This video documents the process of the diagnosis and repair of a 2015 Jeep Wrangler with a distinct tapping noise coming from the engine.
Пікірлер: 301
@alainbrisebois8334 Жыл бұрын
You have change only the noisy one....so that nex week , you have another rocker job to do, and the week after....GOOD JOB JUNIOR !!
@billjones4926 Жыл бұрын
I have to disagree with one of the comments about removing the battery tray. I watched another video of someone doing this same thing. They had me jacking up the Jeep, removing the tire, removing the wheel well liner, and I still couldn't reach the back bolts. Luckily, before following the other video, I happened to watch just a little bit of this one, and I remembered him mentioning removing the tray. After cussing and bitching about the rear bolts, I took out the battery tray, and the whole thing opened up!!!!! That was the single most important tip in the video IMO.... Also, without removing the battery tray, it is almost impossible to remove the valve cover...
@plainjane3786 жыл бұрын
Been trying to figure this one out for a while on my jeep... thank you for uploading this!!
@gregwatson82464 жыл бұрын
Thanks for this video, it helped me out alot when my son and I changed out a rocker arm and Intake cam due to "ticking" problem allowed to go too long, in a 2015 Jeep Wrangler. My only addition is, removing the fenderflare and wheel-well liner (as a single assembly) allows the best access to the back and side of the valve cover for easier PCV valve removal. Don’t worry about the battery tray (too much work dealing with relay box, IMHO). Second, remove the transmission dipstick and then loosen the transmission dipstick tube (two bolts (upper and lower, the upper is easy with wheelwell liner removed) and move the trans. dipstick out of the way. That makes the PCV valve easy, easy.! If cam replacement is necessary.....heres what to do. Do your research homework first, then.... The timing chain and phaser sprockets need to be removed, but no special tools are really needed for timing chanin tension release. That said, the special tools are inexpensive on Amazon and I recommend getting them as a set. Find TDC exhaust stroke #1 (or #4). Cam sprocket *arrows* align on left bank and cam sprocket *lines* align on right bank. Mark the chain and sprockets. For bank 1, Wedge a thick flat blade screwdriver between the 2 sprocket's teeth HOLD CAM ON CAMSHAFT HEX CASTING WITH A WRENCH and loosen phaser sprocket bolts with 36mm socket. (its tight, 110 ft.lbs) slide phaser/chain back a little off cam use a long thin (18'') screw driver to lever the tensioner and releave chain tension to slip chain and sprockets back on, and wiggle rotate the camshaft a little to engage the phaser sprocket and slip it back on. Its easy it you understand what your doing, and my point is, no special tools required for tension release on bank 1. Bank 2 is the same process, but requires a couple bent coat hanger pieces to release and then hold tensioner mechanism. (explained in other online videos.)
@coolguy4185 жыл бұрын
Great video, I will send it to the two mechanics that tried and failed when attempting to fix my jeeps ticking noise!
@ZXRTDub693 жыл бұрын
My 2009 Jeep Wrangler has this issue . I took to a mechanic shop said it was easier to change the engine . Thanks for the upload
@garroy70512 жыл бұрын
I am sure by now it's a year later that you figured out you do not have a pentistar v6, you have the 3.8 minivan motor so good luck, just saying
@marcobarrera15725 жыл бұрын
Thank you for sharing this video I just finished my left side and your video help me a lot!!! Thanks again.
@pedroevangelista71985 жыл бұрын
thank you so much for the specs on the camshaft cap it helps me so much. Great video.
@mikeu22063 жыл бұрын
Just did one and mine was the first rocker behind the intake cam gear, if your nice with it and remove all the caps you can lift the whole cam up to able to remove all rocker arms without messing with the timing. slow and steady waiting for the oil to drain from the tensioner.
@Vandale19745 жыл бұрын
Thx for the video. I have the same Problem on a 3.6 dodge charger pentastar. I will fix it next week. Greets from Germany
@WonderingAimlessly4 жыл бұрын
Nice vid. Right to the point with perfect volume of detail. Crappy Chrysler. 51k and a bad rocker already! Never getting rid of my 2003 TJ. Still strong, and stock rockers with well over 130k on them.
@HighLifeRocker5 жыл бұрын
Great timing on your video... I have a ‘12 JKR @ 92k mi. I really don’t want the local stealership to do the job, but its a daily driver. I suppose I’ll have to compile a couple lifters & rocker arms, get in there & see whats up. Thanks!
@karlschulz24246 жыл бұрын
Thanks for the info, my 2012 Grand Cherokee started tapping a month or so ago. I thought it was valves, was just going to leave it be.
@kristinsaunders38515 жыл бұрын
Thank you for this video! You saved me a big chunk of change!
@rustywhite13 жыл бұрын
Great video Justin...Solved my 2010 wrangler problem by not messing with it..lol...Thanks for posting this....
@dethwsh1283 жыл бұрын
love the detail you go into. great video, first one for me
@gabriellecorritore86212 жыл бұрын
Thank you for this video! I just bought a 2014 wrangler with 47k miles and the ticking noise is driving me insane. Watching this video makes me feel confident this is the source of the issue!
@waltmartin922 жыл бұрын
rockauto SKMR1332 $4.51---- time to change ---- ∞
@gueroburban4989 Жыл бұрын
Did you ended up doing it?
@johncalhoun65384 жыл бұрын
I have the same year, the same issue, the same color ...lol and I have 50,312 miles... taking it tomorrow to get fixed thank you for the video.
@gsabella43 жыл бұрын
What did you pay at a shop for this to be done?
@CCF_Christopher3 жыл бұрын
Awesome Work!!! My 2014 Jeep Wrangler started making the tapping sound last week.
@halv80593 жыл бұрын
Did you do anything to correct it? Mine is doing it too
@CCF_Christopher3 жыл бұрын
@@halv8059 I got the lifters and Rockers replaced on the left side along with the Cam... The Right Side is ticking now so I will need to get it replaced as well... The Dealership should have replaced both at the same time.
@6000cs3 жыл бұрын
Thanks a bunch for this. My 2016 Right Drive that I deliver mail in is doing this at 99k. Has me worried badly, going to garage on Monday. Now at least I'm a little less worried, hoping this will fix it.
@ChauSemperfi074 жыл бұрын
Great video brother hope to see more, now you've confirmed my suspicion of the lifter lol thanks alot
@thayerm12 жыл бұрын
2013 Jeep Grand Cherokee. Replaced all rocker arms and hydraulic valve lash on the right side of engine immediately after hearing ticking noise @119,328 on 8/26/21. One rocker arm was bad and 3 had some play. Job needed a valve cover gasket set, upper intake gaskets and Throttle Body gasket (not replaced). Replaced torque crews on PCV valve (old gasket used) with 5mm bolts for easy access. Remove the throttle body to access the 2 throttle body support bolts. Two bolts removed to relocate transmission fill tube. Special tools needed to secure the cam shaft. Lifter: 12x: MELLING JB7525 Rocher Arm: 12x: MELLING MR1332
@sebastiankiely4534 Жыл бұрын
This is a great video. I just bought a 2018 with 43k miles that has the same sound.
@djtechinics97dj376 жыл бұрын
Great video. I did the same way thank god they were in the back and not near the cam phasers. One thing I did different was I soaked them in oil overnight before I installed them
@justindriskell94736 жыл бұрын
djtechinics97 Dj good thinking
@john-mike21085 жыл бұрын
Thanks for the video. I just replaced my rocker arm today.
@michaelmason19324 жыл бұрын
Great video nice job. You explained the issue and your video was very informative.
@rosssyster5 жыл бұрын
Ahh yes, the ever-present Pentastar tick. Seen this in multiple Chrysler vehicles I have. Never seen it fail at such low mileage though. I’ve found this normally happens right around 100k or so. Thankfully it’s a straight forward and relatively simple fix.
@williamrobinson3014 жыл бұрын
THANK YOU!!!!!!!!!!, It's been driving me crazy, I took it to the Jeep Dealership off Tomball Parkway and Paid them to find out what the problems is just to be told they don't know and I need to pay more to find out what the problems is.....
@Cambodimerican244 жыл бұрын
Literally just had this similar tapping sound coming from my 3.6 pentastar today. Hopefully it’s just a bad bearing too. I just hit 105,000 miles so all in all she’s been pretty bulletproof.
@Gunalizer3 жыл бұрын
In the US 2015 was the last year of the 5 year/150,000 mile drivetrain warranty from FCA. 2016 and up are 5 year/60,000 mile. I had a cylinder head replaced that was showing a misfire in cylinder 4 with close to 40,000 miles on it. From what I understand, problematic heads were an issue because of faulty manufacturing on a lot of older 2012-2013 Jeep Wranglers, but my 2015 still had it. There's a good chance that these ticking problems can be fixed under the drivetrain warranty.
@davidtaylor95085 жыл бұрын
Thanks Justin, this was my problem too, 80k on mine, but of course mine was on the driver side. I replaced all 12 while I was in there and spark plugs also. I like the video short and to the point, saved me loads of time on diag.
@justindriskell94735 жыл бұрын
Thanks man. I tried making it short. I hate watching videos that are like 20 minutes long and having to jump around the video trying to find the info you need
@jessecharles2995 жыл бұрын
You said driver side, was it the bearings that made it clear up?
@jrrincon795 жыл бұрын
I’m havin the same issues on a 15jk but my engine light is on can it be the same problems?
@Cbv19144 жыл бұрын
Jr Rincon check this service bulletin if you haven’t had it fixed yet. Just good the following 09-002-14 REV. B
@majidalhooti16934 жыл бұрын
David Taylor How was the camshaft! mine got very minor damage on the edges! now thinking to replace the rockers and lifter and leave the camshaft as its since its 100% fine where the rocker bearing seats? any advice! TIA
@harrison22815 жыл бұрын
*PLEASE READ* Fantastic video!! I just replaced the driver side. It's similar to do, but different because you have to pull the upper intake manifold to get to the valve cover. If you have this tick PLEASE repair quickly. If you let it go for long, the body of the rocker will grind into the cam lobe. Obviously this isnt good for the cam, but also puts metal into the oil. Thanks for the trick showing how to NOT pull the cams, and also for including the tq spec. Edit, the part is $9 on rockauto.
@Cbv19144 жыл бұрын
Harrison the part is also only $6 from Moparpartscorp.com
@mh-tn3ic2 жыл бұрын
Good job I am going through this now with my 2015 JK with 70,000 miles
@armedprophet33213 жыл бұрын
My wife’s 2014 had the same issue just 5000 miles out of warranty. The dealer stated that there was a TSB on it and Jeep fixed it for free. They totally replaced all the rockers and lifters on BOTH sides.
@lonnievermette57865 жыл бұрын
I had the same problem on my 14 T&C and it took me 3.5 hours from start to finish and I’m no mechanic... well I am an oilfield trucker so I’m pretty handy on the wrench lol
@mmirek-dr2vq5 жыл бұрын
Très belle video et bien fait . Merci
@justindriskell94735 жыл бұрын
Merci. J'ai travaillé très dur dessus
@thomasfury69275 жыл бұрын
This is exactly my problem. A '15 jk with 51k miles. Is even the same color, ffs! Thanks for the info, i feel better taking to my mechanic, now
@karcharias8114 жыл бұрын
My 2016 two door Rubicon is just now hitting about 50k miles. Will be listening closely.
@elcuate00015 жыл бұрын
I fixed the ticking noise passenger side (6 months of loud ticking) on my Pentastar engine 3.6 Jeep 2015 with the Marvel Mystery Oil and I returned to Conventional Oil. No more synthetic oil. I'm so happy now.
@ricvanwinkle16656 ай бұрын
You fixed Jack
@zxtuner4lyfeАй бұрын
@@ricvanwinkle1665 lol that engine has since ate its cams alive LOL
@nino-cu1wm5 жыл бұрын
Very nice video...thanks
@JimWellman4 жыл бұрын
Fantastic video. Thanks.
@Philosofize14 жыл бұрын
Great explanation!
@RandyRhoadsFan822 жыл бұрын
Chrysler tech here….2 things. #1: the bearings are not the cause of failure in the rockers, it’s the soft metal they use for the pins that the needle bearings ride on. They wear away the center pin causing excessive clearance. #2: don’t repair your vehicle like this guy. Replacing one bad rocker? ALWAYS replace all 12 rockers on intake and exhaust. Chances are you’ll be right back in there to replace the other ones. Do the job correctly, you can cause unrepairable damage to the cam journals.
@bradr58102 жыл бұрын
This is the correct answer. (Replace all 24 since upper intake is off IMO). Need to inspect the cam as well to see if you have worn grooves already from the bad rocker(s)
@kpfalconi2 жыл бұрын
The PCV valve is the biggest PITA on the jeep, especially that top bolt.
@sashathompson73514 жыл бұрын
You suppose to check the cam too once your replace a rocker cause sometimes the broke rocker chews into the cam and also your suppose the change the oil after you change the rocker to get the shaving from the rocker out just say your going having problems again down the road if you dont
@kimmytx3 жыл бұрын
Thank you sir. Much appreciated
@robertscharfe98793 жыл бұрын
Awesome video good job
@erikgiron95962 жыл бұрын
great video ! my jeep wrangler 2015 has the same issue 😑
@foofoojergins97414 жыл бұрын
I see what you did there..... but mine was doing it (2015 jk) which i was running Castrol 5w30 synthetic. The jeep has under 40k miles and mainly would tick from initial start to warm up but i switched to valvoline 5w30 synthetic and haven't heard anything since. It may have been a bad batch of Castrol or better zinc content in the valvoline IDK.
@captainrobthompson87285 жыл бұрын
6 hours and no ticking!!!! What a bitch that valve cover is. I found it! Intake last cylinder I'm guessing #5 passenger side just like you said. Thanks so much Justin!
@michaelmason19324 жыл бұрын
Very important on this engine to maintain regular oil changes with full synthetic. I have been told some of the bearings used are not the same quality they used to be. If the oil is kept very clean, and pcv valve is working correctly this will greatly improve the operation of the mechanical components in the upper engine.
@pauljoey79774 жыл бұрын
Yes
@dharkundercity17964 жыл бұрын
I have a 2014 JK and have dealer changed my oil right on recommended schedule for the past 5 years with 93K miles and this just happened to me last month, so regular oil changes at the dealer will NOT prevent this from happening... All moving parts will wear out sooner or later. Next vehicle will be a Tesla... I'm done with gas engine vehicles.
@pauljoey79774 жыл бұрын
Change oil every 3k. Fixes mopar rocker issues
@garycasper29292 жыл бұрын
Yes yes yes… That key takeaway here is FULL synthetic oil. Doesn’t matter where or by whom. Nothing to say the dealer was doing it correctly. My girl was getting here oil changed at a “jiffy lube” place when I 1st met her. 3.2 engine ticking with low miles on it. I looked in her glovebox only to find that this reputable joint had been putting conventional oil in the whole time. So, ya never no. You want to trust the “pro’s” …. But , it doesn’t always go as planned.. 👎👎
@tubetime392 жыл бұрын
@@dharkundercity1796 why not have it be later ?? Oil is not oil & whoever tells you different is full of BS. And trusting anyone, including a lot of dealerships is a risk that can be costly,....to.....Y O U ! If you find someone you trust Bravo. Hang onto them. There are some but fewer and fewer.
@chrisbassett87335 жыл бұрын
Great video! Can you get enough lift from the cam to use this method work on rockers closer to the sprockets?
@pilsplease75614 жыл бұрын
My challenger started doing this about 2 weeks ago, 3.6 liter in it was supposed to have been fixed, but I suspect this is whats going on as its a audible tapping/ticking sound.
@bourne2cruise1963 Жыл бұрын
Great video. I have the same problem on the passenger side. Curious on how much the average shop would charge me to do this?
@MrDavidchuck3 жыл бұрын
Hey Justin, hopefully all is well with you and your family, first and foremost. Secondly, I was tapping in to know which tool you specifically used to torque everything back in its place. Looking to do the same job on my 2013.
@dale7974 жыл бұрын
When I took my engine apart the first time to replace a rocker arm it seemed to me that there was very little oil up there in that area, even though I had been using 5x20 oil as is recommended-and that was synthetic! So after it developed the second ticking noise I installed an oil pressure gauge and I switched to 5x30 synthetic oil, and I unplugged the wire going to the solenoid on the oil pump so that it stays in high volume mode all the time. Now I am running 40-55 oil pressure going at highway speeds. When I took it apart a couple days ago to fix the second tick (that started before I made these changes) it has a lot more oil on the rockers and etc. So I think it will have cured the problem of the rockers failing prematurely! But that is my personal idea and I wouldn't be responsible for anyone else's modifications!!
@karcharias8114 жыл бұрын
Amsoil every day of the week. No trouble with mine so far.
@tubetime392 жыл бұрын
@@karcharias811 Bought a used PrlMaster and heard about this problem and changed over to Amsoil. I was going to anyhow. It worked wonders on my daughters Equinox that was having issues. Stalling out etc blah blah. Lemon engine. They eventual did a recall on that motor. PM hasn't been running in 6 months. Lots of issues. But heard tyranny problems also in these. Switching that over to Amsoil also. No competition, that I've seen with their tyranny, gear and hydraulic fluids ! Going all out with their Coolant, PS, and brake fluid. Plan on traveling and hopefully help prevent future issues. It's been good to me for years.
@rustbeltrobclassic2512 Жыл бұрын
I dunno if you still have it, but i run a zinc additive and it made a HUGE difference..
@randy1ization5 жыл бұрын
strong work son!!!
@michaelrussell7783 жыл бұрын
Great job!
@k9deine3512 жыл бұрын
great video
@eqeagle8634 жыл бұрын
Thannks bro...big help👍
@Cbv19144 жыл бұрын
Good video. I just can’t believe FCA hasn’t done a recall. FCA has updated the part and even have a star case about it but not extension on warranty or recall. My local dealer quoted me $1800 to repair it but would only do it if they replaced all rockers, lash adjusters and cams for the one side. It’s nuts that owners get screwed for a $6 part
@justindriskell94734 жыл бұрын
I agree. But they typically only recall items that are severe safety issues. And no ones died yet from noisy lifters. Although they may feel dead when their wallets empty to get it fixed
@Cbv19144 жыл бұрын
Justin Driskell my GX460 just got a recall for a faulty secondary air pump and related items. A little foam filter sometimes degrades over time and gets sucked into the system. Don’t think I’ve heard anyone dying from that but Lexus is replacing all 2010-2013’s I believe. Idk I guess maybe FCA can’t afford it bc there’s already been a recall on the alternator, brake booster twice and sun visor wiring. Not sure I’ll buy a Grand Cherokee again...
@justindriskell94734 жыл бұрын
Very true. Love the way these new jeeps look but their powertrain sucks
@heavyflippingrandmasboifir6694 жыл бұрын
Bro I’m helping a friend do rocker arms and I want to know would you change all at one time or just the nosies one? Thanks again for the video
@majidalhooti16934 жыл бұрын
Thanks for the video. So you replaced all the rockers? or only the one which was making noise?
@DMERJ4 жыл бұрын
great vid. thanks. what would you charge for something like this?
@aldo99234 жыл бұрын
Hey what’s the part number on those rockers and any gaskets your replaced?
@robertfrancisco11933 жыл бұрын
do they make a better replacement rocker for the 3.6?
@Filiricanyahoocom4 жыл бұрын
Can you change the rocker on my 2015 jeep wrangler for me?
@margaretsherwin92572 жыл бұрын
Nice job
@emkadesign46545 жыл бұрын
And what about all the other rockers? If one is faulty why not all of them? I'm asking 'cause I'm going to buy a Dodge/Chrysler minivan with the same engine. Thx for the video!
@michelantoniomorin22014 жыл бұрын
Good video
@steveingalls67982 жыл бұрын
Is there a reason you did not cover the inspection of the cam lobe for wear that would cause another failure ?
@dale7974 жыл бұрын
I got my 2013 Grand Caravan apart and the rocker for the intake in the middle of the back head was shot. Thankfully the cam is still OK, and all the other rockers and the lifters are all OK. So I went to town and picked up 3 rockers from the Dodge dealer to have a couple extra ones. But when I got them home and was looking them over closely and comparing them to the old one-I noticed that the little shaft can be moved back and forth in the cage with my fingers, whereas the old rocker shaft was nice and tight, but its shaft was worn on the inside because the roller can be flopped up and down but not back and forth. Were your new rocker shafts loose in the cage so that they could be shoved back and forth? This doesn't seem to me like it would last very long before the hole in the rocker cage would start to wear oblong!!!
@dale7974 жыл бұрын
Since adding my comment about the shaft sliding back and forth in the rocker arm cage, a fellow told me that it was made that way on purpose so that if the bearing gets worn too much before being being replaced, and the bearing seizes up-then the shaft will turn in the cage rather than dragging the little bearing over the camshaft lobe which would finish off the cam in short order.
@constancemarieconway91524 жыл бұрын
I have a 2014 Jeep Wrangler Willys unlimited / with a Penstar engine with ticking noise, does it apply to mine, my engine and cam looks different
@juanparra7285 жыл бұрын
That’s dude had the same taping sound on the same head .... really save me some time
@randy1ization5 жыл бұрын
theres need bearings inside that chew up the shaft they sit on, thats why im thinking its a oil starve issue
@mustangcrasy-youtube17372 жыл бұрын
Hey question man, about how long of shop hours did it take you to fix it, what do you think would be an appropriate price for a shop to charge to do it??
@sullivanscourier6 жыл бұрын
my 2014 ram 3.6 just started doing this ticking noise took it in for dealer to check it's the same rocker arm that's bad nashville dealer said this fix is covered under Chrysler factory warranty for all makes with the 3.6 under 150,000 miles cause this part is defected my truck just hit 158,000 miles so i'm stuck paying $920.00 to fix
@bigbossman59695 жыл бұрын
u should have fixed it your self its not that hard to do
@TheKevinChannel15 жыл бұрын
Man my 16 Jk has 65k (yes i have a lot of miles due to work) and same side on the passenger head had them replaced 3 times. The 2nd time it they replaced the camshaft due to the lobe getting chewed. Now its going in the 4th time in the next week with the tapping.
@terrywaters61864 жыл бұрын
They supposedly came out with improved rockers so replace them all and be done with it.
@hecanseeme82105 жыл бұрын
Is this part of the extended warranty on the heads?
@mr.k50114 жыл бұрын
solid vid
@jimpie2313 жыл бұрын
Thanks......nice! Jim
@nasa70mmfilmpositives44 жыл бұрын
Thank you!
@LBYINCHINA4 жыл бұрын
How much does it cost generally at a shop?
@JWard23 жыл бұрын
Will it always come back even after fixing it?
@Xcentr1cK5 жыл бұрын
Thanks man. :)
@randy1ization5 жыл бұрын
seems to usually be the back though.
@schaeferschaefer26242 жыл бұрын
1:16 somewhere a Chrysler engineer is laughing.
@abdullahal-shimri30915 жыл бұрын
I have a 2017 Ram 1500 with this engine and 20k miles. I’m hearing this tick too! Will get it checked out by the dealer soon.
@robsmith25234 жыл бұрын
same problem with my 2018 ram 1500. dealer told me this is normal. am now going thru the lemon law with this problem. let me know how you made out with the dealer. thanks.
@abdullahal-shimri30914 жыл бұрын
rob smith dealer told me it’s normal! Your truck is still under warranty and so is mine. I stopped worrying about it.
@jamescole68464 жыл бұрын
I have a 2013 Jeep JK and a 2017 RAM. It's my 3rd RAM the tick is just there. Google HEMI tick, I finally ignored it. 1st two over a 100K my 3rd is only at 20k cause I drive my Jeep all the time :) but sometimes after I start and drive my RAM after sitting a few weeks it sounds like the engine is falling apart for a few seconds then it goes away. all 3 have done that. My 2013 Jeep JK 2D has 92000 on it and the tick does seem to be getting worse but I switched to 10W30 last year and it went away for the most part. It is probably the needle bearing as indicate and I saw a post above about dis-connecting the sensor on the oil pump to run full volume all the time. I am going to look in to that. hopefully that will make it last a bit longer. Mine is on the driver side aginst the firewall as well. that is where most of them start.
@ChromeForDays Жыл бұрын
My 2013 JKU is making this noise. Is the root cause of this that the oil changes weren't performed on schedule? I bought the Jeep used and it started shortly after I got it, so I have no idea if maintenance was done properly by the previous owner. Looks like I have a new project to do . . .
@elymark24 жыл бұрын
My 2013 just starting making this noise...I can't tell which side it's coming from. It has 240,000 miles on it, so I guess it's done fairly well. I should be able to feel the loose rocker once I gain access; or is there a dependable way to narrow down the location?
@zxtuner4lyfeАй бұрын
damn 230k. thats amazing with the 3.6
@tseeley486 жыл бұрын
I have replace 5 rockers on my 2012 JK. I also replace the lifters at the same time. the parts not expensive, if I recall the rocker was like $9 each and lifters were a little cheaper. what is strange is that all the JK owners that I know that have had this issues, the first one to go was the same one shown on this video, the second one in from the back on the top, or intake side. Other thing to note is while you have the valve cover off if any others are marginal, you can tell as there will be some wear on the outside of the cam lobe where the sides of the rocker are making contact.
@justindriskell94736 жыл бұрын
tseeley48 good points!
@whatevenisamedic5 жыл бұрын
My 12 jk does the same. Plan on fixing shortly...
@sonnyjeffers1564 жыл бұрын
My 2012 is currently getting all rockers and lash adjusters replaced by me . Is it possible to not remove the cams to get the adjusters out?
@voiceinwilderness74 жыл бұрын
Justin Driskell - is it necessary to even replace those tappet covers? Is it just purely cosmetic noise solution, or will it eventually cause a engine issue?
@justindriskell94734 жыл бұрын
Yes. The camshaft rides directly on that roller. I've seen where the rocker eventually scrapes the lobe of the cam off which will cause a misfire and requires even further engine disassembly to repair
@chrisguy92072 жыл бұрын
Do you get any engine codes with the tap… Just can’t get mine started… Can start with ethanol…
@ENG13INELT6 жыл бұрын
Wondering if the rocker arms are in need of a recall. My 2017 Grand Cherokee has the exact same noise with only 18,000 miles on it.
@justindriskell94736 жыл бұрын
Steve Davis with 18000 i would assume its covered under warranty. But I do agree a rocker arm redesign is needed
@pauljoey79774 жыл бұрын
Change oil at 3k with penzoil ultra 5w30. U wont have these issues
@Ubon945 жыл бұрын
I have seen alot of videos with Chrysler. Have they made any improvements in 2019 and up to fixed this? I thinking about buy a Durango or 1500 in the future .
@terrywaters61864 жыл бұрын
It's supposed to be fixed now. The old rockers were made in China and the needle bearings improperly heat treated, imagine that.
@DonSantos-xl1cz Жыл бұрын
Hi, how much does something like this cost to fix? Roughly what are we looking to spend?
@mmirek-dr2vq5 жыл бұрын
I appreciate your job . Do you have any problems with 2017 JK Pentastar 3.6 L ? Thanks Justin and Greets from France
@justindriskell94735 жыл бұрын
Thanks for your comment. I don't have much experience with the 2017 engines yet. If I had to guess, its not much different
@jrrincon795 жыл бұрын
Justin Driskell hey brother mines is making this noise on driver side I took it to shop n they said I have a misfire on cylinder 4 they change coil,plugs,n injector still feels little shaky
@googuser31455 жыл бұрын
Hmmm.... two stage oil pump? Runs in low pressure mode most of the time.... see a lot of rear rockers wear... furthest from the pump... I wonder😕