How To Make A 3D Wooden Christmas Tree /// Great Ideas For Christmas!

[@bradyoung7292]

Very Nice! I just built this myself, and here's what I was able to figure out between the video, other comments below and my actual build (U.S. / Imperial units and lumber dims): Used 1x2 for everything except vertical base (1x6) and top cone (2x2). Ripped 20deg sides on 1x2's with table saw, removing as little material as possible. bottom of tree is 16-3/4" wide (16" pieces) followed by two each 14", 12", 10", 8", 6", 4", 3" and than top cone - came out a bit wider and shorter than this video, but the 70deg sides line up near perfectly to the top. Hardest cuts are ends of 1x2's, need a compound miter saw set at 20deg on the base and 7.5deg on the bevel. Flip 1x2's after each cut (watch video closely) and lumber direction matters - you'll have to experiment. Again, very cool and thanks to I wooden for posting this!

[@iwooden2507]

good luck my friend

[@EliRibeiro-q2s]

olá, poderia me passar as medidas da arvore em centímetros, por gentileza ? gostaria de fazer para minha família

[@AllenOxendine]

Cool project, thanks for sharing

[@iwooden2507]

Thank for watching

[@laurentpfister2388]

Bravo et MAGNIFIQUE 👍👌

[@AllenOxendine]

Watching again, cool project

[@danmoreton1788]

Outstanding!

[@edcarbone241]

Beautiful Work!! And I like your 3 combo saw!!

[@iwooden2507]

Oh it's very good. 👍

[@lisaschultz5173]

I would sure like to be able to get the measurements for this tree!

[@donaldmaclean6238]

I built one. I made my stock 1 in thk with Parnell 20deg. Cuts on side. Large rectangle on bottom I made 14 in Long on top side. End angles are 20 deg as well. Made 14,12,10,8,6,4. Rectangles. 2 of each. Top I cut at 20 deg to make the point.

[@susandavis257]

Hardshell Woodworks does.

[@lindsaylavallee5012]

Well done … it’s beautiful !!

[@iwooden2507]

Thank my friend

[@lidianelida9629]

Excelente trabajo, felicitaciones!!

[@iwooden2507]

Thank for watching

[@rajrooplal7595]

Fantastic, I love it

[@iwooden2507]

Thank you so much

[@noeldeweese4975]

Very nice build. Very original.

[@iwooden2507]

Thank for watching

[@sneakyhippo8663]

This is awesome and has potential for so much more. Thank you for a wonderful video and the inspiration! You did good work my friend!

[@iwooden2507]

Thank for comment

[@BrianF.1969]

Very nice! I will be building a couple of these soon. Thanks for the video.

[@iwooden2507]

thank for watching

[@iwooden2507]

Good luck my friend

[@dorothylehman4164]

Great job it's beautiful you did a wonderful job

[@iwooden2507]

thank you so much 😊

[@pathardage1880]

Outstanding. Very innovative. Thank you.

[@iwooden2507]

thank you so much

[@iwooden2507]

God bless you

[@dandagaiola4750]

Excelente trabalho ficou muito legal que Deus continue abençoando você e toda sua família amém 👪 👪 👪 👪

[@iwooden2507]

Thank you so much

[@quietspacearts]

love what you made here, maybe to stop wood falling to ground have a chair or hobby hors to rest the end of wood once almost through the saw that way you not have to bend yourself or damage the wood x keep on making x Vanessa

[@iwooden2507]

Thank for comment!

[@NarsiMan88]

Nice ❤❤❤

[@davidfleming1395]

Well done son merry Christmas nice video from Wales UK 😊

[@iwooden2507]

Thank you so much 😊

[@marlenegregory5853]

Very beautiful!

[@RamoneZuniga]

I would like to get plans for this build ❤

[@chuckross3243]

Very nice!

[@Pe.Pe.]

Sehr schön geworden 👍👍👍👍

[@elizabeteoffredi1642]

Arrasou ! Lindo demais ! Parabéns !

[@wizpopr]

It would be great to know what the measurements are when cutting the pieces on the miter saw. And how many of each to cut.

[@IrwanSihombing-ng5bz]

Love it.. Wish I could make one for me

[@Ricks2Cents]

*Here is My Twist on Your Build!!! How did I Do?!?* *Making Wood Christmas Trees | 3D Geometric Christmas Tree | Step up Your Wood Working Game!!!* kzbin.info/www/bejne/hmaTfoWkr8p6mbs

[@iwooden2507]

oh It's was great 👍

[@Ricks2Cents]

@@iwooden2507 Thank You!!!

[@iwooden2507]

Merry christmas and happy new year!🎆

[@Ricks2Cents]

@@iwooden2507 Merry Christmas!!! Thank you for the Inspiration!!!

[@PLINKER]

super!

[@DIY-ART-D1R]

Sự hoàn hảo và mới mẻ cho ngày giáng sinh. Bạn thật tuyệt vời. Chúc bạn thành công

[@davidharnett5640]

This Christmas you should buy yourself some machine guards

[@Wagner-yw5dp]

Incrível seu trabalho!❤❤

[@MrTrecutter1]

Beautiful

[@iwooden2507]

thank for watching

[@emmanuellevargas7021]

it is a beautiful x-tree , it wokld be nice if he posted at least the angle of cutting ,and the high of the this trees .. nonetheless if we draw a x-tree on a big piece of cardboard the we want it ...from them we can get get the angle .....

[@sneakyhippo8663]

The angle that was shown is the only one used throughout the whole build for the top. 20° 4-2x4s were used. That completes the top. As far as the Stand, that is something you could make with your own design.

[@duane8363]

Hardshell woodworking. Has full build and instructions on how too.

[@colinfreel1312]

Is your mitre blade tipped? At what angle? Love the build.

[@alexreid4131]

Nice work! What finish are you applying at the end?

[@massimobrambati8973]

complimenti molto bello...bravissimo!

[@iwooden2507]

Thank you so much 😊

[@Chukavin]

Отлично!!! А у нас ёлки живые растут!!! Много!!!

[@ChalePousada-ig3hx]

Top muito top, vou fazer

[@DaltonHBrown]

There's something kind of...odd about building a fake tree out of wood. lol

[@MartinStone-ei6jx]

In what way? A real Christmas tree is made out of wood . 😊

[@DaltonHBrown]

@MartinStone-ei6jx lol, because it was already a tree. Like a Frankenstein's monster just made of wood.

[@jorgeluisborges5130]

Hola está muy bueno, quisiera las medidas que uso.

[@lancelowery3081]

This is beautiful and i would love to build it! Where can i get the plans?

[@aungmyat7242]

2:10 Fly something from your table saw.

[@magaleemoraes8408]

Que coisa mais linda, parabens

[@iwooden2507]

Thank you so much 😊

[@darrellbaker9184]

Thanks @bradyoung7292 I tried 7.5 ° on the bevel and 20° on the base I flipped each piece over however I always ended up with the inside joints having a gap and the outside joints the ends were proud off the sides. Is it possible that I started my first cut with the wrong edge against the fence? I had the 20° cut on the base so the top edge was tight against the fence. Wish I could figure it out. Any suggestions? Thanks.

[@alessandrofranca7525]

Belíssimo trabalho parabéns

[@iwooden2507]

thank for watching

[@gediminasmockevicius5994]

klasse - Litauen

[@rafaelmatos9377]

Le pones una bombilla que cambie de colores entonces si queda mas bonito❤

[@eliasleandro2218]

projeto perfeito.

[@iwooden2507]

thank you so much

[@Mukes4889]

Wow🔰

[@Zamboni-0805]

But why?

[@osvaldocogollo2648]

Excelente proyecto podríamos saber las medidas de las piezas bendiciones

[@johncortes4103]

Great job. Do you sell the plans?

[@BeaSahlfeld-lu3pm]

I'll buy a set of plans if you can make them up

[@junmiguelcarpenatorres7014]

Está muy bien pero... Antes de montarlo yo le doy una pasada de gasóleo a TODAS las piezas y lo dejo que se empape bien , después lo dejo secar y se barniza , en lugar de grapar se marca y se atornilla para poder desmontar

[@iwooden2507]

Thank for comment

[@euniaturnbull3112]

Wow beautiful I would like to know the measurements

[@SPMech1]

👍👍👍👍👍👍👏👏👏👏👏👏👏👏👏👏👏👏👍👍👍👍👍👍

[@esperanzaalegria1591]

Que medida tiene la primera basa? Gracias

[@iwooden2507]

45cm

[@Sinceretony]

Amazing 🫡

[@darrellbaker9184]

Was anyone able to figure out the dimensions? It's really nice I would like to make one

[@chrissmith-wq6gr]

Check the reply to the first comment.👍

[@victorapodaca679]

Wonderful. Do you have a cut list for this?

[@iwooden2507]

44,42,40,38,36,....,4

[@iwooden2507]

it also depends on the height of the wooden bar. I used 4 cm wood

[@victorapodaca679]

Thank you. Merry Christmas!

[@victorapodaca679]

I’m assuming your dimensions are cm.

[@ronlittle887]

Could I get the measurements, and the angles for this project?

[@YankeeDave75B2O]

From what I could see, the "table saw" aspect we well as the bevel, were on 20 degrees each. As far as the measurements, it seems that you could make it as big or small as you would like.

[@eugenemarais9520]

what is the measurements you made the tree with ?

[@john-u7r9f]

what are the measurements

[@john-u7r9f]

I really want to make this can you tell me the measurements

[@andyholland8773]

Is this classed as reverse engineering 🤔😂

[@marlenegregory5853]

Could you make me one?

[@adamgendreau6313]

Has anyone figured out the measurements?

[@muddslide8829]

Measurements for this project and angle cuts ?

[@27Brandis]

Do you have patterns for this tree for sale?

[@lawlessjff]

I guess it shows you how he built one, but he won’t tell you how to do it

[@bonniegiddis9636]

Are there patterns for this design?

[@osvaldocogollo2648]

Cuáles son los ángulos que se utilizan

[@iwooden2507]

I use a 70 degree angle

[@MaximilianoCabrera-jy3ct]

🤔👍💪🇦🇷🇦🇷🇦🇷

[@iwooden2507]

👏🏻👏🏻👏🏻❤️

[@iwooden2507]

watch my next videos please

[@randyhoudashelt1239]

A little commentary would be nice, for those of us who aren't mind readers.

[@RonRockhold]

❤m

[@iwooden2507]

👏🏻👏🏻👏🏻👍👍👍

[@garyperrin8172]

but you don't tell us how to make it no good

[@antonkranjec3575]

Why is he wearing a mask? Is he sick?

[@PapaFoxtrot2002]

How is that question relevant to the video? Are you being a COVID troll and unhealthy in the maturity department?

[@antonkranjec3575]

Its an honest question.

[@dhtango]

Dust. From the saw and sanding.

[@melissaguer7641]

Want sawdust in your lungs?