THE HANDBRAKE RETURN SPRING IS MISSING IN THE VIDEO!

Thanks

did you even try a puller?

Sunt utile și in 2024 videoclipurile tale !!! Păcat ca l-ai făcut noaptea !! Multumesc !!

Thanks! This video helped me to understand how to access quickly those Maxi fuses (just two plastic clips holding the complete assembly).

Thanks ✨

Helpful! Thanks

Thanks for the video. Do you think I could replace those sensors myself? I don't have lifting tool.

What size is the nut on the oil tray ?

Couldn't u pop the bottom ball joint , to remove the driveshaft 😂, easier... done mine like this.. New driveshaft.. Good video...

Is this 1.6 petrol 109hp?

Nicely done sir.

What a bucket of shit 😮😢

Just bought a 307 and very handy to know before hand ... thank you!

Good video. Thanks a lot!! I have a 206 1.4i and I went crazy trying to get out the crankcase. This way is easier. (Especially if you have a guide)

Very good. No background music nice clear voice. Well done. But you need a special tool to both rotate and compress the brake piston at the same time to make it go back in. Many cars allow direct compression of the piston but not Peugeots.

Nut size is 35 mate

I'm driving this Peugeot for 8 years now, anytime I need to do something I come back to your channel. Thank you

Obrigado amigo, você é um amigo

Ми дякую вам ❤

Good Video!

Thanks - you've solved me a mystery - I suppose if the first one lasted 20 years, replacing the whole assembly with a new one isn't a bad investment

Thx for showing

Thx

thank you very much.

Hi, is this the same on 307 2.0 petrol serpentine belt? thanks

Safe my money 🤑🎉

Well explained and carried out. i have just fitted a new clutch on my peugeot 306 but i couldnt release the centre bearing it had siezed solid, a common problem on these . had to release the carier bracket and pull it out from the back of the engine, total nightmare.

36

Rather than do this I would buy a whole new drive shaft. You get new joints and boots and a warranty. Complete shafts are not that expensive and they are so much easier to remove as a whole and then replace. Saves so much time and faffing.

Don't be lazy... if your going to make a video you need to do sufficient research beforehand... a fuel hose/line is not a "fuel cable", cable is made up of various strands of wire!!!

According to servicebox, the way to adjust the rear hatch is apperantly to loosen the screws on the door hinge, the 2x screws on the left / Right, tho truth be told, its like " oh yeah... loosten theese screws.... then tigthen them to 9 Nm " thanks peugeot, very helpful haha :) i need to try this method first tho, lets hope for the best.

Tnx for showing had the same problem. The fix of you did solve it. Thank you so much.

I did it exactly as shown in the video and I was able to remove the half-shaft joint after several days of unsuccessful attempts. Thank you very much for the idea and the video!

Where can i find mine? I have a 2.0ltr 16v. Plz help me

need to remove my top light cause there is a small spider in it!

Merci de France 😄

Couldn't have done it without this video - huge help - big thanks 🙏🏼👍🎉

You made it wrongly you should make the teflon as a thread and screw it around the end of the plug.

P0500 trouble, fixed the left sensor but speedmonitor is still out of mine Peugeot 307 from the year 2004. Do I have a Gearbox sensor or just wheelsensors?

Thx😊

Great video and very helpful. Solved my problem. Thank you.

Donde esta el número del motor de este modelo hermano??

where is the ABS RELAY ? I am searching for years, cannot find it anywhere. The fuse was missing. Please help.

I dont know why you do this stuff but you've saved me so many euros and work doing this stuff. My Peogeot is in her last steps but still going.

Great video , thanks ! Can you make one aswell for how to replace or fix the hanging heat protectors from the back side of the engine that always fail and are hanging from the top like sheets ?

kool thanks👌😊👍

Did the bearing make any noise while driving?.... ive got a whining noise, same type of sound a bad wheel bearing makes, allthough the wheel bearing is ok. ?

What type of bolt is it? I dropped mine and cannot find it. I need to order a new one. I know its 8mm but don't know what type it is.

Thanks! I probably would have bought those cheap ones if I hadnt watched this before.