Neglected Troy-Bilt Snow Blower Basket Case - Will It Run?

[@MichaelHoersch]

Normally, I do not like super long videos but James is such a good instructor that I just can not get enough of his videos.

[@goodole1usa]

The only thing that is missing is that he uses some tools that are not easily identifiable. It would be nice if he could post the P/N or link to obtain them.

[@KaldekBoch]

As a motorcyclist in the 1960s, my Dad said he used to remove his chain every few weeks and just soak it in oil. Thank god for O-ring chains!

[@JohnSmith-yv6eq]

There used to be a large diameter shallow tin that contained grease/ You washed the chain in gasoline and cleaned it and dried it. Then you curled it up and placed it on top of the solid grease.. and put heat onto the bottom of the tin. a camping stove or the wife's electric stove in the kitchen when she was away... The grease melted and the chain submerged...every nook and cranny filled with lubricant. After 30 minutes you fished the chain out by the wire you had slipped through the last link and hung it up to drip dry back into the grease pan. Then the chain went back on the motorcycle...for however long it took until you felt it needed another dose.

[@mgabbard]

She went though that wet, heavy stuff like a champ! The proceedure was a success, doctor.

[@mwolrich]

you took that old, beat up snowblower from something most would have thrown away, to almost new condition.. I agree, the older machines were built much more solidly, its worth taking the time to do a full restoration, great job 👍

[@DeadKoby]

The snow king motor was LEGENDARY for being durable. The power equipment shop near my home surmises that my snowblower will rust to bits before the engine is worn out. My father purchased it 30 years ago... and other than oil changes/lubrication.... it's just kept going. Every season I pull it out THINKING it will finally need carb service... and the dang thing just starts and runs properly.

[@gadasavideos8564]

As long as oil level kept up

[@jcondon1]

I have a love hate relationship with Tecumseh's. But the 10hp Snow King has always been a great engine for a snow blower. Nothing that has followed can beat it.

[@DeadKoby]

@@jcondon1 I've had a few OLD OLD mowers (70's era) with super good Tecumsehs on them too... Some of the production /w/ the plastic carbs, and the lack of a governor arm spring would leave the motor hunting for the RPMs. The biggest problem we have now is the parts cannon for keeping these things alive.

[@jocbt]

I inherited an old 70's era Craftsman snow blower. It had a lot of rust on it and the muffler housing was rusting too so it was loud. The cou de gra came when one of the impeller blades broke off and made it unbalanced. It would still work but was like a paint can shaker. No parts were available and didn't have a welder handy so off it went to recycle center. I bought a Troy Built Storm King in its place and been working well for 4 seasons or so.

[@lestergillis8171]

​@@jcondon1I bought a MTD Yard Man unit from Northern Tool back in 1999. It has a 7hp Tecumish OHV version. The worst thing that has happened to it so far is: Rubber clutch disk needed to be replaced AND it goes through a pair of skid shoes every once-in-a-while. Since the time I bought a fairly capable MiG welder, (late 2010), I have just refurbished my old ones over. I also made a template on a piece of heavy craft paper so that I can now make the WHOLE SKID if need be😉. IF you cannot find a used replacement from your junk pile, I suggest making a replacement from bulk leftover sheet metal.

[@davidbohner692]

Thanks!

[@michaelclaflin]

You’ve got the skills to pay the bills. Nice job.!

[@DeadBrokeBBQ]

Talk about an addictive video that you just can't stop until it is finished!!! Fantastic job and I did learn something!!!!!!

[@petenelson8136]

Love watching how you do your analysis to figure out what's wrong with a machine. You made me wonder why I threw out my old snowblower, but I didn't know what I didn't know so ....

[@tiredoldmechanic1791]

My father had a Troy-Bilt blower. When the city put sidewalk in on his street he had to put a 3 foot high retaining wall because his lawn was higher than the sidewalk. The Troy-built never threw snow very well, especially heavy wet snow. The one you have there has a tool to clean out the chute. He was going to buy a new blower. We took it apart and changed the pulleys and belts to run the impeller faster. We also added an impeller modification kit that added pieces of belting to cut down the gap between the impeller and the housing. After doing that, the blower not only blew wet snow over ten feet high but also the melt water.

[@FirstWizardZorander]

Wow, that came out looking like new! Kudos for adding the model/serial labels. Refreshing to see such attention to detail! I'm a software engineer, and it brings me joy to see someone take pride in their work regardless of field

[@Chuchi-2325]

Hello James. Chris from Pennsylvania. Last year in July I bought a Toro 8 horsepower snowblower. It had good compression but did not run. I bought it really cheap. Once I got it home I took the bottom pan off 5 hands full. mouse nest. By the way I use Anti-Seize on axels it just works better. 🤗

[@tombauer7330]

James, love your attention to detail and desire to make things right in all of your projects.

[@c-qc-q2021]

KZbin is amazing. I once had an old 2 cycle motorcycle that was balky to start, and eventually wouldn't (start). After watching this video, I'm convinced it had a bad coil. Alas, I sold that classic machine and have regretted not being being more talented to diagnose it properly.

[@redneckbryon]

Properly maintained these engines will run forever, Tecumseh’s are definitely some of the best snowblower engines. The engine will definitely outlast the actual snowblower. Fluid Film works really good for lubricating the drive assembly on snowboard, as long as you don’t get it on the desk, but if you do, make sure you clean it off.

[@dhache1195]

Still have my Ariens 8-24 of 1973 with Tecumseh HM80, original engine (a little bit tired but still blowing snow quite good) Just maintain it and it last ;-)

[@swallowinn4410]

Hello Jamea well done. The old TroyBuilt is Ready for another 20 years service.

[@charlesmisiak4926]

I love your longer videos. I feel like I can watch you work for hours. Oh, wait, I just did! LOL. That snowblower is a beast.

[@mikehotchkiss8975]

Warts and all. I will feel less bad after pulling my project back apart after putting it together in the wrong order. Nice work as always

[@mrobi5797]

Great refurbishing James. I did the same repainting with an old snow blower and put apart the engine, auger, and drive mechanism. Took me 2 and half weeks for painting it with two coats of primer and two coats of finishing paint, but the outcome was amazing. Sold it for $490.00. I was happy and the buyer too, since it looks like new.

[@jcondon1]

The prep and painting was a lot of work. Much more then everything else. Kind of hated to put it to work after that.

[@Kinann]

@@jcondon1 Just think if you had a sandblaster how much faster it'd gone, you know you want one!

[@Tailss1]

@@Kinann Needle scaler is also a good option and less expensive/messy.

[@christainchavez7583]

This guy is really passionate in fixing anything he does truly appreciate these informational videos

[@WilliamSchwahn]

Love it when you have " an oversight on my part". That is so typical of so many of us. Since joining your site, I have found my self taking those extra few minutes to do the job right. I feel like I learn something new during each video. Please keep them coming.

[@rickdecastro4584]

Boy, does this bring back memories - that is the same snowblower I had when I lived in Canada...except mine was labeled Canadian Tire.....

[@ph770]

James. I really enjoy the thoroughness of your videos. you take the time to include all aspects of the rebuild. Very complete and educational. You do a great job!!

[@billkinsey2690]

😊

[@jimcwerenz9185]

I’m starting to do my own work. This is very well done. Step by step. Good explanations and good camera work. Thank you for posting.

[@reneberthold334]

I love this channel. Your troubleshooting approach has already helped me with my own lawn mower. I thought I'd take advantage of the winter and just finish it off. It turned out that the carburetor was completely dirty.

[@steveo4749]

James, I'm so glad you spent the time to paint the body. It looked so good. Excellent job.

[@jcondon1]

Thanks 👍

[@martyb3783]

I wish all mechanics were as conscientious as you are. Great job!

[@lv_woodturner3899]

Well done. Now has a good second life. It may not have been used much, but it was left outside and neglected. I have an Ariens snowblower purchased back around 2007. This has powder coated paint which is holding up very well. I keep the machine in my garage when not being used. This has the heated grips which I thought would not be used, but now I am a convert. I use the heaters even with gloves. A big help in keeping the gloves dry on the inside and warm.

[@kencabanaw4165]

Im not surprised at all. Having owned the MTD version of this machine with that motor for 25+ years, It still starts first pull on last years gas. The electric start hasnt worked in years but it's such a runner that I've never needed to replace it.

[@chrisssmallengines7163]

Mice like the drive train box as well as the blower housing for building nests , so always give a once over before winter .

[@superfram81]

James is the best on youtube when it comes to every little detail. And he is a wonderful person. Thank you so much James. God bless you and your family

[@marcheld]

35:17. I always find watching the ultrasonic do its thing in double time oddly satisfying.

[@Kiltylake]

I do a lot of chain saw puttering. When I get an old saw with a rusted chain I soak it in vinegar overnight to remove the rust. It works quite well to free them up.

[@joelsheebs728]

Exactly, I used vinegar to remove rust on an old cast-iron fry pan and it worked beautifully!

[@philliphall5198]

I do the same thing but after I take them out of vinegar I raise them and into a tub of engine oil for a day

[@brealistic3542]

You have one of the best channels on KZbin but probaby don't even know it. Thanks tremendously pal..

[@thomaschew2191]

I have a Husqvarna snow blower with the same motor. I had it sitting in my shed for about literally 10 years. I always run the carb dry but was expecting a clogged carb. The machine needed the starter motor gear replaced, the stator replaced and some parts in the blower assy all of that I replaced/fixed. Then drained the fuel tank and refilled with good gasoline. Motor started with ease. Used it last weekend we had about a foot of snow first of the season.

[@arthurbiringer5676]

Another award winning resuscitation! Great work!

[@michaelmathews295]

You need to lubricate the tire bead when installing it with a tool like that. They make specific tire mounting lube but Armor All or something equivalent would work also. It makes it seating on the rim easier. I also coat the tube with some talcum powder so it won't fold up on the inside of the tire. Installed hundreds of motorcycle tires with a Harbor Freight manual machine.

[@thesilentonevictor]

I am a hvacr hospital tech just love your troubleshooting skillset watching from the Caribbean 🇱🇨

[@russellmaddock3492]

Great job, James. What looked at first like a snow blower that was not worth fixing up, ended up being a decent snow blower. Sense it is an older Troy Bilt, it is a much better built machine compared to the newer ones. And those Tecumseh Snow King engines if not neglected are great engines. I have two 1980 Toro snow blowers that my dad bought new with Tecumseh engines that are still going strong. I was the one who kept them maintained for my dad. Now that he and my mom are passed on, I still use them every winter. Another thing that you could do to increase performance of the Tory Bilt, especially in heavy wet snow, is install an impeller kit. Excellent and very entertaining video. Thanks for sharing.

[@williamfoote2888]

That one wasn’t a two stage?!? I simply assumed it was. Seeing it move the wet heavy snow, without a second stage is pretty impressive. I’ve got a two stage belt driven snow thrower on the front of my tractor and it gets boggy when it’s a heavy wet snow.

[@hoveycorbin5712]

Aloha James. Great job on this snow blower. I wish I had someone give me a 10 hp snow blower like this one! I have an older Ariens 4 hp 24" snow blower that I use here in New Mexico, but sometimes I need more horsepower than the 4 hp snow blower that I have. When the snow does get really deep, I just take a partial pass and it works well for me. For the rusty parts on this snow blower, you need a Roto-Strip wheel that goes into your drill, and it will take the rust and flakey paint right off right down to bare metal and make it ready for priming. If you have a drill that will run 3,000 rpm, the Roto-Stripper will work even better and quicker. It will even get down into the pits of rust in the metal and get the rust off the surface. I have a coarse wheel and a fine wheel Roto-Strippers and they work great for removing rust and flakey paint. Also, you should do the paddle upgrade on the 2nd stage impeller blades and install rubber on the ends of the paddles with the rubber screwed to them, and then you can send even really wet and slushy snow back to where it came from. My snow blower used to clog up on wet and mushy snow, but after doing the paddle upgrade with self-tapping screws, now it doesn't clog up at all, and you can throw the snow much further. The small gap at the end of the paddles inside the 2nd stage cylinder causes the snow to gather inside it and clog up the discharge chute, and that jams everything up with a big mushy plug of solid ice in the outlet chute. The paddle upgrade will prevent this from happening, and you will probably never have to clear a plugged up chute ever again. It is easy to do working through the discharge chute opening, and for you it would be a piece of cake, and it will make your machine perform much better in the wet and slushy snow. Watch some videos on line and you will see just how easy this modification to your snow blower will be, and you will be pleased with the results. Way to go on this job!! I really enjoy all of your excellent commentary as you work through a problem, no matter what it is... Aloha..

[@johnbush6262]

Aways a treat to watch you diagnose and solve the problems while educating us (me) thrown in. Good to see the Endo files are helpful for you, I have tons more--let me know if more needed. Thanks again

[@jcondon1]

I really like that yellow one with the tapered file. It reaches well into the smallest jets. Thanks again for those.

[@BigEightiesNewWave]

Speed-blowing bonus footage.

[@Chuck_in_CT]

James... The best way to clear snow is with a cup of coffee in your hand looking out the window watching your son doing it

[@georgelequin5070]

😅

[@larrywolken9215]

Congratulations Jim! Another great, lucid, clear, well-produced teaching video - with no ego. Thanks

[@curto9664]

that little gem you have is almost the same one i have got. i had a earlry 1990s mtd,montgomery ward 8/26 8 hp snow king tecumseh put new tires on and a drive disc painted the auger etc,adjusted greased and rebuilt that crappy tecumseh carburetor. what a gem those carbs are. i run non ethanol 91 octane and 10 w 40 in this thing. make sure that govenor is always working as it sopposed to . this little monster pushes sno and will even cut down the snow that was plowed in medium snow banks. i live on a farm with a dirt driveway and this thing will give you a real good workout.ive also have a 1968 yardman 8 hp snowblower that i have to work on belt alignment. it keeps on throwing the belt off. it has a picture of a pelican on the front bucket scooping up snow with its beak. another free machine a freind got from an elderly neighbor. the relics sometimes are better than the new junk that is made.take care i watch every week what ever you fix.

[@eric_seguin]

My Dad swore by Troy Bilt garden tillers. Problem is, when they broke I got to work on them. Thanks to you and Mustie1 I have no questions about snow blowers. Oh wait, I live in Louisiana. Oh well, it was good entertainment. Thanks.

[@kd5byb]

"Earned it's oil change" always makes me smile!

[@larryfarquhar8211]

James, I really enjoy watching your videos! You keep them interesting and are very thorough! I live in central Texas and watched the whole video of you working on the snowblower! I work on mowers, string trimmers, and leaf blowers as a hobby. I don’t see many (any) snowblowers around here, but did enjoy your video! One of these days I’m going to tackle a generator. I see them all the time on marketplace for sale for around $100. Thank you for your videos!

[@jerrypeal653]

Rust , the reason I bought a sand blaster. Don’t use it often but it’s worth it when I do . I also cook chains like that in pan oil on the BBQ. Impressed how thorough you are !

[@readyplayer2]

This is probably well known by most living in the rural West, but in areas where mouse borne hantavirus is prevalent, don't do what James does at 22:10 or so, and blow out a mouse nest with compressed air. Saturate the area in a bleach solution, and wipe out. Not a dig at James, rodent spread hantavirus is pretty unheard of in the NE. It's not exactly common in the West, but it's a really nasty disease and it's usually acquired by stirring up mouse waste by sweeping or vacuuming and breathing in the virus.

[@rockcralwer]

I have come to your channel not that long ago. And I just find myself lost trying to watch all your videos. Please don't stop doing what you love and sharing theses videos. Well done sir. And thank you for sharing your time and knowledge with us

[@iskydivetoooo]

A good ultrasonic cleaning of the carb and you should be good for a snowy season!! 😁 Usually I use diluted simple green in my ultrasonic cleaner.

[@48shams]

Since the 80s I've used baby powder to get inner tubes into tires. Powder the tire and the tube and they slide right in and don't bind up. Makes the job a ton easier. Great video, as usual!

[@dadskrej5226]

Another good video Jim! a little soapy water on the bead area of the tire should help your tire changer put the bead on easier. I realize.it is an old tire, but it should help some. Also you missed lubing the grease zerk on the shaft where you put the new chain, and cleaning the drive wheel to remove any grease that may be on it. I may have missed seeing you do these things. Nice machine. I have a 2021 TroyBilt Storm...works great!

[@wildmanofborneo]

Best to use hair conditioner on the tire bead.

[@davidbgraham461]

From snow free, Melbourne, Australia, that looks impressive !! Thank you.

[@richb419]

Hi James, dirty oil is what I like to see before working on engines that someone else owned, new oil usually means that the owner caused engine failure. the carburetor is most likely made of a zinc alloy like many auto carbs from the 60's. you might want to check the grease in the auger gear box, probably ok. Rich

[@jcondon1]

Very true

[@geoffmolyneux9173]

😅😅😅😅😅😅😅

[@nevrstopdrivin]

I purchased a “99 TroyBilt 8hp snow blower in “17. It was like new condition. Paid $325. It’s an absolute beast. It’s the all metal version with the metal chute. We had over a foot of snow today in Wisconsin. The machine bulled through it with ease. I service it every spring before tucking it away. Mine has a hood, hand warmers, and headlight. It’s an awesome machine. Thanks for posting this.

[@stazeII]

*wakes up not remembering what day it is, blearily drinking coffee… checks youtube* It’s Thursday! And a nearly 2h video!

[@jcondon1]

Nice

[@alfredocuomo1546]

No Doubt there have been no snow storms like we had in the early 90's where they were several ft. but in the last five years I think I had to take my electric snow thrower out once. Can't say that I mind, I don't like the cold anyway. Nice job. after watching you work I have a new name for you and that's "Picasso". Hey quick note, some tires are more easier removed from the back when you have rims that are not symmetrical. This was true for many of the Mag wheels in the automotive field.

[@brealistic3542]

I live in a apt. Complex where people are always throwing appliances out that actually are fixable.I hate seeing still dry usable expensive items tossed out. I once fixed a top of the line Keurig coffee maker that had a bad pump. Keurig made the machine so that it was nearly unfixable because disassembly was ungodly. It took me days and days to get it apart.

[@Rick-hp6fu]

James, thanks for going the extra mile and painting that snowblower bucket and auger. You brought that snowblower back from the dead. That machine is nicely built. I was surprised that the engine ran so well after getting the spark issue resolved. I have a much newer version of that same snowblower with the smaller Briggs engine and mine struggles in slushy snow. We're going through a snowstorm in the Chicago area right now so I got to put my snowblower to work earlier. Did much better with the heavy snow today than with the slushy mess we had a few days ago where it kept clogging up. If I would have sprung for the larger engine model when I bought it, I wouldn't have had issues. Great job!

[@HotrodRon74]

i have one just like this in the shop..mines a ten speed with rev..a 2 stage...i bought it off a guy near Pitts..he said he could not get it running.it was like new..so i brought it home.it had no spark,,,.it took a plastic key to turn it on,,that moved two pieces of steel apart,to unground the coil..so guess what,,the two pieces of steel were rusted to each other..not ungrounding the coil..so i put fresh gas in it...and fixed the key switch,,like throw it away..haaa,,i put a switch on it...i dont use it a lot,because i have a blade on my 4 wheeler...but it is a backup...a nice buy for 75 bucks id say..i used it for 2 years,,does it throw the snow.. you brought back memories James..great video..

[@FailedSquare]

These blowers were AFAIK all built by MTD and are fairly common to see rebranded as troybilt, craftsman, and several others. I have one that's near 20 years old that was given to me this summer and it's identical aside from the cowling. The motor runs like a champ. Tecumseh made good stuff

[@joevalencic5275]

I was going to make that point as well. MTD right here in Cleveland Ohio makes most of the big box machines, and so many parts are interchangeable. I noticed the Craftsman label on the used belly pan…that cinched it right there.

[@rogerbeck3018]

I wish I had the same meticulous mindset, but I do not - I do enjoy your videos. The editing really seals the full package. Very Well Done and thank you

[@lucilleking7495]

Hi James, Great video, I have nearly the same thrower, but Canadian Tire model I bought 25 years ago , do 18 driveways and sidewalks every time it snows here in Ontario. Always starts just run premium fuel , had to replace some parts over the years but that's to be expected, Put rubber extensions on the impeller cleans tub out real good, biggest problem was throttle control engine would not stay revved up, Put a cable control up to the console , Works great, Hope I never have to replace this machine. Gord Ontario Canada

[@S15GYPSY128]

Thank you Sir learning a lot about generators from your channel still confusing and complicating but learning as I watch your channel hope you keep making videos and hope you your channel going

[@1nickoli1]

If someone hasn’t already commented this… spray and coat the inside of the discharge shoot with Pam cooking spray. Really helps with the snow discharge! Great job as always!

[@georgepretnick4460]

James, Your diagnostic skills are legendary, but unless this old snowblower is going into museum or to a snowblower collector, you got a little carried away with the paint. You put well over $2,000 in time and parts into an old machine that is of diminishing value in a warming world. on the other hand, you made a great instructional video.. Thank you.

[@jaibradford3932]

Honestly pls keep the videos coming, the way u construct your videos is flawless. I know it’s not easy to construct the videos so thank you 🙏

[@johnmckee7937]

What a beautifully made machine. Great job refurbishing.. One quick point, clip leads Do go bad so always check them if there's an issue.

[@frankie7508]

great job james! This video helped me realize that my throttle linkage is not correctly attached. The second thing I really like is the quality of the build of the machine from twenty years ago. Thanks again and take care. Best wishes for success in 2024. 🎉

[@bluesfan51]

I really liked the dish soap idea, Dawn might be a good choice.

[@smplyizzy]

I live north of Philly. What amazes me is the number of new snow blowers sold at Lowes and Home Depot every year. The reason I say that is in last 4 yrs or more we have not had more than 3 inches of snow on the ground at one time.

[@curtdunlap6818]

Another great job! Sometimes a spray of WD-40 or brush of diluted dish detergent will make those bead bars slide around the tire easier. Sometimes those tires are so hard that they just don't give easily. I broke my aluminum bead breaker bar working on my Deutz Allis rear tires on the first use! The rest of the HF kit is still usable.

[@davidduvall4655]

I have a 45-year pld Roper snowblower that internally is identical to that one. Same engine, yours has fancier controls but you can tell quality has dropped over the years. The frame and belly pan on mine is 3/16 steel. You do not want to drop that pan on your foot. Don't ask. Great video getting an old machine new life. Bought mine in 1979 still runs good just haven't had the snow to dig it out.

[@FredD63]

Just a little tidbit Johnson, Evenrude 2+4 cleaner works good on the inside of the carburetor if it’s not very green it can be bought at your local marina or at the Sporting Goods department at Walmart. breakaway spray really helps with removing and installing tires.

[@robertmailhos8159]

🎉Yyou are definitely right about the ignition coil being mounted on the engine in the right position to get spark I've been there did that as in putting it on the wrong way had to turn it around and it worked out just love how the powder coat is peeling off the metal those tires are the same ones that are. On my craftsman gt tractor I've been told that I have them put on backwards so I have to get them put on the right way glad you are doing this snow blower justice by getting it up and running again James

[@weathermannax416]

I got my father's Yard King snow thrower & it has that same exact 10 HP Tecumseh Snow King engine. He bought his brand new in 2001 from the Home Depot. That engine now has 178.41 hours on it. I just ran an extension cord out to the shed as we have a winter storm heading our way with bitterly cold temps. So, Lake Michigan snow make it happener machine will be kicking into high gear here soon. They are talking about a foot, maybe up to 2 feet of light fluffy lake effect snow & 60 mph wind gusts.

[@paint52]

I did the same procedure on my Daughter’s Toro PowerMax 10-28. It’s a lot of work but the results were so satisfying. The powder coat original paint failed like yours did. Super work, enjoy your videos.

[@Amy_McFarland]

Whenever I've used PB Blaster I always let it soak for at least an hour, giving it an additional spray every 15 min. It had never let me down. For very stubborn items I'd let it sit overnight. Again, always worked with patience on my part.

[@britboy2883]

I have a 20yr old Ariens 1128 snow blower with a Tecumseh engine, never missed a beat !

[@McNunkyNutz]

The most impressive part is, the amount of paint in that one can. ;)

[@mjg263]

Man, what a great job James! MTD uses the crappiest paint right from the factory plus they don’t prep the metal before shooting it. Just about every MTD product I’ve ever had or worked on has had paint come off in sheets like it’s latex interior house paint. Chances are the rust started forming after the paint peeled off, and of course leaving it out in the weather really did it in. Anyway, great job and it looks like you may get another chance to give it a workout this Tuesday!

[@JohnSmith-yv6eq]

And hot dip galvanising was invented in....? The name “galvanizing” was first applied to the process invented by Stanislas Sorel. In 1836 he patented a process of cleaning steel and then coating it with zinc by dipping it into molten zinc. He called the process of galvanizing the “galvanic” method. This was the beginning of modern hot-dip galvanizing.

[@Rein_Ciarfella]

I am SO jealous! I saw you blowing with no gloves on! This machine has every single bell and whistle I would want. I have a yard and garage full of snowblowers, all free except the first one I got. Some are in excellent condition and some are really nice, but none have lights, steering control, remote chute elevation control or heated handles. You lucky bastid! 😉👍

[@blknblu8303]

did a rebuild last year on my 30+ year Craftsman track drive blower (made by MTD). Went through everything & re-painted it. The Tecumseh Snow King engines are tough. Mine starts first pull every time (even sitting for months). Important item to add is a fuel shut-off valve.

[@robsteinhaur221]

Wow, you put a lot of effort into this snowblower with great results. Thanks for sharing.

[@truckmann1762]

I got the same 10 HP Tecumseh Snow King engine on my father's snow thrower he bought new November 1998. That engine has 184 hours on it & still runs great. It too doesn't see much action these days. Maybe 2 or 3 times per winter. My JD X350 gets more use plowing snow.

[@tonygriffiths2485]

You put a heck of a lot of work on that, and then showed us an ad for a slightly lesser machine being offered for free. Talk about ironic ! Lovely job though I enjoyed all of that, thanks :)

[@somerandomguy3868]

A fine job as always, only one thing caught my eye, I believe it to be the intermediate shaft on the right side seemed to have some movement in the mount, keep in mind I could be wrong

[@davidhaag9116]

James, you do a really nice job and looking at the weather you’re gonna get a chance to use that in just a couple days

[@earlwarren2265]

Just think Jim, with the big blow coming your way this week end you'll be able to get alot of use out of this unit. Have fun. Earl in Michigan

[@Got2Learn]

Very nice!! The third word in the description is supposed to be "troy" just FYI ;) Thanks James!

[@jcondon1]

Thanks. Just updated. Will have to talk to my editor (me).

[@whatdoyouthinktodd]

I grew up in our family owned body shop. You can't imagine what I'm feeling right now with the level of paint prep😖 this machine is a survivor. It deserves to be torn down cleaned up and painted with care. Using 75% active vinegar on rusted parts works wonders.

[@JohnSmith-yv6eq]

Galvanising was available since 1836. The manufacturer should have been doing this to all these machines...

[@tristanschaper281]

James, I agree with you - the snow blower market has really gotten weak the last few years. Older units that would have sold for $500-$700 5 years ago, are now "asking" $250-300. I have fixed and flipped about 7 units in the last few years, and the market has sure been soft lately. And just like you said, its a LOT of labor, even if you have a running engine. Great job on this as always! And it's funny, when you first engaged the electric starter, I said to myself, boy that's super fast spin! And then you said the same thing! I was almost thinking there would be a compression issue, since it was spinning so fast.

[@GNX157]

James, back in the early to mid 80’s, I worked on a ton of GM computer command control (C3) Rochester quadrajunks that came in with drivability problems. Almost every one of them needed a complete reset. Float level was low, idle mixture screws in the baseplate too lean (had to remove carb and drill put the plugs), and the max, minimum and travel distance on the metering rods was off (mixture control solenoid was moving those). Then on top of that, the Oldsmobile 307 Y engine, almost every one, besides needing a carb rework, had a bad evap canister control valve.

[@johnmenzies-rg3vj]

James Another great informative videos. Keep them coming. We all learn so much from you Thanks John (From New Zealand)😊

[@user-tg5wg6oe6o]

I can smell the spray pain from here. Great job!

[@markwiley9516]

Great job James 👏 love the work it looks great 👍 and runs very well

[@generessler6282]

Looks like a new bench vice! Cool. Amazing how a good vice helps get things done... Happy New Year 🎉 Hey for rust removal and paint prep I recently got a cup wire wheel for the hand grinder. It works really well for stuff like the bucket because you can apply pressure toward the surface easily.

[@jcondon1]

You are the first one to notice. The Cub Cadet tire I worked on last summer did the old one in. Here is its last moments... kzbin.info/www/bejne/m3SVfqqHp96Ea9U

[@RossReedstrom]

@@jcondon1 Bonus content! Y'all it's an unlisted video, 22 seconds of machine shop violence. :) Clearly, someone's been eating their Wheaties!

[@hillppari]

Spraying some teflon or silicone spray in the bucket really helps with snow not sticking