iPod Touch Battery Replacement Repair Guide for 2nd Gen

[@Repairsuniverseusa]

@Blackhawks107 Yes, this is a common issue. The best suggestion is to take it slow and use appropriate tools. Pry tools, flat head screwdrivers, etc, make a great deal of difference.

[@Repairsuniverseusa]

@tommydreamerrocks Yes, hard metal tools should not be used unless you are familiar with the repair. Safe open pry tools are suggested, as they are hard plastic and less likely to cause any damage.

[@Repairsuniverseusa]

@To0Papii Yes, most batteries will only have a limited charge by the time you do your repair. We suggest draining the battery fully, fully charging it, and repeat 2 more times. This has worked great for us for "breaking-in" a battery.

[@Repairsuniverseusa]

@asianswam Yes, this could be a battery issue. It could also be a dock issue. Check to make sure the dock port isn't damaged.

[@Repairsuniverseusa]

@arjanvlek The best way is to use a pry tool of some sort and pop it out. Some have quite a bit of adhesive, others seem to have little. Be gentle and slowly pry around it, you will eventually be able to lift it the rest of the way out. 3rd and 2nd gens are nearly identical, so should be no issue there. Good luck!

[@Repairsuniverseusa]

@pretzel1253 I would suggest holding down the home button, while the iTouch is unlocked. Normally only takes 10 seconds or so. Unsure if this will solve the issue, but worth a shot.

[@Repairsuniverseusa]

@XxxProudxxX You will need to de-solder the connection and remove the cable. You can then replace the battery and should be no issues. Good luck!

[@Repairsuniverseusa]

@failatfailing11 No, you can simply try splicing the wires, but this is not recommended as the reliability goes down. Simply twist the two ends together and make sure as much connection is made, then cover is electrical tape.

[@Repairsuniverseusa]

@cruiser277777 Glad you like it. Thanks for your kind comments.

[@Repairsuniverseusa]

@oalacord Normally, if all software options have been tried, the only hardware issue is the USB dock port. Normally replacing this can resolve the issue. We have never had this error appear for a damaged battery, but it is possible.

[@Repairsuniverseusa]

@MrBarrowzscape Normally 500 charging cycles, but there are a lot of variables. Normally last 2 years with heavy use, and up to 5+ with lighter use. But just like any other part, it can degrade faster due to things like moisture and how the battery was broken in.

[@Repairsuniverseusa]

@lucien0002 Sounds like a connection issue, likely caused by the solder. I would suggest attempting to resolder it, or if you are not comfortable, take it to a repair shop and just have them resolder the connection. I can't imagine somewhere local will charge you much for that.

[@Repairsuniverseusa]

@AwesomeComputerGuy Doubtful, could be a very temporary fix, but soldering is the sure way to get a good connection.

[@Repairsuniverseusa]

@failatfailing11 You will either need to use a screw extractor to remove the screw, or use a small drill bit to drill out the screw and remove. These are your two easiest options. As long as the flex cable is in the correct position, there should not be any issues.

[@Repairsuniverseusa]

@fusionstar916 If the battery is undamaged you can solder it back on. If not you will need a replacement.

[@Repairsuniverseusa]

@yourabigwinner I believe they are compatible with each other. I would carefully compare before replacement however. From my understanding, there is no difference between the two.

[@Repairsuniverseusa]

@urtypicalguy It is quite a simple repair. Just take your time and be patient. If you are not comfortable doing it you may consider taking it to a local repair shop.

[@Repairsuniverseusa]

@rkimberlyann Water damage is tricky. Opening up your Touch 2nd could give you more ideas of what could be causing it. Check the battery carefully, also check for damage to the motherboard.

[@Repairsuniverseusa]

@MexicanMuncher Could be a bad iron or bad contact. Test it out and make sure heat is being transferred. Does not take too much to de-solder the battery connection in most cases. Good luck!

[@Repairsuniverseusa]

@cityofcandypaint Depends on the reasons why it wont charge. Does it sync up with a computer? is the charge port damaged?

[@Repairsuniverseusa]

@ToastedTurd12 Do not worry it does not effect the use of the device.

[@Repairsuniverseusa]

Glad you like the video! Yes, all the different iPhone and iPod Touch batteries are different. They change every generation so make sure you get the correct one. We have all of them on the RepairsUniverse (dot) com web site.

[@Repairsuniverseusa]

@jay666rob Its best to have a reference (such as this video) to be sure you have it lined up properly. After the old battery is removed, it becomes quite obvious where the connection needs to sit. Once it is lined, just tack it down with a small amount of solder.

[@Repairsuniverseusa]

@BondoFox Yes, sounds like you have a 2nd Gen iPod Touch. Yes, our iPod batteries are the same batteries at was came in your iPod.

[@Repairsuniverseusa]

@bamaboy630 Yes. A replacement will get you a good charge again like when the iPod was new.

[@Repairsuniverseusa]

@billybee48 With water damage its always hard to say for 100% what the issue is. It could be motherboard or battery. You may want to try changing the battery as these are low cost parts and it could fix your iPod.

[@Repairsuniverseusa]

Being subtle is a key to removing any panels to this device. This pry tool is not meant for twisting or bending, simply prying and sliding.

[@Repairsuniverseusa]

@rossie101 Yes, but it is repairable with a replacement part. Which ribbon did you break?

[@dadexter88]

Fantastic video. Thank you!!! I would have had NO idea what I was walking into or what to have done if I hadn't seen this. You're saving people's "lives" (their iPods). Thanks for taking the time to make this video.

[@Repairsuniverseusa]

@Jonathannovak1 The screen won't come apart in 2 pieces as it is attached to the mid frame. However we recommend you replace the touch screen at the same time before it gets worse. Both battery and glass touch screen replacements are available at RepairsUniverse (dot) com

[@Repairsuniverseusa]

@Fal1ingUp Could be a battery issue. You may want to consider replacing.

[@Repairsuniverseusa]

@ShizzlePDX503 Neither. You just need a small phillips screwdriver for the iPod Touch battery installation

[@Repairsuniverseusa]

@failatfailing11 You will need a soldering iron, solder, and electrical tape. There are many guides here on KZbin you can use to learn the basics and preform the act yourself.

[@Repairsuniverseusa]

@lagrandecomission You just need a soldering iron, a pry tool and a small Phillips screwdriver.

[@Repairsuniverseusa]

@Mattayl101 Alternative? Anything that has a "+" shape that is sturdy may do the trick.

[@Repairsuniverseusa]

@lucien0002 Ah I see. Sorry to hear. Motherboard damage usually makes the device considered "totaled". Many of these types of repairs are quite simple, put patients is also a necessity when conducting a repair such as this.

[@Repairsuniverseusa]

@TheLinuxlife No problem. Glad we could help.

[@Repairsuniverseusa]

@NvdVen Yes, it is an original battery.

[@Repairsuniverseusa]

@krackmunkie08 Yes, sadly there is no other alternative. Once a ribbon cable has been ripped or damaged there is no way to repair it, it must be replaced.

[@Repairsuniverseusa]

We ask ourselves the same question, lol. Hopefully this video will help, best of luck!

[@Repairsuniverseusa]

@MrPoco123 The setup of the 4G is quite a bit different from the older generation. Check out our take apart guides for the 4G in our channel.

[@Repairsuniverseusa]

@Assassin2397 This is a "safe open pry tool". We have these and many other pry tools available at RepairsUniverse (dot) com under our "Repair Tools" section.

[@Repairsuniverseusa]

@TheHoesWife Yes, if its not powering at all it could be the battery. We have these replacements at RepairsUniverse (dot) com

[@Repairsuniverseusa]

@HardcoreJeroen No, I don't believe this is an option you can turn off. The device will always charge when connected to the computer or mains.

[@Repairsuniverseusa]

@MrLadiesman93 Tinning means adding a little solder to the connections.

[@Repairsuniverseusa]

@Oilasor925 Will you iPod not power at all? Any life even when on the charger or synced to the PC?

[@Repairsuniverseusa]

Normally the battery would not cause a dim screen, a quick test would be to plug the device in. If it functions fine, the yes, the battery may be to blame. However it will likely stay dim as it is the LCD screen that is the cause - assuming there has been no motherboard damage to the device (water damage usually).

[@Repairsuniverseusa]

@pretzel1253 Just to clarify, is the screen pure white - this would likely be LCD damage, or is the screen colors inversed like on the iPhone 4G? Or is the screen mostly white with discoloration, etc?

[@Repairsuniverseusa]

@missourirock You will need a soldering iron to heat the connections.

[@alexander101207]

What a project for a battery. I love Ipods, but also have a Blackberry and wish the replacement for Ipod was as easy as Blackberry!

[@Repairsuniverseusa]

You can place packing tape over the screen to prevent shatter.

[@Repairsuniverseusa]

@lagrandecomission Just a soldering iron and some solder.

[@Repairsuniverseusa]

@mariakevin15 Glad we could help with your iPod Touch repair.

[@Repairsuniverseusa]

@sravisashi Yes, check the tools section on our web site.

[@Repairsuniverseusa]

@whinstaile21 Not a problem, hope your repair goes well!

[@Repairsuniverseusa]

Yes a solderer is needed to release the battery connection.

[@Repairsuniverseusa]

Depending on what caused the initial battery to fail, this could be a damaged board. Also you want to double check the installation for connections.

[@Repairsuniverseusa]

@dadexter88 No problem, glad we could help!

[@Repairsuniverseusa]

@tsimanjuntak No. All the iPhone, and iPod generations use different batteries. You can find all the different iphone and iPod Batteries at RepairsUniverse (dot) com

[@Repairsuniverseusa]

@j69d A batter replacement would be your best bet. If it had more juice it will likely be able to fully boot up. Also hook it up to iTunes and make sure it does recognize the iPod (it should). You can find replacement batteries at RepairsUniverse (dot) com.

[@Repairsuniverseusa]

Yes, we ship worldwide.

[@Repairsuniverseusa]

@maraxani Thanks, we are. We do these repairs day in day out. Repair Services are available at RepairsUniverse (dot) com

[@Repairsuniverseusa]

@Smoenator Yes, you need a replacement battery. You can find these at RepairsUniverse (dot) com

[@Repairsuniverseusa]

It can be the MB. This also depends on what caused the damage such as water damage..

[@Repairsuniverseusa]

@wondledonkey As far as we know, that is is the only way to connect to that circuit.

[@Repairsuniverseusa]

@whinstaile21 Soldering the connection is the recommended method.

[@Repairsuniverseusa]

@mikeconan13 No, all the files and settings on your iPod will stay exactly the same.

[@ragauli]

does repairs universe give soldering tools along with their usual repair kit.. what is the cost of battery plus all the tools. my battery still works but doesnt last for more than 24 hours even when idle. it is kinda erratic sometimes it will last for two days. but at other times it will discharge within few hours. can i improve the performance of this battery. the ipod is more than 3yrs old or shd i go for a battery replacement. I am kind of tired charging it again and again

[@Repairsuniverseusa]

@penwuin Ok, we have replacements on the RepairsUniverse (dot) com web site.

[@Repairsuniverseusa]

I wouldn't think there is much demand for them at the moment but we'll probably have some in the next few months.

[@KarthikNagarajan]

Very helpful video. Thank you, and can you help me with what Wattage and Temperaturre to be used for the soldering?

[@Repairsuniverseusa]

@asquaredjsquared With water damage its always hard to know 100%. I would leave it off in rice for over 24 hours before powering back on.

[@JGSHD]

@RepairsUniverse so what would i mostly need to replace cause my ipod would og reall dim/dark from time to time and now it's just staying really dark and dim, would i need to replace the battery or the LCD screen and is there a way of knowing what to replace and what not to?

[@Repairsuniverseusa]

@MichielWS If its not taking charge of not holding charge for long then yes, it sounds like a battery issue. You can get the replacements at RepairsUniverse (dot) com

[@Repairsuniverseusa]

@carydowney Sounds like your battery has run its course and needs replacing. you can find the replacement batteries at RepairsUniverse (dot) com

[@panappakkam1891]

thank you what is the cost totally. where to get the battery replaced safely

[@Repairsuniverseusa]

@iluvrunescape114 Sounds like your battery is bad. This happens with rechargeable batteries over time. To solve this you will need a replacement battery. You can find these at RepairsUniverse (dot) com

[@JGSHD]

@RepairsUniverse I have an ipod 2nd gen for a while now it's built up some dust behind the screen and recently the screen has gone really dark i can barely see what im doing do you recommend me taking it apart and changing the battery if that's the problem? Please reply.

[@failatfailing11]

@RepairsUniverse btw is there any other way to fix the connections to the motherboard so i can attach the new battery? i dont hav a soldering iron, or solder, please help!

[@Repairsuniverseusa]

@thehockeyfan8888 It will need to be soldered back onto the motherboard.

[@Repairsuniverseusa]

It really depends on what kind of damage was done. Leave the device in a bag of rice overnight to soak up all the water, then try connecting it to a computer to see if iTunes recognizes it. If it is recognized, then it is likely the motherboard is functioning correctly. If it not recognized then it is likely the motherboard was damaged and the device would be considered "totaled".

[@iamthesivart]

How and or where do I get the safe open pry tools? I have never even heard of them before.

[@failatfailing11]

what tools do u need to solder and how do u solder? please answer!! i need help!!

[@Repairsuniverseusa]

@darkchew12 I'm sure Apple will do the repair, but don't expect them to do it for under $150, it may even be $200.

[@Repairsuniverseusa]

@xAnsuXX Replacements are available at RepairsUniverse (dot) com.

[@Repairsuniverseusa]

What does the error message say that the iPod displays?

[@numex106]

this is a great video but how do you know which is is ground or positive ???

[@Federico84]

so should i use a solderer or what to remove the connection of the battery?

[@BOGOWA22]

Great video! Step by step; very easy to follow. i plan to do the replacement myself when my iPT's battery dies. One quick question: does 2G share the same battery as the same battery with the 1G or iPhone? i mean, should i worry about incompatibility if i get a replacement package for 1G iPT or for iPhone. Appreciate it.

[@Repairsuniverseusa]

@cityofcandypaint Replacing the battery could resolve the issue, assuming it is the battery that is faulty. Check out our replacement parts for the Touch 2nd Gen at RepairsUniverse (dot) com.

[@BOGOWA22]

Thanks for the quick reply. Geez, glad that i didn't rush to buy the package meant for different iPT. Awesome. i will certainly check out RepairsUniverse's catalog online.

[@failatfailing11]

@RepairsUniverse when i was unscrewing the 7 bolts on the metal thingy, one became stripped, do u know how ot deal with it? and also i removed this bronze button where the home button used to be, is that a prob.? please help, thanks

[@Jonathannovak1]

I have a question: the glass screen on my iPod touch (2nd gen) has one long crack that extends from the middle right side down to the bottom left. It goes from the right metal edge to the left metal edge. If I remove the screen to replace the battery, will the glass come off in two parts, and will I need to replace it?

[@MrLadiesman93]

What do you mean when you say "tinning the connections" on the new battery?

[@tsimanjuntak]

@repairuniverse are the battery ipod touch 2g 8gb is the same with battery iphone 3gs?

[@Repairsuniverseusa]

Sounds like it could an installation issue or further damage to the device.

[@claytonchar9232]

Thank you for your very informative video. It convinced me that I should have a professional replace the battery on my iPod Touch instead of doing it myself. I'm all thumbs when working (destroying) miniature ribbon cables, screws, and printed circuit boards.

[@TheInfamousIceman]

@RepairsUniverse hey man..how much does a second generation battery cost?

[@Repairsuniverseusa]

@budaksekolah87 Take a look at our iPod Touch 4th Gen take apart guide, it has quite a bit of the information about disassembly.

[@BondoFox]

I think this is what I'm going to need to do with my iPod Touch. Trouble is, how do I know which generation it is? I won it as part of a Grand Prize package in a sweepstakes a couple of years ago, and all I know is that it holds 8 gigabytes of music and video. BTW, are the batteries you sell Apple OEM? Thank you!