Jeep YJ Wrangler Rear Frame Rust Repair Kit Installation

Video describing the recommended procedure for installation of the Taboo Customs Jeep YJ Wrangler rear frame rust repair kit. Repair your rotten frame around the rear cross-member and shackle with this kit. P0399 P0604
To purchase the standard kit from the video please visit the link below.
www.taboocusto...
To purchase the standard kit including the bushing tube replacement kit from the video please visit the link below.
www.taboocusto...
Thanks for watching!
WARNINGS:
This kit requires an experienced fabricator/welder for installation. If you are not an experienced welder or you would not be willing to risk your life on your welds please enlist an experienced individual. Contact us may be able to help you get in touch with a qualified individual.
This kit is meant to cover most issues in the associated area however it may not fully cover all of the issues a frame may have in this area. This kit may not be sufficient to repair extreme rust issues. Again please enlist an experienced fabricator for this installation.

[@nealesmith1873]

Very good detailed video!

[@daveanderson8404]

awsome vid man, my jeep looks like that one and i want to tackle this job.

[@TabooCustoms]

Thanks!

[@DougsMessyGarage]

Looks like a well thought out kit.

[@TabooCustoms]

Thank you, we use what we sell and are always tweaking them for improvements.

[@markbelden6919]

Wow!! That's a pretty alright kit,

[@TabooCustoms]

Thanks !

[@djsuretay1]

Hey what size wire are you using and are you using gas

[@djsuretay1]

Are you using gas or flux and what size wire

[@markbelden6919]

Nice work and good information

[@TabooCustoms]

Thanks

[@12Bravojeepstuff]

After grinding clean the frame surface do you recommend any weld thru primer on the frame and plates? Would you also want to weld the openings in the plates were they over lap in spots on the frame?

[@TabooCustoms]

Sorry for the delay, KZbin was holding comments without notifying me we had comments.

[@TabooCustoms]

Yes if used correctly. With mig welding they can still cause welding issues with striking an arc and contaminants in the weld if you try to directly weld through the primer. Most of the weld through primer instructions will still require you to remove the primer in the area of the weld.

[@myrongaines5542]

Shouldn't u have primed the bare metal on the existing frame and the back side of the new plates before welding? Looks like that's going to rust between the frame and new metal inside out.

[@TabooCustoms]

Yes, we recommend using 3M weld through primer on the inside. This I think was one of our first videos so we missed some tips while getting caught up in trying to do a video. Hard enough doing rust repair, much less try to do a decent video when doing rust repair.

[@timeless6964]

Good Job!!....Looking for a Kit!!.....Thanks!!

[@TabooCustoms]

Any time!

[@scorpioviews]

How much did you have to invest to replace this area and what was the budget? - thank you for making this video! im surprised only 3,000 views.

[@TabooCustoms]

Sorry for the delay, KZbin was holding comments without notifying me we had comments.

[@TabooCustoms]

The price of the kit is below $100 so in $ its not a lot if you have the expertise in welding and the equipment to get it done. If you have to take it to a shop expect to pay another $400 or so for labor.

[@gdtengine3935]

What are the shackle bushing tribe dimensions? Where did these come from. Great video thanks for sharing. GT

[@TabooCustoms]

Sorry for the delay, KZbin was holding comments without notifying me we had comments.

[@TabooCustoms]

We make the shackle tubes ourselves, the bushings come from Daystar. The tube is roughly 2.75" long with an inner diameter of 1.25".

[@jamesdjesse]

Cou!d that be done without removing gas tank? My YJ has a tow hitch welded in a way that prohibits the tank from being dropped.

[@TabooCustoms]

Sorry, for some reason KZbin had your comment as "held for review" and I didnt realize it. I would not recommend it, it really needs all the pieces to be effective and there is no way to weld the inside piece with the tank still in there....other than maybe removing the tub.

[@bdc7273]

Is doing this on the TJ easier? Also, are you able to cut the out the rust if wanted? Will it cause any issues?

[@TabooCustoms]

On the TJ it is easier, you do not have to deal with the shackle mount in the middle of the frame. I also find that removing the TJ gas tank is a little easier than the YJs. We have a kit now released for the TJs in this area. Thanks Dave B www.taboocustoms.com/store/tjrearframerustrepair

[@hayzersolar]

now what about the xj you make money in that area. i have fix 2 xj with frame issues. they rust almost in the same spot

[@TabooCustoms]

Currently we dont have rust repair kits for XJs, maybe in the future.

[@aidannunan7164]

I only have a 2 in long by 1/2 in tall hole behind the bushing on both sides of the frame on the driver's side, could i cut the the bad frame out and put a section of the kit, in stead of welding over?

[@TabooCustoms]

Sorry, for some reason KZbin had your comment as "held for review" and I didnt realize it. You could yes, but what you will probably find is that when you start digging into it there will be much more rust than you realize.

[@randyhoover7399]

Do you have kits for EJ Grand Cherokee Laredo?

[@TabooCustoms]

No sorry we do not.

[@scorpioviews]

how many hours did it take you to replace something like this?

[@TabooCustoms]

Sorry for the delay, KZbin was holding comments without notifying me we had comments.

[@TabooCustoms]

Depends somewhat on how easily everything comes apart. If everything comes apart without trouble I could see it done in 4-5 hours.

[@johnWilliams-pl8vm]

Nice is worse how many hours does it take for both sides

[@TabooCustoms]

I plan 6-8 hours total, taking fuel tank out and repair.

[@randyhoover7399]

How much rust is to much?

[@TabooCustoms]

Difficult to say, a lot depends on where it is. I normally say that if you have .5-.75" of good material from the top of the frame our kits will usually work.

[@skyfual]

Why is there no comment on this?

[@timfarley274]

I'm in the midst of dealing with bolts that are spinning, bottom line, these auto companies are staffed by idiots with "Engineering" degrees, and there is a reason they will once again need a bailout, they cannot seem to design for servicing with over 100 years of production experience.

[@TabooCustoms]

Sorry, for some reason KZbin had your comment as "held for review" and I didnt realize it. I have worked in the OEM and aftermarket auto industry for 20 years (not including Taboo Customs time). Honestly beyond the warranty period I would say from a company perspective they dont really care. They dont want you to keep a vehicle for ever.

[@timeless6964]

Good Job!!....Looking for a Kit!!....Thanks!!

[@TabooCustoms]

Any time!

[@timeless6964]

@@TabooCustoms ...What would You charge for a Typical YJ Rear, Both Sides??....How Long of a job is it-1day-2days??