Is the DJI Mavic 3 Enterprise Accurate with Propeller and AeroPoints 2?

Propeller - www.propellera...
Aeropoints - www.propellera...
Emlid Reach RS3 - store.emlid.co...
Commercial UAV Expo - invt.io/1lxbx9...
Promote your Exhibit Booth - rami.promo/
📢 Join The Survey School: thesurveyschoo...
Visit The Survey School for resources to elevate your surveying career. Join our school to access courses, premium content, and a supportive community of professionals.
👤 Meet the Surveyor:
Hi there! My name is Rami Tamimi and I am a passionate surveyor and geodetic engineer. With over 10 years of experience in the land development industry, I have a wealth of knowledge to share. That's why I started my own KZbin channel, educating others about the surveying and geospatial industry and showcasing exciting new technologies. Follow along as I share my expertise and keep up with the latest innovations in my field.
#Aeropoints #photogrammetry #dronesurveying
Join this channel to get access to perks:
/ @ramitamimi

[@pwshepard]

This is our daily routine flying 4 Mavic 3Es and 1 Wingtra using Aeropoints and Propeller to process. We run local coordinates with our Machine Control. We only use our Rover to establish a “known coordinate”, then place an aeropoint on it each flight. We never have to break out a rover unless our point is destroyed. We fly anywhere from 2-6 sites a day, so this is huge time saver. Excellent video showing the process and accuracy between the two systems.

[@travislawrence4679]

I used to be a drone surveyor for a local aggregates company and we used the Propeller's AeroPoints and processing system. I loved it, for the most part (the 3D models could have been a little better, but it wasn't necessary for the tasks). That system has so much more than what was gone over. It was perfect for those quarries out in the middle of nowhere. Though really, really expensive, I cannot recommend this system enough for those needing a robust collection and processing system.

[@nojusticenopeace8717]

Thanks again mate you are very good teacher, can you please tell me if you have to connect your DJi RTK module to your Emilid base station?? Once you have completed the drone set mission and mentioned that you had RTK on in your drone!

[@scottkarlins]

Just an FYI - The Aeropoints will use the Center-Bottom of the Aeropoint as it's location. Since you took a shot using the Emlid at the top of the Aeropoint, that would be a 26mm offset. So your measurements from the Emlid are actually even more accurate!

[@RamiTamimi]

That explains why when we use the propeller correction network all three of the points were 0.1 feet higher. Thanks for the insight.

[@RorySanMiguel]

@@RamiTamimi OMG Rami how did you get this wrong 🤣

[@tszabon]

This is soo cool :) Thanks for another interesting video!

[@MarkTheRealtor]

So interesting Rami. Watched it twice.

[@monaakkila9891]

As usual great work 👍

[@volantdrone]

Question, I noticed that you aren’t using the Lora radio. Given that your workflow is all PPK, couldn’t you also check your points with RTK just to compare RTK vs PPK to check your points since propeller is already using PPK.

[@adlep]

Rami: I'd put an additional large number sticker on your APs to have easier time identifying them on your photos..

[@Chief.Surveyor.AliQassim]

Great Job ............thanks

[@moonmullins8227]

Does the Mavic 3 have built in RFID?

[@sakiralikhan5092]

I am planning to buy if possible please review it

[@sakiralikhan5092]

Sir Please review #Setlab Android Total Station SLT12 model

[@jaysom2240]

Waste of money. I do however like their browser based data viewing after the flight. I just dont see the point of them when you already have a rover. You are better off going and shooting your own GCPS. Not worth the 13k a year subscription in my opinion.

[@scottkarlins]

Agreed! Aeropoints are nice and they work great. But, just get an Emlid RX or RS2, and the Emlid pole (a great portable 1.8meter pole!) and use disposable Aerotas paper targets. Then there is no need to go back and collect the targets. Time is money!