Mtk Cpu & eMMC Reballing And Installation

[@clivecottam1509]

skills on another level, I wish...

[@vijayjangra7986]

रेबाल sahi नही हो रहा नीचे cpu पर ppd इकट्ठा हो जाता h

[@MdPan-r9o]

Acche se video banao na explain karke

[@ArunkumarArun-ki2uv]

​@@vijayjangra7986mmlooop ,

[@kchemraj2047]

kya yr dimak to lagao mere bhai,chutiya bana rahahe tum ko,ek paile se he reboll kiya he,ye to asan se nikalta he,

[@valervaler9962]

The chip alignment at 6:12 was priceless :)

[@BenjaminObidike]

Pls where can I get this reballing net

[@arvindgarg393]

Hms practical badiya channel mobile repairing ke liye

[@SAhellenLily]

Thank you for making this outstanding contribution to those who can see this video。expect great movres not but just only in Mediatek chip ! Thanksgiving ❤ I leave Mediatek

[@samiraancio]

This video is a game changer! 🙌 The details on MTK CPU and eMMC reballing are super helpful. Can't wait to try this out! 💻🔧 Your expertise really shines through! Keep up the amazing work! 👍

[@diyfixtool830]

The Mtk Cpu & eMMC reballing and installation videos are great. Everything was explained calmly and in detail.

[@rareone46]

Please tell me the equipment names you used in video

[@ginyodquinoa7756]

if i'm not mistaken you had a pre heat underneath the board so thats why you easily remove the chip

[@almirandrade458]

The probability of rendering the chip useless using this method is very high. If the chip is small, soldering is faster, with larger chips you can even crack in the middle.

[@d347hw15h]

You could've blown away small stuff around the IC, use kapton tape to shield it from the heat and suction picker for the IC, much safer this way

[@daddybern24]

Could you reschedule me how to do this

[@markbarry6228]

​@bernardrobsons7402 how's next week sound?

[@daddybern24]

Sounds awesome

[@bytemyvoid]

if u ever use heatgun properly u would know that its impossible when u use such nozzle diameter newbies like to use thin diameter and thats why they blowing away smds.

[@gamerelated3887]

I love the fan cooling at the end! Great solution!

[@MmanzilsTech]

Thanks! 👍

[@Druid_Plow]

You can't make your own solder balls reliably. Almost a guarantee that one of those chips is shorting. They sell solder balls in very specific sizes for a reason, so you don't put too much solder on any one pad. Those screens, aren't for pushing solder paste through, they are for lining up actual balls of solder. Too much solder on 1 pad will bridge several.

[@Appri]

I agree with this, but again the guy got it working. He probably knows better than you... I know those stencils are only for solder balls, but if it works for him, it probably works for anyone else. He showed the chips with the "balls" on each pad, and they all seem to be fine, so no biggy,

[@fabian11235]

A stencil with solder paste is a viable way to re-ball a bga chips. Area of rectangular holes x thickness off the stencil = fixed volume --> same amount of solder on each pad. The execution in the video wasn't the best but that doesn't mean its not a perfectly good method.

[@Druid_Plow]

@@Appri he didn't show completed repair, it's very unlikely the repair works.

[@Druid_Plow]

@@fabian11235 it is not consistent at all, solder paste has inconsistently sized pieces in it And could have more or less solder in every tiny drop. And too much on 1 single pad will, not can, will bridge several pads.

[@Appri]

@@Druid_Plow people reball all the time, with this way as well. So just calm down and enjoy a man do his work.

[@dexdaps7018]

Good equipments & professional work

[@MmanzilsTech]

Thank you very much!

[@faizalfaizy899]

@@MmanzilsTechbro one dout pls tell…my motherboard is broken as 3 peace and droped under lake as 8 months now any chance to take datas?

[@southernflatland]

1. How you get this modern tin based solder to melt at 350c? I've never been able to even get the stuff to melt at any temperature below 370c. Unless maybe my thermal sensor was out of whack or something.. 🤷‍♂️ 2. Why didn't you use tweezers to lift the chips? Like, are you TRYING to knock other components loose? I spent around 5 years doing this sort of work, and I surely wouldn't have went about any of it that carelessly.

[@HeLrAiSiNg1]

Well his work suck i dont think its working prob 50/50 chance of it working now also what u mean modern tin based solder you might mean the grey paste stuff that thing melts at such low temps i fixed some chargers i had lying around for fun after buying such paste and it did melted at 250 with heat gun so less temp might be suficient too thing is its made of most paste and dust of solder thats why it melts in seconds in low temp whilst solid core rosin solder need higher temps cause is solid piece of tin rather than dust in flux if you take for ex the solder the plumbers or guys that install metal tubes etc its like normal solder but bigger in diameter this thing need blowtorch to melt a solder iron takes time to melt a blob out of it

[@southernflatland]

@@HeLrAiSiNg1 Dude, whether the solder was in paste form or not prior to chip installation, the metal melts together into the same solid metal when it's all said and done. And by federal law, since about 2007 or 2008, any solder used in mass manufacturing HAS to be tin based, lead based solder processing is too toxic for the factory workers and the environment. When he started, the chip was mounted on the board with fully solidified original factory solder. I couldn't care less if the factory used a solder paste or not, after the solder was heated and the chip was installed and cleaned, that solder was fully solidified metal.

[@ansh_virmani]

moreover he should use Blade to resize solder balls means to cut over solder balls ,making all balls shape and size PERFECT.

[@JuanGabrielOyolaCardona]

Thanks for sharing 😀👍 greetings from Colombia.

[@ricardos.6198]

Wow men, really is very strongly work that!!! The mission is accomplished?? 👏👏

[@A.A.A2222]

Perfect and good work👍🏼🌹😊

[@lakybegum667]

Awesome video❤ next plz....

[@mubasheer5584]

Don't try this on your expensive boards guys. You can limit heating your IC more than what shown in the video by proper method.

[@repairtechnician4666]

350- 360 c is good for cpu and emmc.

[@gershomsam8295]

Heat 340 air 40 time 1min 861dw

[@Mista_Godfather]

Of course not everyone has soldering iron with adjustable thermostat or heat gun

[@Utube_video]

380 air 40 is good for me

[@Adaptengkamadhureh]

Ok

[@magnet2011]

Thanks for sharing the details

[@czpanama]

Your supposed to use a special machine to remove and attach heat sensitive chips. Notice he didn't show you if it posted, or could see the onboarding emmc.

[@darkman19693]

how would this technique compare to traditional reballing with a preheater? I need to reball an Intel N100 cpu and i do not own a preheater.

[@SaidElbarnoussi-eh7sv]

Hello. I have a question, what you apply before you remove the shield??

[@darkfloyd5888]

Flux paste

[@KaccemKaccem]

Nice job sir Google❤

[@diyfixtool830]

This video was shared in great detail, thank you for sharing, I love it.

[@Darktophat_10]

DON'T copy what this guy is doing, bad heating job

[@KokoSword]

​@@Darktophat_10 thx mate

[@wf6951]

@@KokoSword You're welcome.

[@ijs106]

Você é um cara de coragem,conseguiu fazer rebaling com soprador.e eu nem com a máquina tive coragem . Brasil 😂😂😂

[@jorgeflorentin7921]

Excelente aporte colega,saludos desde Paraguay

[@carmelorossitto7084]

Well done. When I reball, some balls solder to the stencil. How do you do a perfect reballing? I tried everything but nothing changed. Maybe the stencil is not good or I should use 138c solder paste. I need your advice.

[@Aone.mobile]

1st. Clear everyone ic paid with singing (use ppd 183°+goodweek desolder wire) 2nd. Dry ppd (183) apply for rebolling 3rd. Heating =220-240 for rebolling

[@AMmobiletips]

Thanks for sharing the details 🎉🎉🎉

[@rwotopokaimmanuel]

I must raise the amount of tooth brushes 'cause they do a quite number of jobs not only tooth but also other things 😂😂

[@BenSunMobileCare]

Nice video bro, looks very satisfied

[@c__TattinhNhi]

It's so good I think it's so good it's perfect😊

[@anurasenarathna1703]

Wow. what a skill .!!!👋👋👋

[@rostyslav5334]

So as I understood, chip is auto-aligning itself to the pins on board?

[@davejones6130]

Speaking as someone who has repaired electronics for 40 years and is an electrical engineer I can’t help but think ; all this work and it’s only going to fail again from heat / cool cycles detaching the balls / chips esp without mechanical downforce. BGA is the worst thing ever for reliability - millions of devices dead before their time inflicting pain on consumers and their wallets !

[@prathmeshsobale7109]

How long will smartphone last after reballing ? Will it have same heat endurance capacity like before?

[@doug7180]

I'm glad I'm before this technology.

[@hphp7587]

Are you using low melt solder 138c? The balls are formed very fast at 280c.

[@ZahidMobileTech]

Masha Allah Bhai bohat acha good

[@ГордыйАзер-и7щ]

После перекатки чипа надо давать остывать от комнатной температуры, а не кулером , иначе припой может цирк потом устроить

[@hyppopotamm]

Тут видимо работа с гарантией в месяц. А что там дальше случится - не проблема автора.

[@СергейСамсонов-м8ф]

​@@hyppopotamm он скорей всего вообще не запустился проц перекатали а запаяли криво не отцентровали

[@thenarrator1408]

У нас 90% вот таких мастеров,главное не попасть к такому.

[@mixl4366]

You can change emmc or ufs to nvme ??? I subscribe you. after change emmc or ufs to nvme can right

[@abidaliyousafzai3123]

Nice job sir 👏 👍 👌

[@damianomartucci9814]

can you suggest the liquid flux model you use? I am struggling to find something useful.

[@MmanzilsTech]

Sd360 mechanic

[@abdulfaheem38]

Hello you do mobile repair if we send our mobile via courier?

[@AhmedRashed-e6g]

So beautiful sir❤

[@MP77987]

how much for ic repair usually?

[@gilbertknight6617]

How do the chips stick again to the board without solder ? Is using flux only work as a solder ?

[@brettgas2787]

?

[@babttech]

Good work🎉 ....please what's the name of the white nylon that gum the ic with stencil

[@yuzemir]

lehimleme sıcaklığı kaç olmalı çiplerde? bu yorum youtube aramalarda ilgili konuyu bulmaları için yazılmıştır teşekkürler

[@samudra62]

Saya dari Indonesia.sangat rekomendasi sekali videonya

[@RingZero]

Great work brother

[@MmanzilsTech]

Thanks ✌️

[@englishtime36]

Nice work sir 👏 👍

[@luckyjamestechs1779]

What is the volume of airflow of hot iron sir it is not included yet it's important also

[@luckyjamestechs1779]

Sorry it's hot air gun

[@sumitpaul6244]

@@luckyjamestechs1779 yes sir ,, what will be the air flow of hot air gun station

[@rosokkeliling]

Cepat tepat pas trik nya 👍👍👍💪💪💪

[@jameslivingstonelima6115]

Sir is that pasted ic? Can we remove ic with 007? Why there is no blue ?

[@FactsAndQuotes01]

Sir, aap kaun se camera use karte hain recording ke liye

[@wielijustice]

Is that paste lead-free ?? Cause if not lead-free.. The IC ball cannot handle the hot temp of the phone operation...

[@Appri]

What? You mean the opposite. If leaded, it can handle it.

[@wielijustice]

@@Appri no.. You said wrong.. Lead free is stronger

[@wielijustice]

If you are also a technician when Nokia Era... You know that BB5 type using lead free.. Like Nokia N70, 6600,7610, they are use lead free.. Many failure to detach them if you blow it with hot air too hot... Its hard attach because of lead free

[@Appri]

@@wielijustice "If not lead free, the ic ball cannot handle the hot temp." My god, reread what you said. Lead free is unleaded solder which takes higher temps. You said IF NOT LEAD FREE.

[@wielijustice]

@@Appri omg.. Yeah.. Sorry.. My bad.. Yes i mean lead free... Lead free should be used.. Cause android have high temp

[@АндрейБеляев-ж8ь]

мне интересно там все таки куча зелёных пятаков или это тако ищвращеный способ погреть чип?

[@VisualGadget]

Было страшно когда чипы переворачивал. Там же рассыпуха вокруг давно отпаялась, снести её так - как раз плюнуть.

[@reloadlives]

Вот я всегда удивлялся таким людям и их удаче. Снять-поставить не проблема, но если бы я так чип отбросил - вся мелочь в кучку бы собралась с вероятностью 146%. А они всю жизнь так могут делать и ничего...

[@hyppopotamm]

У китайцев ручонки мельче. Им проще :)

[@denistorFull]

Нижний подогрев сколько? Верхний мощность какая?

[@Big_BOSSSSSSS]

Он без нижнего работает

[@denistorFull]

Хер ты чипы поднимешь без нижнего... Скорее всего они отреболленые на свинец

[@dmitryderek4096]

@@Big_BOSSSSSSS да я тоже офигел от этого

[@chinaphonefixteam6300]

Hi man, great job.

[@pkcreation4883]

Sir cpu repearing krwana ka baad kitna din tak phone chal skta h tell me

Wow, thank you so much.

[@MmanzilsTech]

Welcome!

[@baphoneclinic680]

Good job oga

[@emigrant4life]

on the right side from above, you unsoldered a couple of elements 0:51

[@wolsalecom]

superb skills

[@nasreddinenasreddine2521]

the best bro go ahead

[@asiftak7810]

bro scrapper konsa hai achcha laga

[@salamtechmalayalam]

Good work👍

[@MmanzilsTech]

Thanks ✌️

[@jeromereforma807]

What liquid you put to the CPU and emmc.????

[@luckyphil_01]

What is the name of liquid used to remove the chips/cpu with heat?

[@jakhazardzn9862]

You forgot the transistor :)

[@gyvurjesus]

I want that my RAM be replaced with 8GB. Is it possible?

[@antonsorokin3881]

да, но вам нужно найти совместимую

[@HarpreetSingh-nl1li]

No

[@dbehterev]

In MacBook Air 2012-2013 was possible to replace soldered ram to 16Gb modules.

[@gsmtelecom5577]

@@antonsorokin3881 উঅ

[@avtarchanian]

Depends on mobile model

[@Gajendrauike609]

Mujhe daut h sir ye set on hua hoga bhi ya nii ????

[@fidelcatsro6948]

Waaah you can become heart surgeon, it has way less number of connections and piping!

[@thekadarjangdethekadarjang6878]

Usi mmc CPU ko lagana hai kya sir yeh new dalna hai kya

[@MmanzilsTech]

Usi ko ko lagana

[@SIVAPRASAD.TBADHUR]

In which and What course we have to study to learn this type of skills....?

[@litonsheikh7329]

Good job 👌

[@bipinchoudhury2476]

Bahut sahi tarika

[@hillarymandungumana1807]

Is it possible to recall a power ic if the overheating

[@joyhoward6105]

Equipment? Edit: mainly asking what that liquid used at the beginning is

[@VaraAbhiRam-wx5mw]

Bga flux paste(relief)

[@mugabirapaul8653]

GREAT WORK BRO

you are so skillful

[@ETBangla21]

beautiful ❤

[@caturprasetyo_2775]

Nice bro

[@MmanzilsTech]

Thanks

[@frankliniroabuchi6899]

Pls, can someone tell me the name of the tape used to hold the chip in place 🙏.

[@mohamedabid7052]

Interesting sir, I would like to contact you for replacing a cpu in a system board

[@TechnicalUmesh1]

Nice video

[@QasimAli-v5c5z]

Vivo y33 ki kit hai usmein fold hai vah wapasi karni hai

[@radhikasangepu5615]

after getting emmc repaired how many days the phone will work properly?

[@MattFixesStuff]

if the solder joints are the problem and you do a proper reball it should work for a very long time if not forever.

[@rareone46]

Please tell me the equipment names you used in video

[@mst.oyahidabegum2782]

What is the evidence that it is working? Why did not show the device on?

[@abidaliyousafzai3123]

Fantastic ✔

[@Raja-x1]

Kahan per hai aapka dukaan please bataiye bhai Jaisa bhi aap bata dijiye Ham vahan aaenge ki hamara mobile bahut din se kharab ho chuka hai

[@NisamNisham-hg5en]

1:50 asthafirullah voice ❤

[@neodiy]

350 degree c or f?

[@saif__YT]

Ooo hlo Etna der me to is ki maa bhen ho jayegi 😂😂😂😂😂jisko pta nhi h wo like kr diya lag gya hogya wo sahi trh chla ki nhi dekhao Etna tym me to gya IC 😂😂😂😂

[@williamvasconcellos6376]

Please what was the soldering temperature? There is no information in the video.

[@leonferko]

350°c +-10°c

[@MmanzilsTech]

350

[@ЮрийМел-в2о]

For me it is most exciting video last month

[@MDARSADHOSAN-t8p]

nice

[@fritzeraldvista2819]

Do you sell a pocof4gt motherboard?

[@sreejithc.a4147]

after rebal cpu outer thermal heat sink is necesoory