Jackson Lumber Harvester 3 Saw Vertical Edger

Using a 3 Saw Vertical Edger to cut cants. And a view of the push-button sertworks.

[@deksper]

That maladjustment of the Edger depths is criminal.

[@mtl-ss1538]

New Zealand has big logging trucks. Gross Masses of around 150-tonne. kzbin.info/www/bejne/j3q7oI2wm6d9gZI,kzbin.info/www/bejne/jKOoaWptitljpKs&ab_channel=WillBishopTrucksNewZealand kzbin.info/www/bejne/inq8dYmahJWnebM -kzbin.info/www/bejne/oKa4k5Kvorxmhrc&ab_channel=WoodleysNZ kzbin.info/www/bejne/rJ25pIqhatWEZs0 New Zealand- Classic Chip Trucking with 8V92TA-13sp.@ 40t kzbin.info/www/bejne/nV6ln6qvd7Bofs0 NZ farmers trees been logged,@57ton gross. kzbin.info/www/bejne/oJLOaKOOa9Z2n7c kzbin.info/www/bejne/rKvUlXqPoK1seZo&ab_channel=MahoeSawmills kzbin.info/www/bejne/nZune6imrdVmrdE&ab_channel=PetersonSawmills Largest Sawmill in NZ .>kzbin.info/www/bejne/n5bEZH-nh5hqnZY&ab_channel=RuralDelivery. kzbin.info/www/bejne/boPdfK2LaNysoc0&ab_channel=NZBuilder%2F%2FJoshChapman

[@diywood7290]

Wood cutting machine is very modern and professional, you have a great wooden workshop

[@vballchkmom2aa]

@MiscCheetah. As a rule of thumb, you are correct, but watch the video, Donkey has a point, some of the slight cuts that he is talking about, are more than slight, and are too deep to plane out. The 8x8 or whatever he is sawing has to go into some sort of gang saw system, and then the deep cuts will show there true colors. Most of the slight cuts wont hurt, but i did see a couple that would.

[@jamesiec61]

Impressive. High-speed work!

[@gettuff2]

Nice bit of kit!

[@dougsmith9099]

Need to set the guides edger saw marking the log on the carriage

[@TheWildWestMill]

There are no guides on the edger he his pushing the headsaw to hard and it’s running into the edger I run the same style setup

[@dougsmith9099]

​@@TheWildWestMillI know there's no guides on the edger I meant the head saw it's running out of the log, either that or dull

[@TheWildWestMill]

Yep you’re exactly right. That saw is getting dull. He’s pushing too hard or the guide pins aren’t where they should be

[@schattenmygirl]

Jackson Lumber could not be endorsing this video with the head saw running out. As for adjusting guides the saw should run true, the guides merely a fail safe (safety net). My first thought for running out as it seems to be doing is blade tension issues. B U T there are many factors to consider.Those would not be in sawyer 101.

[@OlMillwaukee15]

It's like a canter and a gang all in one. tail it with an edger and a trimmer and you could produce alot with 3 operators if you fixed that one flaw of your horrizontle saws and made it so they didnt cut deeper then 2 inch flitch

[@richardkruse9739]

Agree for sure i think I like a resaw straight done the rolls then back to the edger. feeding edger from both side then to drop off out the mill to trimmer and green chain

[@fletcher3913]

That sawyer is good.

[@dougsmith9099]

Needs to learn to set the guides

[@robertsutton5484]

The reason leaving edgar Mark s is saw running out love the mill been running one since 1994

[@sasolas23]

NIce saw : )

[@user-xm2qh3wg2u]

เลื่อยเก็บไว้

[@gdaruda]

That's a great mill what powers the head saw and edger, How much hp?

[@donkeymorris]

OK, I'm no expert, but aren't those edging saws leaving slight cuts in the bigger piece of lumber?

[@ron7187]

This is the initial rough cut lumber. That'll get planed down to the dimension that you get at the lumber yard.

[@TheWildWestMill]

The edger is leaving lines in the log cuz he’s pushing too hard and probably needs the sharpen. I run the same style setup and it will do that

[@robertsutton5484]

Sawyer dont give justice to mill slow

[@Ivansky1]

How much does this Job Pay?

[@MotoXXX7]

That thing makes some nasty cuts with the egders saws. The top edger saw is cutting WAY too deep and those will no way plane out.

[@Folkhero01]

He needs to stop and file his teeth immediately.

[@raymondcote6669]

Jackson harvester. Wanted to see slab cut off not the panel lit up!

[@raymondcote6669]

Show slabs coming off the blade

[@simohamdesimo672]

je sus intéressé par cette scie je veux plus de formation merci

[@user-xm2qh3wg2u]

ไม่ใช้ง่ายๆ

[@bowind1895]

L

[@raymondcote6669]

Do not need to see the control panel! Ever!