Replacing Driveshaft Center Support BEARING - Peugeot 307

Video showing the replacement of Driveshaft Center Support BEARING including CV Axle removal and re-installation in Peugeot 307 SW (2005) 1.6 v16 petrol engine.
LINKS:
• Changing Transmission ... (Changing Transmission Oil)
• Transmission Output Sh... (Transmission Output Shaft SEAL Replacement)
Hope it helps.
Music by Is It Fixed Yet

[@joseboquitasdelacoronilla7648]

I was looking all over the net to find a video about how to remove this particular bearing, Thank you much for posting this video is of great help... keep up the good work.

[@westfielder01]

Used this as a guide for my 2010 Berlingo B9 - it's the same shafts and almost exactly the same process. You can change both shafts without undoing the drop links, track rod ends or bottom ball joint. Took 45 minutes for tge long shaft and 30 for the short one. Thanks very much for the video.

[@toyota218921]

Just what I needed to know for my citroen relay. Thanks

[@michaelflanagan7713]

Thanks. Gave me the courage to do it.

[@ryadhkebaili1900]

Thank you for the video i have remplace tous bearing yesterday good job

[@isitfixedyet891]

Congratulations and thanks! :)

[@karma-pe7gw]

Excellent video

[@danielalejandroparedes8749]

x fin un video mostrando el desmonte de la pieza

[@danielalejandroparedes8749]

good

[@combomaster99]

After 18years the bearing is rusted shut AF😂 i was wondering how other people might have removed it but i guess brute force is what's best. Nice vid

[@tabor58]

Capooooo, bien ahí, me sirvió a la perfección, excelente explicación, saludo desde argentina, like y me suscribo ❤

[@danieloalbertolopez892]

Gracias ...desde BUENOS AIRES ARGENTINA

[@spencermm3681]

Grscias por compartir , me sirvió mucho. Slds

[@matthewjenkins1161]

Well done though I have a few comments that may help others. That driveshaft is the same on right hand drive cars. At the beginning you said the gearbox is on the left, because the steering wheel is on the left. Not so. Gearbox is on the left in all FWD Peugeots. I think the job is easier if the pop the lower and track rod balljoints, though appreciate that can be dictated by the tools available. Hitting the bare end of the driveshaft with a hammer can round the threads, making reassembly near impossible. If you must strike the driveshaft end with a hammer, have a spare lose nut on the end of it to protect end threads. Brand new driveshafts including that bearing, both CVs and the gaitors can be had for £40 delivered. At that price it is highly questionable if it is woth just changing the bearing. Didn't mean that to sound critical. You got the job done and just added these thoughts to help others.

[@isitfixedyet891]

Hi Matthew, Great to see you commented. I like the comments a lot! Good to see people share the knowledge :) Have a great day and thanks for supporting the channel! Cheers

[@buchhalterkimbo6934]

40 bucks sounds cheap! I bet the driveshafts quality is also as cheap as the price.

[@forevermec]

thanks bro

[@aminr.3775]

Thank you

[@ricardorodriguezmandoza2352]

Gracias por tus vídeos, son muy explicativos...

[@isitfixedyet891]

De nada mi amigo!

[@jacquesleroux530]

​@@isitfixedyet891can you please give me the number of the bearing i struggle to find this bearing for the cv jiont support please and seal number for the gearbox

[@chandantiwari6386]

Thanks bro

[@hzmusallatt]

Hi thank you for video l have Citroën grand Picasso when watch this video l check my car right and left drive shaft today they are moving in ( to gearbox ) out ( to wheel ) coming clicking noise it is normal.? No any leaking or broken part just2 -3mm rocking right and left.

[@m2kuteip]

The gearbox seals are very fragile on Peugeot cars throughout the years. Even if the half-axle only slips a little bit out, the lip on the seal is broken and you pretty much always get a leak. I learned that the hard way on my first encounter with french cars and never forgot about that. And also the seal costs almost nothing and is easy to replace... Also lot of lubricant should be applied, it really helps a lot. but i got some good info on the peugeot intermediate bearing (i have a 206 that needs one now... ) Cheers! :)

[@ParFektion]

What kind of lubricant? 🤔

[@dbs5212]

​@@ParFektionjust clean oil

[@SamHocking]

Think it might be model-specific, ive not had to replace the seals on 406 or 407s and removed the drive shafts a few times through owning the cars and not needed to be be replaced. If you're just pulling axle straight out and pushing straight in it shouldn't damage the seal at all.

[@malkie638]

bicycle tubing is what i planned to use too

[@evertstensholm5184]

Nice video, but I can't find anything on Berlingo. My question is: Is'nt this exactely the same driveshaft setup as Berlingo 2010 75hk 9HTDV6BTED4?

[@kunj035]

Hi, What was the problem in the car that led you to change this bearing? Was theer any kind of noise while driving you heard or something?

[@ylmazgunduz1840]

Pejo 307 1.6 sw makes a lot of noise in 2005 model gears, could it be related?

[@Blurredman]

My right hand side Peugeot 205 driveshaft does not seat fully- not sure why this could be.

[@bjornnylander8754]

Did the bearing make any noise while driving?.... ive got a whining noise, same type of sound a bad wheel bearing makes, allthough the wheel bearing is ok. ?

[@rockyfish3115]

I got a 36mm for the wheel bearing Nutt but it's a 35mm on mine

[@ernestoleiva7747]

Hi, thanks for sharing this video, what are the symptoms to determine that the bearing needs replacement?

[@nicolastremblay7527]

vibration on high speed and cv axle hard to turn by hand

[@davidkiss9061]

Hangot is adhat??

[@marcioatosbuscariolo1734]

Ok❤

[@AzizAkbiyik]

6:47 What is the size of these pins and nuts 11mm or 12mm? Thanks for your sharing, greetings from Turkey 🇹🇷

[@gtline9943]

for me is 11 /

[@TARIQQ-DIY]

Where can i get the official guidelines for tightening peugeot 301 nuts?

[@AJ-zv9tn]

Give phone call with prugeot

[@mateuszgarncarz3184]

Jakie były objawy?

[@saifqased6458]

شرح جيد جدا

[@eksine]

Beer ring

[@charlesbenoitthomad]

Wheel alignment needed after?????? Lmk

[@nicolastremblay7527]

no

[@thomasoreilly1105]

whats the dimensions on the bearing ? please help im stuck

[@isitfixedyet891]

Depends on your car model Thomas. Read the VIN number of your car and call the parts dealer. They will tell you precisely what you need.

[@newname8571]

The right key size is not 36 mm but 35mm😉.Very rare.You can buy it from Bezos.

[@ionutstefan8835]

You are from Romania???

[@isitfixedyet891]

Hi, Nope but have some really nice Romanian friends :) Cheers!

[@javieevasquez758]

hola bendiciones Este problema lo tengo en mi Peugeot 206 La verdad no entiendo inglés pero me gustaría q me lo pudieras traducir en español

[@rockyfish3115]

Should of undone the lower control arm

[@wano87tt]

Вот только молотком стучать по резьбе не стоит!

[@matiz33]

What is beering? I think you are talking about a bearing 😉

[@tanglewood777]

yea a bit home made wood going to take weight car ahaaaaaa

[@martinprice6162]

34mm socket nearly all Peugeots and citroens

[@darmatles]

Polakowi wszystko z piwem się kojarzy. Łożysko po angielsku brzmi berin a nie birin :)

[@isitfixedyet891]

Robie co moge ;)

[@barteksz8419]

Polakowi nigdy nic nie pasuje :) chłop zrobił zajebisty poradnik ale zawsze znajdzie się Polak któremu coś nie pasuje, zamiast się cieszyć że jest poradnik ok

[@Yabba0408]

Doo doo doo doo, duggu duggu duggu duggu duggu duggu etc.

[@phildatkom4248]

hahahahahaaa turn your fucking wheels to easy remove that axle drive...

[@jackripper1134]

What are the simphtoms of this bearing. How should i know its bad?

[@buchhalterkimbo6934]

some noise while driving.

[@jaymann]

And vibration.

[@buchhalterkimbo6934]

@@jaymann you know if Ford / Peugeot do have special tools for replacing that bearing? On our 2005 Focus C-Max I have to replace that bearing pretty soon.