IPHONE 6 Dead Fix By Changing PM IC

[@JessaJones]

This phone was for training video only, no? The phone has a short on VCC_MAIN because C5202_RF is bad--look at burn marks. It didn't need PMIC change. So many phones are ruined by people who follow and just think "no power = I should change PMIC" Still love your skills, thanks for sharing :)

[@astroman5923]

+iPad Rehab Probably checked the voltage out Jessa direct from pmic is bad for cpu gpu etc and the input voltage is fine indicating faulty pmic I did spot water damage at pmu desense cap C5203_RF I doubt he would change the pmic without good reason unless he's just showing off lol.

[@VoiceSriLanka]

I don''t think he is a showing off type. Check out his other videos. The main thing is he doesn't even use high end tools like Jessa. I am not trying to put Jessa But this guy is really inspiring.

[@astroman5923]

That was sarcasm he's highly skilled. i personally use thermo couples for everything take no risks, this guy has a feel for it you can see him prodding components to make sure the board has reached temp efficient technique it's like art and his timing is perfect. .

[@VoiceSriLanka]

Yea very true.

[@TonyToneFixMyPhone]

Hi Jessa ! I was actually looking for that Chinese dudes video to see his diode measurement map he was using. Wrong video.

[@chuvanthuongvn]

firstly, for the original PM IC (never reball before) if you hot till the solder can come out like that for sure the CPU will over hit. second, the new PM IC if you are not reball before put in it is very high chance to damage CPU. and at last, before check with other LCD it was arabic language and after that it became english.

[@DEEPFIX]

First I thank you for watching our video and you post your questions or doubts in brief.changing the language is not a big deal. I wanna make you clear that,if you didn't do something it doesn't mean someone can't do that work . Do you think all our videos are not genuine?if you can check them all.

[@chuvanthuongvn]

accept the opinion to be good for later better than you deny it. I dont know, event dont care where you are but one thing for sure that i did iphone 6 more than times you eat per day. Br!

[@julioosilia]

+DEEP FIX you can have genuine videos but this is not one of those because you burn the digitizer chip control

[@arnonabuurs7297]

+Mr Chu I think you should make a real video :)!

[@arnonabuurs7297]

+Julio Osilia fully agree this is BULLSHIT.....they dont even use heat seal to shield other parts, just highly unprofessional

[@rezajavid1680]

amazing ,thanks for this, but how did you find the problem is the PM ?

[@mmfh9745]

Azubyk Samuel who asked ?

[@mmfh9745]

0% expensive equipment 100% pure skills

[@cristianbmc7205]

Congrats from chile, you are great electronic technician men !! grat job

[@loyalty786]

Hi i usually repair iphone screens etc never went to that that extent working with the circuit board but im interested to know what your actually replacing and what materials you have been using, Thank you ?

[@nitzanoz6128]

hey, two questions : 1. what is the temperature of the heat gun ? 2. after the soldering you are using DVM to measure impedance or short ? and what are the points on the board to do it, beside the gnd of course?

[@jaytan1744]

Hi Deep, what is the flux/raisin you used to take out/loosen the damaged pm chip? Is it the same flux for soldering and desoldering? Thanks

[@Kwame_addy]

how do you get replacement components? and how do i know which ones to stock for my repair shop

[@luiseg5198]

One question, what video camera do you use for the video? Thanks.

[@patricioreyes1008]

i thinks this a fake video repair, two reason first in minute 1:29 i see you lose 1 pin on board , second in minute 3:01 i see a two capacitor in short , bonus you stop video when change LCD .. any ways good Video .

[@nothin1456]

Fair point, however, the shorted capacitors could be in line which would be fine and they could easily be cleaned up via a quick solder iron touch :P. And not all of the pins needs to be intact on the bga or the PCB, some pins have no continuity or usage. Cheers!

[@nothin1456]

PS: Often times, if a pin breaks or cracks off the PCB easily, then there is a chance it will be a (useless) or (nothing) pin, as it wasn't really "gripping" anything but the board itself :) .

[@AtoZPoint-nj3jd]

Patricio Reyes thanks

[@janhoek1000]

this pin m10 is not nc

[@sebulica93]

the pin is not broken.if you look close enough you can see it's not well cleaned.probably it's oxidised

[@cybersed57]

Each time I see you perform a smartphone IC swap, I wonder how do you know that it's correctly positioned. Contact pads are minuscule and precision is critical.

[@yyou2860]

what is the product used in 0:15 and 1:00 and 2:00 , this is identical products ? is flux ?

[@KangParkSoon]

hello. wow you are a awesome expert for iphone fix anyway I have a question for you. this video running time "1:11" after removing PMIC, you hold brown strip? what name exactly? ^^ and you use liquid thing is that... flux? right? other one?

[@FixDaily]

You can use Kingboo flux. Also that's called solder wick

[@javanpohl1365]

Temperature (in C or F) and air flow setting, please!

[@marcoprogramas]

hi, Great videos, could you tell us what kind of solder paste are you using when removing ic and where to order it. Regards

[@MandangoGC]

Nice demo like always. So, the VBAT was in short? How you know in avance the issue is the PM IC and not the charging IC or some other one?

[@gamerslust6533]

Was that electrical glue you used to hold the pm in place?

[@cellncomprepairs5635]

asalam alle kum bhai kya baat hai MashaAllah, Allah tumhari illm mein aur izafa karre

[@stellarola]

That large soldering tip is just crazy. Where did you find such a tip?

[@mrsemifixit]

How do you know whether the ic is shorted or one of the surrounding smd caps? What temp did you use for removing the chip? Thanks

[@mohdfitry9602]

nice...very clear n understand vid.. 👍🏻

[@asrarhassan]

You're fixing stuff with that solder, lol damn awesome.

[@FixDevice]

Man, you are amazing! Greetings from Russia!

[@AndrewMooreJ]

For the love of God. Please, tell me where I am able to purchase those PMIC's.

[@AndrewMooreJ]

Thanks! few more questions. What temp are you preheating at? Also, what temp for hot air? This is all lead free right? What is your success rate with this? I just want to get an idea of the melting. Points. I prefer to use a k-type thermocouple with digital thermometer to assist in regulating the heat. Thats how I do it with my bag rework station for bigger bgas

[@DEEPFIX]

You can purchase it on online.

[@diesalweasel]

DEEP FIX Hi love your videos excellent stuff what you do. I'm new to all the rework. I my self have a hot air station. And I was wondering what temperature you use to remove and to install the chip and at what air flow rate would you recommend may I ask .Thanks in advance

[@kagobin]

安德鲁+摩尔 这个要看使用的拆焊台，如果是直风的拆焊台，拆IC也要看IC的大小，iPhone6的电源IC，拆解温度330度，风速4档，一定要均匀加热！

[@techbit7607]

Hi, what nozzle size, hot air temp, and pressure do you use?

[@sultanmirzapathan9972]

master of phone repair keep it up

[@urouro8901]

Can you please help me... after removing ic chip or any other, you have to clean that small (round circle) solder pins on motherboard...How to clean them without damaging the motherboard? I tried it once but i pulled the copper from the motherboard, basicly ruined it. Do i have to preheat the motherboard and then try with soldering gun and solder wick? What i did was putting soldering paste....using soldering gun over wick and trying to remove the extra solder from motherboard...the effect was clean motherboard but also pulling some small copper pins and in that way destroying the motherboard. Thank you in advacne for help...

[@ismaelolivos6724]

Hi, I saw your video from Chile and I would like to ask you if you know where I can buy the icepower for the iphone 6 thanks

[@riyadmarhez9547]

Sorry for my english but how it is you must change pm ic and not the component u2, do you have a tester

[@michaelyenge3487]

Fantastic work, I was just wondering if you can perhaps shot a video on how you can remove iCloud from iPhone 6, just like the iPhone 5 tutorial. Thanks much big fan.

[@jackytan1896]

when you repaired this device was it water damage? water indicator seems red to me

[@cityhunter087]

what temperature & air flow you are currently use?

[@jacquylenoir3550]

Good work, but to protect the other elements of the heat and risk of desoldering, place tape around the desoldering or welding element

[@chrisvillalon3169]

i was wondering what kind of solutions you used to removed the old chip and for the new chip?

[@simlock48]

Hi, How did You know that's big power management ic? There is small pm ic as well. How to determine which one needs to be replaced?

[@keithnsearle7393]

You will find out which part needs changing by the power it receives OR lack of power depending on the component. You will need a multi meter and an independent power supply to test out the different amps and volts of the components. Plus a schematic (circuit diagram) comes in handy.

[@simlock48]

Hi, THanks for Yor response. When I attach multimeter this way as You show in the video at 3 min 35 sec I get no beep and it only shows 301 continuity at the multimeter display. Does that mean that it's the big pm ic that needs to be replaced?

[@th2010]

Hello. Good Video. I have a few questions. What is the right temperature in C? What is right airflow level? Would you give some advice?

[@DEEPFIX]

Ok in next video we are going to provide audio and can find your answers in it...

[@th2010]

that would be very fine

[@alexgreen121]

th2010 , if you look at his other videos you can see the following settings temperature is set to 380 Air flow is set to 5 when he removes the chips, and by the air flow sound you can hear when he is putting the chip back, i would guess he lowers the air pressure to 4.

[@th2010]

perfect. thx

[@Tecnoangolo]

Ashfaq can you please tell me what kind of flux used , thanks and good job

[@antoniojimenez1767]

Very nice work. Happy to see your videos, thanks

[@Manny3564]

Hello Ashfaq, I'm very impressed with your knowledge and soldering skills. How did you acquire this knowledge and what type of training would you recommend? I just recently opened a Computer and Cell phone repair shop in the USA. Thanks, Manny

[@MrMarchinho89]

Hi, great work, where you buy pmic for iphone 6?

[@keithnsearle7393]

You can get them from "Ebay".

[@sergeantME54]

Hello, What temperature you use to remove components?

Hi ashfaq, I have a question for you. I've been replacing lots of screens and parts on all iPhone from 2007, but I've never managed to fix a "dead" motherboard. I have an iPhone 5S which started having problems with the sim. It would occasionally say "No SIM card installed". After some days it said "no SIM card installed" all the time, no matter how many reboots, change of sim, reinstall of firmware I did. After that I tried to fix it by opening it and make sure everything was connected properly, and then second problem came. The charging dock didn't work anymore. Sound from headphone worked, speaker worked. Only the charging didn't work. So I changed the headphone, power connectors cables in hope that it would fix it, but with the new cables it was still not charging or showing any sign of life. My question is this then, what do you think might be the problem. Since watching your videos you've done in the past in guessing it's the pm ic chip that is dead. But what about the issue with the sim card? Thank you in advance, keep up the good work. Regards from Denmark Francesco

[@GrimeReaperMan]

***** He doesn't reply to anyone

What's the point putting videos up then...

[@GrimeReaperMan]

***** I have no idea mate, he seems to upload these videos with no explanations at all. Though his video editing and quality skills have gotten better, we are still clueless on small details, no idea on what temperature he uses, what kind of flux, nothing. Don't get me wrong, he seems skilled, but that's about it.

I remember seeing a comment he did (one of the fews) where he actually said about the flux and temperature. But anyways to me it's no use, cause I do not have the equipment to fix this and neither the skills. (Looks like you need a pretty steady hand and a good magnifying glass) Thanks for the reply mate

[@FvckTheEU]

GrimeReaperMan new sim tray and good solder skills.....7/10 on the difficult meter

[@supinac17]

How did you recognize that PM IC must be changed ?

[@10MBorLess]

what are you doing with the negative and positive clips?

[@h.s.5102]

Hello how is called the heater you use and where can I buy it ?

[@chickiesmp]

ALL HIS VIDEOS ARE CORRECT,JUST BECAUSE YOU CANNOT DO SHIT DOESN'T MEAN SOME OTHERS CANT,I HAVE DONE THIS SEVERAL TIMES,ALL YOU NEED IS TO PRACTICE IT ON DEAD MOTHERBOARDS TILL YOU CAN DO IT RIGHT THEN DO IT FOR A PHONE YOU WANT TO REPAIR.DO SPORTS AND YOU WILL HAVE A STEADY HAND

[@hosseinm6752]

hi brother. what temperature do u use for remove pm ic on iphone 6. ???

[@rootsdat]

+Hossein M did u find out what proper temperature is to remove?

[@hosseinm6752]

+Pero it's better to preheat the motherboard till 100 degrees and then set your heater on 330 and set air pressure on 2 or 3 and you should keep check the IC till it's ready to remove and you have to do it qiuck

[@GTGTutoriais]

+DEEP FIX where u buy these pieces?

[@Pravinbholah]

hi where you get your IC's n chips plzz from Mauritius...

[@pakfones]

ohhh ashfaq is that you? well done.

[@mohammedziadan3331]

in the last when touch no work the language is Arabic , why it come English when the touch work again. you are lair

[@laserguy8673]

Look at the battery percentage

[@rajaafaqnusrat139]

Bhai ap khawiya knsa use kr rahy ho ?

[@glennferris2326]

where can I get replacement ic chips? and what does th letters pm stand for? and do you ever reball any ic's? and if so where can I get deal with a company who will have these chips as soon as they become available. .Any information you can give me would be helpful at this time. Thank You very much .

[@dabur872916]

pm stands for power management Apple/Dialog 338S1251-AZ Power Management IC

[@peteryu1489]

Hey love your video, your super talented and skilled. your video would be even better if you could explain how you diagnose the issue, your earlier video shows that. I think you should do the same for the newer video. Your channel is great for people who want to gain knowledge in this trade. Just an advice, keep posting :)

[@ePiCsL4Y]

I replaced the screen in my iPhone 6. The CPU and Home button got really hot so I disconnected the batter. The phone will not turn on again and is not detected my iTunes. Do you think the PM ic is the culprit?

[@pmastrandrikos]

what is the paste you use between ic and logicboard?

[@joseabraham9412]

Sir after ic removed your used cleaning items name pls tell

[@durgut81]

Sallam brother where do you get parts from Alibaba?Are the original or copy?

[@msjessieyang]

This is amazing video, but seems i cant get the temperature right, always end up overheating CPU. can you let me know what temperature is your heat gun set for this work?

[@Gayan.Weerasekara]

msjessieyang Me too

[@br0nzewhaler]

I cant remove the audio ic chip on an iphone 7 plus. At what temperature does it come off?

[@rdlynes]

How do you find out if the PMIC and screen need replacing if water damaged, I have two iPhone 6 and Samsung s6, both water damage both with not turn on?

Hi friend. Wy you replace the component? I don't see on description!

[@MarvelEpicstory]

hey what kind of glue you use?

[@luismt]

Me puede colaborar con qué temperatura trabajas la estación.

[@andrewsohkh]

hi, may I know where to purchase the PM IC in Singapore?

[@Juninhobass211]

I have an iPhone 6 as the battery discharges very fast , because I changed the battery and connector will be the problem , or know tell me which defective IC.

[@alexcornejo1811]

donde consigues los procesadores que le cambias?????

[@netdudeuk]

How did you know to replace that specific part ?

[@hendrymardiawan8899]

you are the man, great job

[@qaramanasqanli]

WHAT IS THE NAME OF THAT HEATING MACHINE AND WHERE CAN I FIND IT?/

[@KingPhoey]

No need to add new soldier?

[@MAXERKing100]

can i check out with a multimeter if the power chip works or not?

[@romano5497]

Which type of microscope do you use??

[@romano5497]

What brand and model?

[@MadalinPro]

I have a question, how is name that liquid wich you put on main board, brown..??

[@protechsolutions382]

Soldering Flux

[@wailfaza]

ماشاءالله عليك فنان 👍👌

[@chamundamobile9843]

How many air and hit , which smd use etc.

[@rumelbhuiyan]

U r very skill !I want to get ur skillness....!!

[@martel5948]

where can we buy all this tools? and replacing parts? Thanks :D

[@martel5948]

+David GL up!!!

[@TinuJangra]

o ashfaq bhai goog hai and bro chip kaha se parcheg krte ho i need chips all iphone cpu and pover ic

[@nathanatwell]

Repaired device had Arabic font. After digitizer failure, and "Changed LCD" the device showed English font. Nice try.

[@migisharomeo]

it's not easy to trick technician... saw that too

[@hookchen7128]

+N Atwell I think it's another iphone.

[@rafalszymecki813]

+N Atwell The fact that he removed the pmic without lifting pads (the one is NC) and resolder new one and he has spool of pmic chip means hes a pro and this solution absolutely will in most cases fix water damaged iphones. It turned on that means pmic working.

[@tastytechaddictsmtb]

You do realise the first activation screen scrolls between various languages dont you?............

[@janhoek1000]

the one is not nc, but 1v0pp

[@monkgts2200]

What is heat degree you are using

[@aldrine1986]

Awesome,can I need more details about you ? Where ru in abroad ?

[@aliali-et7xh]

What type flux you use? So easy to remove...i try to remove pm ic..so hard..it have glue ..at point solder..

[@scan4843]

HI SIR DO YOU HAVE YOUR OFFICE OR ONLY STORE FOR REPARING THANKS

[@aminamujahid227]

what is that thing your holding that is copper on 1:11

[@luismt]

Disculpa a cuantos grados colocas la calentadora

[@ludarry]

ese tipo de temperatura se debe utilizar para evitar dañar otros componentes

[@Monkey3353]

The keyboard was in Arabic and then I'll come to change the English

[@genmaxpain]

is there a fix for the replacement home button replacement? if you replace the home button(touch id) the iphone becomes a brick when you try to update

[@pawansharma747]

Superb Job Done!

[@abdali5500]

hello how are you please am asking about charging problem on iphone 6 I changed u2 ic ,USB control ic and change any part on charging area but dos not working (The device charging when it shut don

[@Nexalith]

what name of gel/glue for install that ic/chip?

[@samuelsantiago1835]

Muchas gracias por la información camarada éxito en lo haces

[@muhammadhafisnaguib4987]

bro, can u tell me your heat and air control for the blower?

[@adif4660]

Muhammad Hafis Naguib heat between 350c to 370c, depends on the hot air station. Always protect the other Ic with the kaptan tape or with metal plates..

[@gidbi]

Nice one... we have a 5s here ,suddenly went mad. only logo comes on sometimes red lcd,then goes off and then on again etc ... :/ any advice?

[@thomasdoucement3255]

how you shipped the support for mother board please ?

[@MarvelEpicstory]

kes type ka glue aap use karty hu?

[@moss786]

It's gel flux mate

[@melvinrodriguez1050]

Nice job!! Is there a way to remove iCloud by changing a chip on logic board?

[@hafizullahhafizullah9104]

Very good job Please whene u maid anothar videos remove music thank & really v.good job

[@richardredfern6282]

if you are fixing a dead iphone 6, just hold the top volume, home button, and power button at the same time. IF that doesnt work, connect your iphone to the computer