690 engagement points and an amazing sound are tradeoffs for poor bearing life and broken axles. We now know the Industry 9 Hydra’s unique design suffers these issues. So what can you do about it?
Пікірлер: 229
@industrynine39319 ай бұрын
We appreciate the feedback and thorough evaluation of our Hydra hubs. We made a running change to our axles to eliminate the stress riser at the bearing journal adjacent to the FH body as was noted in the video. We have been using these updated axles in our service department for over a year and once we confirmed this had corrected the issue, we made the running change to all production hubs in June. We have not had a single failure we are aware of to date with the updated design.
@WheelworksHandcraftedWheels9 ай бұрын
Is that the "stress riser washer kit" axle which is available? Great to hear that it's corrected the issue as the Hydra is such a unique hub with incredible features. ~Tristan
@industrynine39319 ай бұрын
@@WheelworksHandcraftedWheels - Yes, we've been shipping the updated axle in new builds since June, and have been offering it exclusively as the warranty replacement prior to the BOM change. It's also available from our webstore for any riders that would like to fit the updated axle to their hubs.
@LaurentiusTriarius9 ай бұрын
@@industrynine3931 wouldn't be beneficial to have a cromoly & titanium version of the axle instead of an aluminum alloy?
@danjelvantijnintellijel7569 ай бұрын
In the video he shows the new design from Mid 2022 as still being flawed. So just to be clear the "stress riser washer kit" axle is different than this mid 2022 design and has only been in production units since June 2023?
@MTBPoloАй бұрын
The same problem is also from Torch. I have destroyed the second freewheel in which my bearings broke completely. I paid 500€ for the hub and then changed the freewheel 2 times which each cost 250€. So I paid 1000€ for this super hub and in the end I threw it in the trash and bought a reliable DT Swiss.
@Ali_Clarkson9 ай бұрын
I'm a trials rider using Hydra hubs on all my bikes from comp trials, street trials, MTB and E-Bike. I must admit when the hubs first came out I was reluctant to try them as trials depends on strong engagements and often the more engagements you have the less reliable they get. I did eventually dive in and get a set and I haven't had any issues yet. My oldest pair are on my street trials bike and are 3 years old I think, still on the same bearings, same internals and same lube/grease from the factory. In fact, the bearing life has impressed me as I've had issues with bearings on Hope hubs in the past. My MTB and E-bike wheels are only 6 months old but they're still perfect too with no skips on any of my hubs either.
@WheelworksHandcraftedWheels9 ай бұрын
That's really interesting. As I said in the vid we see much better service life on hardtails so I'm wondering if the super stiff back end of a trails bike really helps these hubs? -Tristan
@hardtruth6039 ай бұрын
The HT thing could be a thing, also note that his Trials rear end isn't 148, it's 135/142 and uses a bolt in axle, not slide through/TA like most use, so yes, much stiffer. Thanks for chiming in Ali, but you forgot to mention one critical bit of info, that you're sponsored by Industry Nine, so yeah, um.....
@Ali_Clarkson9 ай бұрын
@@hardtruth603 almost right, it is 135mm but it’s also a 12mm thru axle. My MTB I use for trials as well as trails is 142mm too but I haven’t had that as long. And yeah I get free product from I9 but I always like to be honest and I wouldn’t be scared of saying if I’d had any issues. I was getting free products from them back when the Torch was the top model, they offered me the Hydra when it first came out but I refused as I simply didn’t trust that many engagements for trials and I went and used Chris King hubs for two years while others put the Hydra to the test. Once I was satisfied it could work for trials (Danny Mac had been using one with no issues) I was happy to start using them myself…I only ever use products I am genuinely pleased with as I’m too much of a perfectionist and gear geek to accept products that don’t work how I want them to
@andykrull92979 ай бұрын
Similar experience here. No longer into trials, but I value the fast engagement. No failures here on a RM Slayer. Servicing is just too easy in these things!
@AlexeiPavlov7 ай бұрын
you must be very light
@ThunderStruckMTB9 ай бұрын
As an admitted DT Swiss fanboy who once strayed to the allure of shiny, loud things made by I9, only to be immediately regretful, I watch this video with a smile on my face and a slow engaging 36T ratchet hub that is utterly bomb proof attached to my bike.
@zwingler9 ай бұрын
My grin goes from ear to ear. But hey, im sure its covered under wArRaNtY.
@trailjockeytj61609 ай бұрын
I do like the 240s for simplicity and weight, but I do enjoy engagement and switched to onyx and take the weight penalty! Bomber, hubs, and absolutely instantaneous engagement!
@trailjockeytj61609 ай бұрын
I used to run a Chris King, and did love the beehive buzz, but since then have been a onyx fan, a little bit of a weight penalty in the very center. Of my wheel, but the engagement is well worth it! Plus all the bling, or any bling you want! What do you guys think of the new rope spokes? I’m thinking my next bill will be a onyx Hub., With bird spokes. Because they have a Hub made for those spokes now.
@mrvwbug44239 ай бұрын
The 54t ratchet is pretty nice, and still quite bombproof.
@doctajuice9 ай бұрын
The ratchet ring system also has the advantage of all teeth engaging at the same time so the connection feels super solid when it hooks up. I say this an a i9 torch owner but I definitely love the feeling of the dt hubs when I ride friends bikes
@ionicman19 ай бұрын
Nice to see this issue being publicized a bit instead of pretending this isn't happening. I've run into this problem several times and have a few points to add: 1. This also happens to 1/1 hubs even though they don't have engineered pawl flex. I've broken 3 1/1 axles, they always break at the same stress riser spot. 2. Do not count on your hub to start creaking if it is breaking/broken. Inspect the axle when you do regular services! You'll see stress fractures forming in this area before it fully breaks. The first time my axle failed (I didn't yet know it was possible), I got no indication anything was wrong until my wheel axle failed as well (because the hub axle had already broken) causing my rear wheel to jam and lock up. Had a big crash as a result. 3. At least for the 1/1 which is not supposed to flex, the steel 'forever' axle from Pinner has been a great solution for me. Wheel/axle interface is noticeably stiffer and at least so far appears to be holding up well. I will say that I9 always got me a new axle quickly whenever I had this issue, but it just became too big of a liability worrying about when it might (will) fail next. Also for some reason you can't buy the 1/1 axles off the shelf so it was impossible to keep a spare in my toolbox.
@brettperchaluk52529 ай бұрын
Was going to share the same outcome with 1/1 hubs. Broken axle, very short bearing lifespans. And, I could "press" the bearings in with one finger (even on the second warranty-replaced hub). I'd like to trust I9 because on paper they are a fairly competitive hub, but the maintenance and reliability issues sent me away.
@thomasseymour41909 ай бұрын
Thank you for posting this. I am also a wheel builder and have gotten some strange looks when discussing this with clients. I appreciate the improvements to the axle design and I’ve also noticed a significant improvement in bearing smoothness on the hubs I’ve received this season. I understand why people like these hubs and it’s nice to see i9 attempting to address the weak points of the design. As for me, I own 4 bikes, all have DT 240 or 350 hubs.
@PeakTorque10 ай бұрын
Its single pawl engagement - happens in many traditional hubs, due to tolerances. But happens in Hydras by design, absolutely crazy. Single pawl engagement puts a huge radial load on the bearing and axles, and that's why they're failing. Best thing to do is by a dt240. Failures probably more common on full sus because of single pawl engagement (high radial loads) under harsh pedal kickback (drops at slow speeds). Doesn't happen on hardtails.
@JesusRescuesUs3-169 ай бұрын
As an owner of the Hydra hubs, thank you for this video and lessons learned. The real issue is anything mechanical has a failure point. And any good manufacture can learn from and make the necessary design changes as noted by Industry Nine in the feed.
@Lou-f9 ай бұрын
I’ve had my hydra hub since launch, still works great. I do my own bike maintenance.
@SteezeShop9 ай бұрын
Wow, I respect you guys for pointing out a flaw from a company without simply bashing them for no reason.
@WheelworksHandcraftedWheels9 ай бұрын
🙏
@jaro69859 ай бұрын
They were a bit too kind IMO. I9 designed a defective product, its fair to call them out on it.
@paulflory35329 ай бұрын
Brings to mind a terrifying experience from many years ago when sealed bearing hubs were becoming a "Thing", Phil Wood, etc making them. In a race, I won a set of sealed bearing hubs by a manufacturer I'd never heard of (and can't remember) and built them up as wheels for training. All was well until some weeks later I was in a practice race at the Rose Bowl in Pasadena. Had just begun a stint at the front, and as I folded the bike into the first 90 deg right turn at the bottom of the course, one of the rear wheel hub flanges exploded, and the rim and tire moved over and locked up against the chain stays. I couldn't turn and shot straight across the intersection, fortunately no cross traffic, tire wore down to the casing at the one spot but did not blow. All the other riders made the turn no problem, thankfully. Examination revealed that whole chunks of the flange had torn loose, and fatigue cracks emanated from other spoke holes in that flange, the other rear flange, and both flanges of the front wheel as well. The flanges were much thicker than those of the Campy hubs I was used to, making me wonder if they were cast aluminum rather than forged? Before someone informs me I overtightened the spokes, I'll point out that I never saw this problem (or any other) with wheels I built using Campy or Phil Wood hubs. And the reason I was building my own wheels was that I was racing on a very limited budget.
@WheelworksHandcraftedWheels9 ай бұрын
That sounds like the glory days of CNC components! Apparently a slowdown in the aerospace industry left a bunch of CNC machines with excess capacity so up sprouted a bunch of companies CNCing *everything* and anodising it purple -Tristan
@paulflory35329 ай бұрын
@@WheelworksHandcraftedWheels Really wish I had a photo of it. don't recall that the exterior looked smooth as I would expect (?) from machining, not anodized. We're talking early 1970's, dark ages.
@lazylearner96710 ай бұрын
Bearings were my big issue when I had the Hydras on my Ripley. I would go through 2-3 sets per year. I have never had that on any other hub over the past 19 years. I do climb about 200k per year and about 1700-2000 miles, all on dirt in Utah. Hadley hubs are really good but Kings are my favorite. The new Hope Pro 5's also look interesting.
@WheelworksHandcraftedWheels9 ай бұрын
What I've observed over the years but never quantified is the impact that the frame has on hub bearing life. Most frames are reasonably flexy and reasonably misaligned (hey, nothing can be manufactured perfectly) and the specific flex pattern of a frame can affect Hub A more than Hub B, even if both of those hubs display similar bearing life on different frames. Maybe your Ripley frame was just a poor match for the Hydra? -Tristan
@lazylearner9679 ай бұрын
@@WheelworksHandcraftedWheels cool that makes sense.
@ultimatist9 ай бұрын
@@WheelworksHandcraftedWheels yep, this. Even something like riding style - for example, if you lean the bike more and your body less in a turn vs. always keeping your weight in the plane of the seatpost - can drastically impact the forces on your BB, which transfer to both axles and hubs.
@anthonyhebert-trudeau699510 ай бұрын
I've had Hydra hubs for 2 years now and they skip from time to time as if the leaf spring weren't stiff enough to bring the pawl to fit inside the ratchet ring fast enough. This skipping only occurs on the first engagement when you start pedalling hard. I9 changed my hub on warranty but I expect bearings to give away next year. Can't tell about the axle but this video is pretty clear to me. Conclusion for hubs: High POE, Reliability, reasonable price... you can only have 2!
@scrappy75719 ай бұрын
I have the same skipping on my Torch hub. Usually after coasting, and then engage, can hear a loud snap/crunch noise. Annoying, and other than it eats cluster hub bearings it's been fine.
@Christ_Our_Life2 ай бұрын
Contacted I9 about the updated axle since I was replacing all the bearings and they sent me the axle and kit no questions asked. First time on Hydra and I’m liking it, but I also have a wheel set with Onyx so it’s not that much difference in the engagement. I have had the pawl hang up a little… my wheel set is $1800 Ibis carbon so no complaints. I prefer instant engagement because of the trails I ride it helps a lot and I’m disabled and getting older and need all the help I can get, but that doesn’t mean I’ll get an e-bike. Thanks for the video!
@benbonoma21879 ай бұрын
Fantastic video. I’ve snapped 2 axles already and wasn’t sure what’s going on. Good to understand the detail behind the design and it’s pros and cons. I still love my I9 Hydras, but I now have the information to maintain them better than before. Thank you!
@WheelworksHandcraftedWheels9 ай бұрын
Glad it helped! Have you been using the "stress riser washer kit" axles? industrynine.com/parts/axles -Tristan
@benbonoma21879 ай бұрын
@@WheelworksHandcraftedWheels I don't think so but I will start when they need replacing.
@AlexeiPavlov7 ай бұрын
you still love them? 3 comments above the guy says "Do not count on your hub to start creaking if it is breaking/broken. Inspect the axle when you do regular services! You'll see stress fractures forming in this area before it fully breaks. The first time my axle failed (I didn't yet know it was possible), I got no indication anything was wrong until my wheel axle failed as well (because the hub axle had already broken) causing my rear wheel to jam and lock up. Had a big crash as a result."
@ryanmichels29819 ай бұрын
I have i9 101 hubs. Think they’re a great balance between cost, engagement, and reliability. No issues so far after over a year of use. This is a really interesting vid, I didn’t realize these hydra hubs only engaged 1 pawl at a time.
@richroberts8238Ай бұрын
Great analysis. As someone who spent 30 plus years in industrial maintenance issues related to machine shop work on say pump shafts and failures related to stress risers from sharp transitions were addressed by changing the machining to eliminate those sharp edged cuts. Since most cartridge bearings do not have sharp edges but have slightly radiuses edges simply matching axle radius to the bearing edge radius should make a difference. Requires mod to machining not sticking a washer in the critical location.
@WheelworksHandcraftedWheelsАй бұрын
Interestingly the new Solix hubs have a very large radius on that part of the axle and do not have the 'stress washer kit'. It's worth noting we haven't seen any issues with the 'stress washer kit' axles and they seem to increase bearing life -Tristan
@travistweedle96749 ай бұрын
Two wheelsets with Hydra hubs and never had a problem. Been riding the first set since 21' and the other since 22' both with over 3k miles on them both on Enduro bikes that get ridden like I stole them. No mechanical issues of any kind. They were built by I9 and have their aluminum spokes also.
@sprungmass9 ай бұрын
Perfectly timed video, thank you! This triggered some research and looks like I will be getting a steel "forever axle" by a company in Whistler. Easier to replace a freehub body out on a bike trip instead of finding and replacing axle/bearings.
@adoonjackson26059 ай бұрын
Been beating the shit out of one of those for the later half of this season and its held up to hundreds of miles of riding and almost 20 days in the park, highly recommend
@SpokesmanMTB9 ай бұрын
What is the steel axle companies response to the idea that the axle must flex? Does the steel axle flex in the same way as the aluminum? Is it not an issue?
@sprungmass9 ай бұрын
@@SpokesmanMTB It should be able to flex enough for the pawl to engage otherwise the product wouldn't work or exist. They are called "Pinner Machine Shop"
@jamisonr9 ай бұрын
No issues with my I9 but I've only had them since March. I was aware of the axle issue from MTBR forums. I think I'll just get extra axles and bearings, I like the hubs and engagement too much to worry about having a few more parts to worry about. Back around 2008, I actually had a pawl go through a Campagnolo Record 10s hub and jam in the middle of a hundred mile hilly ride, that was a real pain! Might be the only DNF for an event I ever had. I have it in a box somewhere, might need to get that out and make a desk ornament out of it. Thanks for the info, I'll take all of this advice to heart.
@RJ_Groot9 ай бұрын
I had Pinner Machine shop build me one of his stainless axles for my hydra after it broke the aluminum one. It has never worked as good as it does now. Do yourself a favour and get yourself one. It functions perfectly and the bearings now last more than a few months. It's an amazing hub now that it has a better axle.
@ionicman19 ай бұрын
Yep - broke my 1/1 axle 3 times before going the Pinner route. Works great - wheel/axle interface is noticeably stiffer, better bearing life and so far, no more broken axles.
@adoonjackson26059 ай бұрын
My thoughts exactly
@tstodgell9 ай бұрын
The Hydra hub mechanism is an compliant structure that uses freehub and axle flex to make the 690 points of engagement happen. Unfortunately this also results in poor bearing life and ultimately, axle failure. Aluminum has a finite fatigue life and they've built a hub that uses aluminum as a spring. It's a ticking time bomb.
@seanmccuen69709 ай бұрын
lol, what could go wrong...
@Bonky-wonky9 ай бұрын
Over 60 POE is only “useful” on the parking lot or when riding trials.
@joelankeny62779 ай бұрын
This video makes me really glad I went with a DT Swiss 350 hub (with the 54t ratchet). The mechanic at my LBS mentioned this problem with I9’s when I was choosing a hub and ultimately he’s found the DT Swiss hubs are nearly indestructible even when abused. Being a budget a reliable and easy to maintain hub was super important.
@robinclaidlaw9 ай бұрын
It isn’t that aluminium is a stiff material, it’s a lot more flexible than steel, size for size. But it’s much lighter, so by using more and making things bigger diameter you can make it stiff. Furthermore, because aluminium suffers from fatigue cracking, you NEED to design it to be stiff and avoid cyclic flex or it will break. A steel or titanium axle could tolerate this, but it would be hard to design it to be flexible enough while maintaining the diameter, which is needed for the through axle. Out of interest, fatigue life tests on cylindrical parts are often done by forcing the part into a bent shape then rotating it, so the life of these axles is a hard one.
@d.tommueller92229 ай бұрын
I agree with this. My experience though was the cheapest component didn’t fail. The freehub spur ring developed cracks and the pawl pockets stretched. Both of these caused the hub to ‘pop’ quite a bit. This required lacing in a new hub that I9 did not cover under any warranty. I’m an old weak guy and did regular service using the recommended oil and grease. So not sold any longer on the I9 Koolaid. May consider an Onyx hub in the future but definitely will do research beforehand.
@and30ers10 ай бұрын
I've had DT Swiss hubs for 15 years now and have no plans to change. All 36 teeth engages all the time. It just works.
@ambushell57789 ай бұрын
I have a Hydra hubset that has 3+ years of very hard enduro and park riding on it. Earlier this year I did a full rebuild on it including all new bearings and replacing the original axle design with the new one. The old one had a bit of wear, but was still functional and silent. I theorize my hub might last longer because it's been on the back of a Santa Cruz frame, which has a very solid and stiff rear triangle. There is a "nuclear option" for replacement axles- the Pinner Machine Works axle is steel and is seriously beefy. I didn't feel I needed it, nor did I want the extra weight. but that's an option for heavier riders or flexier frames.
@RyanBuildsWheels10 ай бұрын
A sleeve of some sort was my first thought too in this case, an interesting take :-).
@ttengineer4049 ай бұрын
id love to see you do this type of video on all major hubs. Especially the Onyx Classic and Vesper.
@haentz9 ай бұрын
Yeah, I would love to get a wheelset with the Onyx hubs but I'm somewhat reluctant sicne they are so expensive and different from other hubs. Don't find anything about how they hold up in trail/enduro usage…
@ttengineer4049 ай бұрын
@@haentz Ive seen some stuff on vespers having flex with heavy or strong riders, but the classic is supposed to be amazingly gtg, its just heavy.
@EdBraunbeck3 ай бұрын
Reynolds with Hydra hubs was quick to replace my axle with the new design. It lasted +1,700 miles of moderate abuse on my Pivot Shuttle SL.
@garypark7459 ай бұрын
I used to run Chris King hubs which are great but very expensive. I now run DT Swiss 350 hubs and love 'em!
@bobtraweek30879 ай бұрын
One of the first very valid points you made was to maintain and check your equipment. 2720 miles on new Pivot 429 since March riding around Phoenix, Tucson, S New Mexico, Angel Fire and around El Paso, Tx. regular cleaning and maintenance every couple weeks. Rolls fast and smooth bearings still quiet. So when should my sub standard hub break as predicted by some commenters?
@hardtruth6039 ай бұрын
Great video, thanks for posting. When these came out I was sceptical, no one's done a good hub with single pawl engagement before for good reason, also was never really impressed with their previous hubs, always found bearing life not good if you lived someplace where if you didn't ride when it rained, life was short lived. I'll stick to my Hope hubs thanks, can get a complete set for less than you'd pay for a rear i9 or CK and they've lasted me really long, Hope supports their products way down the line too.
@I_am_Warthog9 ай бұрын
I had a bike stolen about 3 months ago, and the worst part of that was losing the 22 year old Chris King hubs that were on it.
@mrvwbug44239 ай бұрын
As a heavier rider who likes to get a bit sendy, this definitely has me wanting to stick with DT Swiss hubs, the 54t star ratchet is plenty of engagement for me
@andykrull92979 ай бұрын
The 54T star ratchets shear more easily, so keep spares for that…. Only solution is to buy CK I guess.
@ivanteo197310 ай бұрын
it's a failed engineering, or simply, engineered to fail. Solution: first change to DW Swiss and ride.
@treimar9 ай бұрын
Honestly DT Swiss is all you need for human powered bikes imo. On e-bikes you might want more poe.
@ivanteo19739 ай бұрын
@@treimar Reliable and durable hub is what you need, trust me.
@treimar9 ай бұрын
@@ivanteo1973 Yes, but as ebikes/gearbox bikes have a freewheel mechanism in the front aswell it kinda multiplies the engagement slop of the hub. So I do prefer high engagement for those. But I just recently settled for Hope Pro 5 with "only" 108 poe. Does the trick for me.
@aleksarajkovic34719 ай бұрын
@@treimarthat is reversed logic, for e bikes you need less poe, something like 18t ratchet
@treimar9 ай бұрын
@@aleksarajkovic3471 I get why you would want that for strenght and etc, but you will end up with slop fest. The motor has a sloppy freewheel and then you have a sloppy freewheel at the back aswell. It will take 3 business days to start moving. I prefer high poe to cancel out the slop of the motor as much as possible myself.
@SimonHarlow9 ай бұрын
Kind of nice to see a video that does not contain a load of swearing about bike products. Not by a 5 year old. Thanks.
@WheelworksHandcraftedWheels9 ай бұрын
The pen...is...working 😅
@symmetricon19829 ай бұрын
Interesting stuff. Glad I went with Onyx.
@fifthcircle19 ай бұрын
Same! Love my silent, instant, and most importantly purple onyx!
@cosinus_square10 ай бұрын
or a Ti axle, yes they are available
@forestkan66539 ай бұрын
Crazy. Back when I owned a hydra, I thought it was the coolest thing. Screaming down the trail, instant engagement, all that. I then snapped an axle within the year. Pretty soon I got sick of the whining sound. My next bike came with 350s, which I love aside from the fact that they don’t come default with a 54T. Echoing what other people have said, it is good to understand why my axle failed. I couldn’t figure it out and kinda just gave up.
@FSR20076 ай бұрын
I had similar snapped hubs in my hunt race aero wides, always between the freehub and wheel shell! They definitely creaked too, good to know, Hunt replaced these for free but wouldn't help me when I asked for the cause or what i could do to prevent it.
@danjelvantijnintellijel7569 ай бұрын
Pinner Machine Shop in Whistler BC offers Steel and Titanium i9 Hydra compatible axles as another possible solution
@Chalshus9 ай бұрын
Great video. I would like to not break my hubs. Thats why I only use 72 engagement points. ;)
@scottwerner6099 ай бұрын
This is great but unfortunate info. That said I do like I9 as a company and own 2 wheelsets with Hydras and 2 with Torch. It seems it would better to design this with to have two opposing pawls engaging without flex and therefore have half the POE at 345, which would still be great.
@martinschwartz73429 ай бұрын
I must be extremely lucky. I have a Hydra hub on my Kenevo SL e-bike. I weigh 290 pounds. In 4,000 miles I have had the hub once serviced. I have had zero problems.
@hardmtnbiker9 ай бұрын
Great information! I would expect a single speed hardtail but don’t use Industry Nine hubs. I have Hadley,Hope SS/T and Onyx Classic single speed specific hubs. New had an axle failure and have only replaced bearings on my Hadley hubs but original bearings in my Hope and Onyx hubs
@_ben_sweet9 ай бұрын
Never had issues with the axles, however I’ve had the freehub strip itself once before, which was not so ideal. Other than that one issue, loved the hubs
@Rallef799 ай бұрын
DT Swiss --> Money saved, problem solved!
@NoBrakes239 ай бұрын
DT Swiss and Onyx owners feeling mighty superior right now...
@oeifjoasef5 ай бұрын
I bought a set of wheels with the Hydra hub in July 2022. The rear hub had the old axle and failed about a year later. Industry 9 sent me the improved designed axle with new bearings. Now less than a year later 2 of the bearings are completely shot. The axle seem fine but to have to replacing bearing this frequently seem like this design is still problematic.
@zoranpl9 ай бұрын
Maybe titanium axle...light and it doesn't crack like aluminum ,its more elastic,flexible..or maybe inox as a cheaper option
@catherinemacalisang57829 ай бұрын
This is the reason why other hubs uses special inner diameter bearings (ex. 6902-2rs 16). Which means the inner diameter is 16mm instead of 15mm to thicken the axle a bit. That is also why THRU AXLE is far better than QR.
@WheelworksHandcraftedWheels9 ай бұрын
A 6902 bearing is 15x28x7mm and the 2rs means a rubber seal on both sides. 16mm is very rare bearing internal diameter and much more likely to be 17mm which is used in some of the Hope, Berd, and newer DT Swiss Hybrid hubs ~Tristan
@adoonjackson26059 ай бұрын
Stoked you guys made a video on this. Curious if you’ve seen the aftermarket steel axle from pinner machine shop. I broke 3 hydra axles in the first year or so of having it but ever since installing that thing the hubs been problem free for months. Theres been no problems with the pockets wearing either, I guess like you said since steel has more flex.
@thel1zardking10 ай бұрын
I’m curious how the sprag clutch from Onyx fairs by comparison? A completely different approach to ultra-high engagement.
@uldi1s10 ай бұрын
No issue, as the sprags on an Onyx all work at the same time, making the forces all even from all angles
@WheelworksHandcraftedWheels10 ай бұрын
We're asked about this comparison a lot since both hubs have fast engagement but go about it in totally different ways. I'll see if we can do a video on it! -TT
@Ali_Clarkson9 ай бұрын
no comment on reliability as I've not tried a sprag hub for years but they do have different feelings when riding. Firstly there's the weight...sprag hubs need a lot of steel to cope with the forces so they always weigh quite a lot compared with a pawl style hub. They also have a slight spongy feel when engaging...again it's been a while since I used one (and have never used an Onyx), it's not the worst thing but it wasn't something I liked very much. I will give them credit for being nice and quiet though, I do like that!
@WheelworksHandcraftedWheels9 ай бұрын
@Ali_Clarkson did you ride with the old Shimano Silent Clutch hubs? The Onyx has a similar spongy feel to those - personally I really didn't like it for trials but it never bothered me on a mountain bike. -Tristan
@scrappy75719 ай бұрын
I have a 2017 Torch hub. Eats the cluster shell bearings, lasts about 1 year. Love the quick engagement hate the reliability. Seems not much improved with the Hydra.
@robertkoleczko39879 ай бұрын
As a Bike mechanic, a hobby DH BIKE PARK HOBBY rider, and since I'm 12 years old I started MTB in 1992, I have one or two opinions about hubs and your video message. You want to ride your bike, without technical defekts? 1 - Don't buy Shimano hubs! XTR are to expensive, XT breaks apart after 6 to 12 Mon, Saint works but the bearings are bad!! 2 - Don't buy stuff, Wich axles are breaking and somebody on KZbin explains, why should buy it any way 3 - Go and buy some DT Swiss hubs, done 😜🤣👍‼️
@andrevoz98199 ай бұрын
I'm not an engineer, can I9 redesign the hub to have 2 opposite facing pawls or 3 pawls engage at once (rather than 1 pawl) and then have the remaining pawls engage shortly after to reduce the stress on the single pawl leading to the axle stress and bearing damage?
@erikhortsch9 ай бұрын
I've gotten lucky I guess. I have some Hydra wheels with like 4 seasons on them, and I'm 230 lbs and haven't had any of these problems yet on my FS bike. Just got some more Hydra hubs to put on a dirt jumper, we'll see if that could introduce enough stress but I bet it's better off than my FS bike.
@ChazNosloc9 ай бұрын
Great info, thanks for sharing.
@wiseoldman58419 ай бұрын
Have a set of 1970s phil wood hubs that still roll like perpetual motion. New always isn't better.
@WheelworksHandcraftedWheels9 ай бұрын
unless you want to install an XDR cassette ;-) Those old Phil hubs are amazing. -Tristan
@SnootchieBootchies279 ай бұрын
The average rider does not need that much engagement. For trials I can see wanting very quick engagement, but for mountain biking, it's really unnecessary. I just got myself the e-bike version of the pro5 for this reason. I want as many pawls engaged as possible because I just want the hub to last as long as possible.
@herethere25189 ай бұрын
Would love to hear your thoughts about Onyx hubs and their sprag freehub design. Probably the most instantaneous engagement out there and they've been doing it a long time; any known issues/downsides?
@WheelworksHandcraftedWheels9 ай бұрын
We've been asked this a lot since both hubs have similar fast engagement but go about it in different ways. We see a few broken axle issues on Onyx hubs which are ridden really hard, but nothing worryingly high. Overall they work well, but they are heavy (there's that trade-off again 😬) -Tristan
@buckcram59089 ай бұрын
would love to see similar analysis of zipp zr1 hubs!
@yetidh9 ай бұрын
What kind of service intervals would you recommend? For heavy use (heavy rider, big travel) to light use (light rider, hardtail)
@ridesafealways49299 ай бұрын
Very informative video. Can you do one for the Raceface Vault and it's reverse pawl system? Thanks
@Some_D0nkus6 күн бұрын
I have seen no hubs fail as much as industry nine. Probably 5-6 catastrophic failures in the past 8 years. I have seen the hub flanges crack free of the hub body, ratchet rings cracking and getting stuck, pawl springs cracking and of course, axle failures. I would love for these hubs to be strong but the reality is, they are not.
@tommyr959 ай бұрын
Good info, thanks! Any thoughts on the Onyx sprag clutch hubs? Would like to see a pros/cons list on the Vesper.
@kenh60969 ай бұрын
thank you
@berberger4814Ай бұрын
1:20 at this point you do a undercut (din 509), radius of 0.3mm should be enough to make it a lot stronger - I wonder why this is not done properly, if I understand this correctly, this gets educated in the first semester of mechanical engineering studies - I learned it in a side thingy in electrical engineering, so I am not 100% sure, but I really think that these are mistakes on basic levels I really rather use DT Swiss hubs were you know that they get these things right anyways, because othervise nobody would use their parts as oem parts
@WheelworksHandcraftedWheelsАй бұрын
The new Industry Nine Solix hubs have a very generous radius on that part of the axle...looks larger than 0.3mm to my eye but I don't any way of accurately measuring that. Interesting they went that direction on the Solix rather than the 'stress riser kit' on the Hydra -Tristan
@COOLBIKEyt10 ай бұрын
Thanks for this video, that's why I chose the 1/1 version and I have no problems. Now I'm considering ERASE hubs with 60 POE RATCHET for my new E-bike, have you had any experience with them?
@WheelworksHandcraftedWheels10 ай бұрын
The Erase stuff looks interesting but I haven't seen any in real life yet -Tristan
@COOLBIKEyt10 ай бұрын
@@WheelworksHandcraftedWheels In that case, I hope that this will change soon ;), because I haven't found many opinions about them.
@ionicman19 ай бұрын
Still keep an eye on the 1/1. I've broken my 1/1 axle several times (breaks in the same spot shown in this video), tends to happen to me about every 2000 miles. I ended up buying a 'forever' steel axle from Pinner Machine shop and it has been great.
@COOLBIKEyt9 ай бұрын
@@ionicman1 Thanks for tip ;)
@Acill9 ай бұрын
Wow, my i9 hydra hubs I thought are amazing. This makes me pretty nervous now.
@WheelworksHandcraftedWheels9 ай бұрын
They're good hubs with a really unique engagement system and sound - this vid is to explain how/why they work and point out the bits that need extra attention -Tristan
@mesere79 ай бұрын
when reality destroys marketing bs, this hub has only one pawl engaged vs dt swiss 240 has a 36 or 54 ratchet and they all engage at the same time distributing the load, guess how many broken axels and bearings did i have over the last 9 years? none
@shmulikklapwald98849 ай бұрын
A Titanium axle would solve the issue for sure, it'll have an impact on the cost for sure. With clever design it'll not have a weight penalty.
@mleavitt7879 ай бұрын
Danny Macaskill and all those other trials guys run Hydra hubs and put insane amounts of force through them, yet they still hold up. I wonder if this is because they are using super stiff trials frames.
@markifi9 ай бұрын
points of engagement
@thescerigai10 ай бұрын
great vid
@3sixty_sports9 ай бұрын
As the NZ Distributor of Industry Nine, we've seen nothing but great support from Industry Nine around this topic. Additionally, we can confirm we have had no reported breakages of the new axle here in New Zealand (over the last 12+ months) and bearing wear has also reduced. We must stress that this doesn't remove the need to maintain your hubs - they need care like any other part on your bike. One thing we'd like to add to Tristan's very informative video is the real world benefits of the Industry Nine Hydra. High-engagement rear hubs, distinguishable by their unique sound, provide nearly instantaneous power transfer to the rear wheel. Their benefits across various riding contexts cannot be understated. These hubs effectively eliminate the 'lag' typically experienced at the beginning of a pedal stroke with lower engagement hubs. This feature is particularly beneficial in challenging uphill sections or powering out of a berm. Moreover, they ensure immediate power application when you resume pedaling after backpedaling or freewheeling. In such situations, this instantaneous power transfer can indeed be a game-changer. If any viewers need more info on how to maintain the Hydra system or require service parts (bearing replacements or axle upgrades etc) do not hesitate to get in touch with Wheelworks. As one of our dealers, Tristan has good working knowledge of I9 Hubs and access to all the necessary components to keep your Hydras running sweet for years to come. Bruce Founder | Owner 3Sixty Sports
@WheelworksHandcraftedWheels9 ай бұрын
Thanks Bruce. The support we've had from your team and I9 has been nothing short of fantastic. ~Tristan
@3clubforever9 ай бұрын
Maybe a titanium axle would help it last long and still have the flex needed
@galenkehler9 ай бұрын
That's what I thought too.
@galenkehler9 ай бұрын
I think the bushing or sleeve would be better. A stiffer axle, but include a flexible section at the location where flex is required
@B_COOPER6 ай бұрын
If it wasn’t took free it probably would be a lot stronger of a hub. Axles on a time ticking bomb doesn’t sound very appealing
@Rose_Butterfly989 ай бұрын
Does the rear triangle flex based on pivot wear? My bikes all have supports that link the 2 sides together. On my trail bike, the rear triangle is 1 piece mounted to the linkages, I can't put a 29 in the rear because the bridge goes around the wheel, would worn pivots still cause flex?
@mcveyj9 ай бұрын
Great video. What's your take on Onyx's Sprag Clutch mechanism? Do you think this system is more robust and will require less frequent servicing? Or will high/instant engagement always have its downsides?
@WheelworksHandcraftedWheels9 ай бұрын
We honestly haven't built/sold enough Onyx hubs to gather enough info on their durability. We've seen a few broken axles when used by super aggressive riders, and we've seen the occasional freehub issue, but as I said it's not from a large enough pool that I can confidently point out the strengths and weakpoints of the hubs. The Onyx design is super unique and it would be great to do a deep-dive into how it works, but without having a sufficient number of hubs being sold don't expect a pros/cons vid from us any time soon ~Tristan
@paulbernard23979 ай бұрын
Maybe people should stop being obsessed with having the latest, greatest shiny bauble continually? Not entirely sure that an ìmprovement´ like 690 poe is necessary for anyone. Maybe we could all relax about whose hub is loudest, unless you are 8, and then it´s very important. Just go out and ride your bike.
@TryboBike10 ай бұрын
It is a quad bearing design with an axle overhang due to the freehub space. It is essentially a screw-on freewheel and is designed to fail. Hydra's reliance on flex is kinda/sorta admission to that and creative usage of the flex to get more POE. I9 old hubs - pre Torch series - were actually much better with wide bearing stance, but didn't have the fancy 690POE ( "just" 120 ).
@WheelworksHandcraftedWheels10 ай бұрын
The bearing placement on the Hydra isn't significantly different to any other modern hub -Tristan
@TryboBike9 ай бұрын
@@WheelworksHandcraftedWheels Yes. And just about any modern hub fails in just about the same manner, monst of the time, at least. I'm guessing that Hydra's increased incidence of breakage is, as you say, using this flex for engagement. However, I think that on full suspension bikes the issue is that chain growth is yanking the instant-engagement hub. Modern FS bikes are plenty of stiff, especially short link suspensions. I wonder if incidence of hydra's exploding is less on bikes with and idler suspension.
@petrstastny62810 ай бұрын
Thanks for great review. I’m thinking of Hydra not only because 690POE, but I also hope it will propery engage. My experience with other pawl based hubs is that after some time the powls does not properly engage and there is a click when you start to pedal. Any experience on this concerning the Hydra?
@WheelworksHandcraftedWheels10 ай бұрын
This isn't something we've had reported to us on the Hydra - they seem to engage consistently as long as the bearings are in good shape -TT
@aronsima34849 ай бұрын
I wonder what issue the Torch had ? Got new, never used old stock one a few months ago... that im yet to use. Except for the stupid design with O-rings and needing a special tool/ vise to remove the endcaps. Any other issue ?
@neozeonsolid9 ай бұрын
Love my bomb proof Chris Kings
@chp16409 ай бұрын
What about Tairin hubs? Steel, light and all points engaging…?
@Suspicious_Salamander9 ай бұрын
Forgive my ignorance, but does this just apply to hyrdra hubs or does it apply to all I9 hubs, to include 1/1 hubs? Great videos btw!!
@WheelworksHandcraftedWheels9 ай бұрын
Just the Hydra. The 1/1 is far more traditional and seems to go through bearings pretty quickly but doesn't have the axle breakage issues -Tristan
@jakobhp318010 ай бұрын
The "spokes"-man - really😂😂😂
@WheelworksHandcraftedWheels9 ай бұрын
:-D
@jaycarneygiants9 ай бұрын
Can't they just change the pawls design so that 2 pawls engage at 1st instead of 1?
@yologaming62249 ай бұрын
Why steel axle it design to flex like chromoly frame or getting a steel axle give more flex. how about getting 3 teeth per pawls so it support the load
@notsoenduro9 ай бұрын
How do you listen to creaking noises on the loudest part of the bike !
@johndef507510 ай бұрын
Axle flexing designed into the hub? Wtaf? DT for me.
@ssmtb10 ай бұрын
Great video! Is this an issue specific to I9s or could this also be an issue for other high engaging pawl based hubs ? (Like Project321) And could it be the case of different mechanisms such as Onyx Sprag Clutch?
@WheelworksHandcraftedWheels10 ай бұрын
Project321 Gen3 hubs use 6 pawls with 2 pawl engaging simultaneously...the way I've understood their design they are not using axle flex to allow a 3rd pawl to engage like the Hydra. The Onyx design is completely different and possibly warrants it's own vid as the two often get compared because of their quick engagement but the way they achieve this couldn't be more different -Tristan
@ssmtb9 ай бұрын
@@WheelworksHandcraftedWheels cheers, thanks for clarifying 👍
@sparky98649 ай бұрын
@@WheelworksHandcraftedWheelsI would really like to see a video on the onyx hub. Nice job on the video.
@MrSupermugen9 ай бұрын
Stick to the masters.. dtswiss.... Hope pro5 are very good aswell.
@swerv5129 ай бұрын
Glad I choose good old DTSwiss 240 hubs on my mtb😂
@Yoda-em5mt6 ай бұрын
Pitty i 9 dont make a steel hg freehub for riders with real power and torque .
@Christmylife784 ай бұрын
How about using a Pinner axle? Have you used them on your wheel builds?
@WheelworksHandcraftedWheels2 ай бұрын
No, we haven't used the Pinner axles. I worry about the super-stiff axle being really hard on freehub bodies. -Tristan