriveros7798]

R6t79 did you solved it?

[@fffth5895]

It's the same if I have iPhone 6s???

[@GoCellPhoneRepair]

Similar but different and parts are not compatible. If I get a 6S that needs a new housing I'll make a video for that.

[@fffth5895]

Go Cell Phone Repair I buy a housing for iPhone 6s rose gold.Can you pls make the video soon I must change it because the back cover I have now broke

[@fffth5895]

Go Cell Phone Repair but if I follow your steps can I change the back cover ?

[@HANDSWORTHMAGIC]

You sone exactly what i would’ve done when it came to that blasted foam round the camera lol

[@jacobcolantonio3724]

Hey i did this on an iPhone 6 plus, anyone had an issue with touch ID not detecting your finger. Touch id is working cause i'm not getting a message saying touch id isn't available it just won't let me register a new finger. Thanks

[@christiangonzalez3894]

Jacob Colantonio you have to use the original button from the original screen

[@repairtech09]

Thanks for the video. :) Hopefully the one for iPhone 6s is still coming? 🙏

[@GoCellPhoneRepair]

No problem and yes for the 6S but it will probably be a few weeks.

[@repairtech09]

Go Cell Phone Repair thank you! 🙌😊And no worries. Lol. I'll still be sure to watch it because Iv searched for a fully detailed video to do the conversion on my 6s and no one has had one. Hopefully in the future you could do iPhone 6s Plus also so I could do a conversion on that as well? If that's not too much to ask. Lol.

[@thepvppanda]

Go Cell Phone Repair did you ever choose a glow color cause I plan on doing something similar and would like to see how yours turned out

[@GoCellPhoneRepair]

I didn't. Someone wanted to buy it and liked the gold apple. Next time I come across one I will put the glowing logo in it.

[@shahsolutions2727]

I am from india and i didnt get this housing😒 Is there anyone who can help me? Actually i need iphone7 style housing for iphone 6.

[@belowmars]

but the back casing you replaced will not have the correct imei printed

[@GoCellPhoneRepair]

True. This will not affect the phones performance though and the IMEI can still be found in the settings screen.

[@belowmars]

Am I able to buy original non-printed back housing and laser print everything original? My back housing is dinged up, I am trying to find a way to make everything perfectly original again before I put away my iphone 6+, I am a perfectionist like that.. my phones are almost always perfect when I put them away for collection...

[@THISACOUNTWASTAKENFROMME]

Plan on doing this to my phone my last phone got stolen so they only had pink in stock to replace it wish me luck and cosmic vid \\m//,, !

[@MrSUPERDOPEE]

ALEX TOMPKINS dont do it

[@GoCellPhoneRepair]

Good luck.

[@riccardobaiocchi5188]

come posso svitare una vite spanata?

[@GoCellPhoneRepair]

It's not easy but here's what I know gocellphonerepair.com/removing-stripped-screws/

[@iamthegamer7946]

Works perfect thanks

[@chrisliddiard725]

A word of caution. Apple has taken to having their screws of differing lengths. Meaning if you put a longer screw in shorter hole, it will damage the circuit on the end of that screw. Hopefully the 'right to repair' campaign will outlaw practices of this kind aimed and preventing you from doing minor repairs.

[@nerminokanovic4269]

WTF!!! I ended up with 4 extra screws!! Now what..

[@jodlovaciokurka8971]

:DDDDDDDDDDDD

[@seninalikp431]

Always

[@washx2k755]

@@seninalikp431 ??

[@xoxsparklesxox4372]

Can I have them lost 3 lol

[@ibrahimkholil2695]

thanks! your views sestem is good

[@likhatemin9687]

Did this and my loud speaker isn’t working and also the volume as well as the power button is too lose ! Lost my down volume button! If you want your iPhone to be compact don’t do this.i recommend but the phone looks awesome :)

[@amarg7657]

Likha Temin I’m pretty sure u just weren’t careful I did this and it’s just fine

[@TheFunkytrapper]

///////////that was pure skill

[@mackeljorge1134]

thanks for this video

[@mrjhonathan9880]

thanks for the sharing may god help me lol i'll do it today

[@sharjeelbabur8950]

i i ask u somthing my i phone 6 not open only apple logo show but not open now me charger my phone then only battery show red not charge what problem my phone pls sent me your whatapps im sent u my i phone video pleass help then tell me what problem my phone

[@GoCellPhoneRepair]

Could be a lot of things. I would start with testing the charge port and battery. If that doesn't resolve the issue then you might have a problem with the Tristar IC which is very common if the phone has been charged with an inexpensive after market charger. Beyond that another part of the charging system possibly. Hard to tell without more diagnostic info.

[@sabyasachimondal6471]

i love this vid

[@M235i.H]

Same for iPhone 6 Plus?

[@GoCellPhoneRepair]

Pretty much the same. If I come across one I'll make another video.

[@madern7]

HC I know you’re comment is old but ... it depends on the shop. Apple isn’t going to do it for you for sure

[@applestuf5569]

I don't know what to do

[@abigailterrazas2493]

Thanks

[@applestuf5569]

Everything else is working except for the speaker

[@GoCellPhoneRepair]

You might have bent the metal tabs that make contact with the flex cable or possibly damaged the cable itself. That's where I'd look first.

[@applestuf5569]

Go Cell Phone Repair, Yes I checked where the the cable connects to the speaker it is a little bit torn. So yesterday I ordered a new flex cable. Thanks for the video and comment.

[@bmxgabe]

lamo am i the only one that noticed that dope ass ring??

[@NICOLA9489]

Devi fare un corso di orologeria, ma come si fa a maneggiare pezzi micro con le mani!!!!, devi imparare a lavorare con le pinzette come gli orologiai.

[@ChazizMTA]

1:03:03 lmao

[@mukeshgupta1980]

Worst phone iphone