No Paper Message in MFC-7360,DCP-7055 Brother printers

[@sarahdenkert3780]

I know this may not be seen because it is 7 years later, but THANK YOU! I had watched other videos and you were the only one that showed lifting the gear up for the new cam lever to fit correctly! That was what I was missing, and now it works! I fixed job's printer thanks to you! :)

[@brotherprintersupport]

You are seen😊 Thanks for the comment.Hope you subscribe this channel also.If any other problem are there just leave a comment.I will try to fix it on the video

[@Kevin-ve5rr]

Nice video. Have my printer for 7 yrs, worked like a charm until the gear splitted. Brothers put down a flimsy gear on purpose but this video gave my printer a new life. Thanks.

[@uredskivid]

I just replaced my cam lever . I need to add that this is easy to do , but be aware that the little broken off piece needs to be fitted after you raise the gear and you must lightly force the new tab into the semi circular slot . Mine works great now , THANKS for this video !

[@shaheenpierre]

Thank you for posting, would never have figured this out. This saved my MFC-7360N, almost bought another printer.

[@brotherprintersupport]

kzbin.infoitQb9iksI_Y?si=NBDmqkoPgusfgZi2

[@OlegOsovitskiy]

Thanks! I have the same problem on my MFC-7360N after only printing 480 pages! Incredibly bad design. This video saved me from buying a new printer. I ordered a couple of these CAM levers on amazon (2 pieces for $9), will fix my printer when they are arrive. Thanks again, a good job!

[@kruzli7255]

Thank you so much for uploading this video! It saved me a few hundred dollars. We tried so hard to figure out what’s wrong with the printer but nothing helps until I found his video. I just purchased the cam lever from Amazon for $7 to replace the broken one.

[@brotherprintersupport]

Thats great bro.Plz subscribe my channel also

[@storonto5355]

Hello, could you share the link on Amazon?

[@insulwiseenergycomfortsolu3293]

I CAN'T imagine why someone gave these guys a thumbs down?! This video SAVED me. In my case the white plastic cam lever part was not broken, but had somehow fallen off the "post" that it pivots on. I had accidentally pushed the cam lever too far to the left when I was attempting an earlier repair method, and that's how it came off the post that it sits on. I did not know how to take apart the printer in order to get access to it. This video showed me how to do it properly, and then properly re-install the cam lever onto the post so that it pivots properly again. Seems like a bit of a design flaw, but as long as I was able to avoid junking what was otherwise an excellent laser printer I am happy as a clam! Well done gentleman!

[@brotherprintersupport]

Thankyou for your appreciation.Plz subscribe too and feel free to ask for printer related problems😉

[@jlbrazee]

This is awesome. Phone's rotated wrong, I can't see half of what you're doing, and you almost forgot to put the spring back -- and yet I totally fixed my printer for $1 because of your work. Thank you.

[@brotherprintersupport]

Creative Username thankyou

[@farakhzaman2453]

Part just replaced and worked exactly as shown on the 7860W as well. Just ordered the part off ebay and it popped in with a bit of coaxing. Had a bit of difficulty seeing what you were doing in the video with the clasp but once I got that figured out it went pretty easily. Thanks again! Saved me several hundred dollars in a printer replacement.

[@FranzJosephGC]

This is the most useful video I've seen so far on KZbin. It literally saved me 60-150 bucks. Thank you guys so much

[@nhivu4666]

Thank you so much for this video. You've saved me from spending $150 in repair. I was even thinking of throwing the printer away because it costs just a little more to buy a new one. But it would be such a waste only because a small plastic part is broken. Thank you!

[@brotherprintersupport]

Welcome Please Subscribe my channel

[@ericbickerton]

So glad I found this video. I bought a replacement feeder cam lever and installed it a few minutes ago. Worked perfectly. Thanks!

[@shredkrum906]

I just completed this fix today! I got a $10 replacement part on ebay w/free shipping, and it took me about 15 minutes to get everything swapped out. Works perfectly! Thank you!

[@Ric-go9rq]

what is the item number for this part? or can you send m the link to buy it? Thanks

[@brotherprintersupport]

Shred Krum Laurence Marks if you have any other problem on your brother machines please do let us know inthe comment section.Just write the error message and model number of the machine

[@userbituniversal9442]

Amigo pasanos el link porfabor , quisiera comprar esa pieza

[@TerryMosher83]

So happy to have found this video as it allowed me to fix my printer for just a few bucks. Make sure that the tiny little white tab (the part that broke) goes through the little curved space in the black plastic at the bottom as he shows in the video otherwise you will continue getting the error.

[@brotherprintersupport]

Terry Mosher thankyou....please subscribe

[@alanadiaz]

It took me a while to get the little tab in that slot. I was afraid I would break it if I put too much pressure. But it went in with just a little bit of pressure. Fantastic! I had given up on this printer. But now it's working properly again! Thank you so much! Paid $7.50 shipped on eBay!

[@brotherprintersupport]

Alan Diaz thankyou for comment

[@brotherprintersupport]

Terry Mosher thankyoufor your comment.Please subscribe

[@denisebarlow5795]

Got the piece from Amazon and my son had it working again in 15 minutes. Thanks for this helpful video. Too bad Brother does not discuss this problem and fix. Thank you!!

[@brotherprintersupport]

Denise Barlow plz subscribe

[@mhzellers]

Your fix worked for me. I did have a little trouble getting the case open and the clutch off. Those parts could have been better demonstrated in the video. As others have said, your video saved me the cost of a new printer.

[@brotherprintersupport]

Mark Zellers thankyou soo much.Appreciate you if you subscribed

[@SeanCameronUK]

This fixed my paper feed. I'd tried the brother's troubleshooting, I tried changing the rollers, but it was the piece all along. Thanks for your help!

[@kambo_trick3y89]

Extremely useful video this helped me to repair my printer hope you never take this down

[@brotherprintersupport]

Thanks.Plz subscribe

[@cherylhageman2922]

Thanks for the video! I found a feeder cam replacement on Amazon and followed your instructions in your video and now my printer is fixed. Thanks!

[@brotherprintersupport]

+Cheryl H thanks to you too

[@hennerv.2305]

I also want to say thank you! With the help of your video and a simple spare part I was able to bring back the paper feed functionality of my printer. Great work, thank you again for this helpful video!

[@hughallen3451]

Thanks for posting the video. It helped me fix my printer, saving me lots of money and built up my confidence to do other basic repairs.

[@mistyinltown79]

Thank you for this, I found another video showing the lever can sometimes move, but mine was broken, thanks to you I spent $5 and fixed it myself in like 10 minutes! Thanks!

[@khanshehzad9233]

thanks a lot for this video , when i want to repair any thing , i watch always youtube . your video is realy very very help full and eaysy to follow. thanks again.

[@taskintuna2502]

Hello all! Thanks a lot for this amazing help, which I could not get from Brother... although I am very sure that this weak point is known! You saved my printer and also nature because I did not have to throw it away!

[@brotherprintersupport]

Thanks bro.I need ur subscribe button clicked plz😉

[@dannyaiz]

Thanks for the video. Mine wasn't even broken, just out of place. I pushed it back in and problem solved.

[@SP-fp6kc]

Hi guys ! You don't need to replace whole part , only one thing what you need is locker washer with inner teeth for static shaft where fault part placed. After locker washer placed properly on shaft tightly, lever is fixed solid in horizontal position. I'm fixed my 7360N with it, so wish to you! Respect to all tech minds;)

[@brotherprintersupport]

Congrats .That can also be done

[@lukadaft]

thanks, worked perfectly for me this way. u helped me so much, thankssssss

[@AndreaMagro88]

Thank you so much for this valuable video. You solved all my problems with a minimal expense.

[@JoeZemel]

Thanks very much. The $3 part on eBay and your video fixed my Brother HL-2270DW.

[@annathecook]

Thank you so much for this! Saved me hundreds. This little piece is like $13 .

[@huiyu5279]

Thank you so much, I almost throw my printer, I found your video, and I have the same problem, ordered the part, you save my printer! Many thanks!!!

[@brotherprintersupport]

thanks .plz su subscribed

[@alexlotta]

BIG THANK YOU MAN, i saw from another video but yours is before the one i saw so MUCH APRECIATED too wish you all the best from my heart , it was really helpful

[@toprefilling3617]

first of all thanks for the video, but I am with some other viewers here, nowhere to find the parts, after refereed to other sources, I figured it out u can reuse the broken plastic parts but dump the spring parts, the trick is after having reinstalled the broken parts to its original position, just snap it to the left a little until u feel a slight click, then u can try printing something to make sure, this is worked on my MFC-7460.

[@FranzJosephGC]

Yup, I also just used the broken one and it seems to work. I did order a replacement on Aliexpress for less than US$ 2 though.

[@enriquevasquezplaza1165]

2nd time in 6 years, fixing now the 2nd printer. Life saver!

[@brotherprintersupport]

bro plz subscribe my channel

[@shenjiming]

Really appreciated. I fixed my similar issue on Brother MFC7860DW with this video.

[@steved1196]

Wooden wedge FTW! And thanks to this vid for the insight. My printer will live on for another couple of years.

[@brotherprintersupport]

plz subscribe

[@thomasoconnell4997]

You guys are the best! 12 bucks for the lever on ebay and wham!...in business. Next time I am in Mumbai I will buy you a drink at Leopold.

[@brotherprintersupport]

Thomas O'Connell thankyou but I am not from India.

[@MakeItEnough]

So glad I found this video because I was able to see a comment below for another fix. It works with a folded up piece of paper or cardboard too!

[@JorgeAlbertoMahechaRodriguez]

Amazing video, thanks a lot. I ordered the part for USD10 on ebay, did exactly what you showed and I have my printer back. Great job!

[@laurencemarks2833]

Wonderful. This same problem occurred on our HL-2270-DW. The cover removal is different (no screws, two catches in the back, one in the front), but the mechanism is exactly the same as shown. And the failure was exactly as shown. I found three eBay sellers and ordered a pack of two from one of them, as I expect to have this problem again in a few years.

[@brotherprintersupport]

Laurence Marks if you have any other problem on your brother machines please do let us know inthe comment section.Just write the error message and model number of the machine

[@laurencemarks2833]

The (minimal) error lights on this printer led me to believe it was a drum issue. Error light on solid, no other lights. A different drum gave the same error. I scoured the 181-page Brother Service Manual for information on this and found nothing. I installed the Brother Service Monitor software and connected via USB instead of wireless and dumped the error log and it said "Paper Empty" although the paper tray had plenty of paper. I should have gotten the first clue--that each time it started printing it pulled paper 1" (25mm) from the paper tray before stopping. So I knew it was a paper feeding problem and cleaned rollers to no effect. I never would have figured out that the problem was the paper cam lever without your website. Thanks again for sharing your knowledge with the rest of the world. I bought two levers for $15 on eBay so I'll have a spare a few years from now when it happens again. This part is definitely underdesigned.

[@brotherprintersupport]

Laurence Marks sometimes small things create huge problems.And we go crazy after it.Anyways thanksfor your comment.If you have any other issue just let me know

[@MeineMeinung-rt5qn]

Thank you very much. Now my brother MFC-7630N is back to life.

[@brotherprintersupport]

Thankyou foe the comment.Hope you subscribe and share my channel🤗

[@mountainmark9947]

Thanks dudes. Your vid helped me identify problem. Unfortunately, I wasted many hours cleaning the paper feeder rollers before finding your fix.

[@brotherprintersupport]

Mark B thanks for comment bro

[@brotherprintersupport]

+Mark B thanks to you as well bro

[@brotherprintersupport]

Mark B Laurence Marks if you have any other problem on your brother machines please do let us know inthe comment section.Just write the error message and model number of the machine

[@brotherprintersupport]

Please subscribe

[@airborne13579]

I fixed mine. Hooray. Thanks to the video. However, it took a while to figure out how to get the side cover out. Also the the plastic pieces need to be pushed down more so the small piece (the easily broken part as in the video) need to get into the slot/channel.

[@brotherprintersupport]

Plz subscribe😉

[@tonyohcookingshow]

Of the several videos I watched, your really helped me. Thank you. Tony fron San Diego :)

[@brotherprintersupport]

KIindly please subscribe my channel also.And if you have other queries please leave a comment😊

[@frotz661]

Did you find a service manual anywhere on this?

[@lukadaft]

You guys, you, are my personal heroes.

[@helpfixmycomputer1]

THANKS. Any thoughts about about a permanent fix by placing either rubber O-Rings..or metal retainer clip around the top of the cam lever of the dow to keep the lever from sliding out? The peice of the cam that breaks off is nothing more than a guide that wears downs.

[@Transmission4less]

Thank you for the video , got mfc-7860dw and found it has the same problem so I used super glue with hot air to melt all together and formed strong thicker edge than factory, worked well, yes to put back was not easy but figured the mechanics of how it works and all in, I found that you can preload this part with a spring pushing to stay all the time inside will fix it for good even with that small edge is broken, Thank you for sharing.

[@brotherprintersupport]

Please leave your question regarding issues in any brother printer.We will help

[@huaixianke4877]

you mean, even the small edge is broken, it is still working?

[@Transmission4less]

the purpose of the edge is to keep the lever in place not to slide back, you can simply melt plastic and build stronger edge as I did or find a suitable spring loading it with a screw from the back to keep it in place all the way inside. open it and will figure what i mean. if you heat it with hair drier will just melt and u can shape it , maybe that is better and much starlight forward solution. even replacing it with new one is not good enough as it is still weak better build the edge stronger yourself.

[@huaixianke4877]

Salim Safran thank you for response,actually i have took out the part already, however the little portion of the parts was break up and fall off when i was trying to put it back,the reason i asked the question,above was because when open up the right panel, first thing i saw is disk-like part was not clipping the black stick, so i was thinking that maybe the feeder elever was not cause of the no paper error...and yes, i just broke my printer...

[@Transmission4less]

yes it not easy to put it back but if you make thicker stronger edge you will be able to push it slanted and might bend but wont break. new one most likely will be broken again during installation as it is very weak really bad design to such great technology machine.

[@aaronabedin3256]

where can I find this feeder?

[@kellyvillegas4824]

Great explanation and demonstration! I was able to do this myself. Thank you gentlemen!

[@brotherprintersupport]

thanks bro.Please subscribe also and feel free to ask about any printer related problems.I will try my hard to fix ur issues

[@TheArecf]

Thank you for this video. Saved me from discarding my printer. More detail with regard to how to remove the side cover would be appreciated.

[@brotherprintersupport]

Pls subscribe

[@DavidAlanArnold]

Great Demonstration! I wonder if that's what is wrong with my printer! Paper moves a bit, but does not leave the paper tray. If I slide the paper forward just a bit, the printer feeds and prints.

[@edsc86]

Yep, exactly my problem and yes this is the part that was broken

[@sithlordsoup]

3:11 this procedure alone may want you to get buying two feeder pieces just in case, when you press through there’s a chance that tooth (basically the whole reason for this replacement) will break off. Thus causing you to throw a fist through a wall.

[@mcardenas23]

I have the hl2280 and I reinserted the same part and it works! Didn’t need to order a new one, so try reinserting before you order.

[@FallenAngel-qp3nl]

Good job! You just helped alot of people! God Bless You....

[@brotherprintersupport]

Plz subscribe

[@FallenAngel-qp3nl]

@@brotherprintersupport oh sorry bro i just did

[@paulpadda2456]

Thank you so much this worked for me. I was seriously contemplating throwing out my MFC 7460DN printer.

[@suryapalagiri5664]

Thank's a Ton sir this video helped me a lot very short and simple and fixed the problem once again keep up the great job !!

[@naterh]

This video helped me identify and fix the no paper problem with my Brother HL-22400 not once but twice. I found the Brother Feeder cam Lever, LY2579001 on Amazon. Thanks!

[@brotherprintersupport]

naterh plz subscribe my channel

[@patriciaarmstrong246]

wgat are you doing on the right hand side to disasemble? I can't get pass your second step. Hope I can go further. Please help!

[@naveenchandra6526]

For those who couldn't find a spare lever remove the spring and just add some paper behind the lever to hold it in place such that the gears are connected. This lever acts as a clutch and stops a roller from running when there is no paper tray inserted that is all. I couldn't find stock for the replacement after searching on multiple websites in my country. Just add some paper behind the lever such that the gear is lifted and connected to the longer roller shaft. (the opposite direction the spring is holding, so you can remove the spring or keep it, it won't matter cus its always connected now. I hadn't been using this printer cus I didn't want to manual feed paper every time. Now that it is fixed I can easily print, and fuck inkjet and their costly cartridges.

[@zwterrible]

This little paper fix is great for my "old" MFC-7860DW, and you don't even need a new lever. I actually got a lever off ebay which seemed intact and replaced it, but for me (just as in the video), the new lever did NOT elevate the gear into place unless held there (and reassembled with paper in the tray, it still said "NO PAPER," presumably because the paper was not pushing it into place). I probably didn't put it in right, but whatever, your paper trick to hold it in place works great. Thanks for the practical suggestion! Right on with the cartridges... I do kinda like the new color lasers though

[@naveenchandra6526]

Glad it helped

[@eddieennisbaysal27]

can u post some pics of it about paper putting baCK

[@micheljourdan3241]

worked for me, thank you very much.

[@Ivywire]

Thanks for this. Brother Printer should say thanks, too.

[@itsumonihon]

Very good video. Thank you for uploading this to youtube, you are nice guys. Good work!

[@MrAesir1]

BOOM.. you saved me from throwing my printer away!!.. Ha! Cost me 32 cents and following you advice.. thanks so much!

[@brotherprintersupport]

Colin Johnson Laurence Marks if you have any other problem on your brother machines please do let us know inthe comment section.Just write the error message and model number of the machine

[@brotherprintersupport]

Colin Johnson thankyou .please subscribe as well

[@prettipcservices]

do you have any experience with HL-L2380dw? same error: No Paper Reload paper in Tray. I have not disassembled it to see if i can find a 'feeder cam' inside it.. yet, but I imagine they're all quite similar on the inside.

[@brotherprintersupport]

Just chk the feeder cam...this all are similar machine

[@rafaelrodriguezsierra316]

What’s is the name of that little part of the printer?? Feeder gun??

[@brotherprintersupport]

feeder lever part no Ly2579001

[@michaeljlumpkinesquire]

Thank you! Took about 10 mins once I got the cover off!

[@brotherprintersupport]

Plz subscribe

[@mannymccash9660]

do you have any video for this problem with the HL 2270 series? thanks

[@brotherprintersupport]

plz send me the error code

[@brotherprintersupport]

Send me error code from the display

[@nashvillecustomclosets3021]

@@brotherprintersupport there is no "error code" that we can find - it just doesn't take the paper, and the (normally) green light goes off, and the orange one next to it goes on - and stays on until we press the regular button again (if that makes sense)

[@brotherprintersupport]

@@nashvillecustomclosets3021 first Switch on the machine and on standby mode press the GO or Green button 3 times fast.Thia will print the settings of your machine.Check in the settings Toner Replace Mode.Continue or Stop.The problem you are getting is may be due to the Toner replace mode in Stop.If the mode is Stop again return to standby mode and press Go button 7 times fast.This will change the mode to Continue and you can now print normally

[@nashvillecustomclosets3021]

@@brotherprintersupport I will give this a shot thank you so much either way!

[@farakhzaman2453]

My brother 7860dw printer was having the same issue. Found the same part on ebay for 10 bucks...just ordered so hopefully it arrives in a week and I can fix this thing. Thanks!

[@rosstherooster]

I have a Brother MFC9325cw. Will P/N LY2579001 be compatible with my model? This is the only P/N I can find that's being sold anywhere online.

[@brotherprintersupport]

I will chk and confirm you

[@artstewart3757]

Thank you for posting this very helpful video. Upon replacement of the LY2579001 Feeder Cam Lever, the printer will feed paper once, paper feed issue returns on subsequent attempts. I have repeatedly removed the side cover, subject component to confirm replacement cam lever functions properly, printer will again feed - ONCE - after each assembly and disassembly. I then attempted to print with the side cover removed. It appears that the gears engaged (lifted) by proper positioning of the cam lever are spinning, shaft on which clutch is mounted appears to rotate freely, wondering if it could somehow be related, or perhaps another cause. I would be most grateful for any guidance.

[@brotherprintersupport]

Thankyou for support.Please let us know you have any other issues related to brother ptinter

[@brotherprintersupport]

Please subscrbe also

[@2991scot]

Dude you're awesome!!! This saved me a big printer replacement. Thanks!

[@brotherprintersupport]

Canadian Mafia thankyou so much...if you have any other issue please comment below and please subscribe

[@isma-aechelong4552]

Thank you so much for this video, from Thailand

[@brotherprintersupport]

You are welcome brother.Can you plz subscribe?

[@aliulameer9534]

Thanks, what is the name of this platic part, and where can I get it ?

[@brotherprintersupport]

Its feeder cam lever.Check in amazon

[@brotherprintersupport]

LY25790001

[@burmajames385]

@Everest Gaming, is there any other reason for the NO PAPER error message? I purchased a new feeder cam lever and replaced it per another instructional outube video (with same demonstration as yours--thanks to you both!

[@brotherprintersupport]

You may have problem with your paper tray or feeder clutch.Please replace both and check .

[@burmajames385]

@@brotherprintersupport thanks for the suggestions. I'll check them out!

[@ADAMTHEGREATNESS]

where do you find the part? thanks

[@tonyend2001]

Thak you! This resolved the issue with my MFC 7860DW.

[@wilddiode]

Thanks very much! Didn't think this would fix my problem, but yes. Amazing.

[@brotherprintersupport]

wilddiode thankyou and if you liked it please dont forget to subscribe also..thankyou

[@rdbacongan1678]

is this video can also fix DCP-L2540DW?, i have the same problem "tray jam" i already try different ways of cleaning and fixing but still error occur

[@brotherprintersupport]

No 2540 has no lever

[@AbhishekSebastian]

Thank you. It worked! That was exactly the problem. Mine was not completely broken but out of its place. It broke however while trying to put it back in. Luckily, mine still works..! :)

[@joeschmoe4030]

Worked like a charm! A $10 fix, Thanks!

[@brotherprintersupport]

Joe Schmoe please subscribe

[@idrhys]

Hi, where can we procure that piece that you just replaced? Just found out that it is the same broken piece in my printer making it not feed paper. What is the part called or number? Thank you so much for your video!

[@idrhys]

I found this on EBAY. Do you think it is compatible? www.ebay.com.au/itm/LY2579001-Feeder-Cam-Lever-Brother-HL-2130-2220-2240-2250-2270-2280-DCP7055-7057/132764083534?hash=item1ee95b254e:g:cqoAAOSw2KRbiNlO:rk:1:pf:0

[@brotherprintersupport]

@@idrhys yes this is the same part

[@idrhys]

@@brotherprintersupport Thank you so much again! bought the part from ebay for $9AUD and fixed this in less than 15 minutes! The video is a bit shakey but still great! Thank you!

[@storonto5355]

Where to buy the replacemwnt of this damage part?

[@brotherprintersupport]

It depends upon where you are.search in google for brother support near you

[@brotherprintersupport]

Plz subscribe😍

[@chadwce]

Thank you for your video it was very helpful.

[@brotherprintersupport]

Plz subscribe

[@alejandroaparicio1261]

68/5000 excellent tutorial solve my problem thank you very much for the help

[@yananh]

Great video! I thought it was the pickup roller first. It turned out to be the white plastic part you mentioned in the video. Will you advise the name or part no. of this plastic part? Thanks.

[@brotherprintersupport]

its feeder cam lever

[@yananh]

jeevan luitel Thank you.

[@ccutube1910]

Thanks for this useful video! My printer is working again. And that part is the weakest piece of junk!

[@brotherprintersupport]

ccutube1910 plz subscribe

[@jeanpopwell4016]

Used a highlighter cap to keep the Cam lever permanently engaged, fits perfectly!

[@brotherprintersupport]

plz subscribe😉

[@neerajthakurvlogs5977]

My printers sometime pick the page and sometimes not what is the problem?is that the same problem to replace feeder cam lever or anything else please reply

[@brotherprintersupport]

Whats the model?

[@HH-qh9ie]

Hi Jeevan, Where could the part be bought from? I tried to obtain it online but the more I looked for the less I found.

[@brotherprintersupport]

you can find this part only in authorised service centers.Check brOther support online

[@minglong9398]

Authorised service centers don't sale parts to the individual customers. They can fix for you and charge more

[@brotherprintersupport]

Not Like that Bro.Take it easy

[@vanessalin3193]

You can buy it here for $9 www.iteminconline.com/ly2579001_ly2579001-brother-hl-2220-feeder-cam-lever.htm

[@vanessalin3193]

Oh here www.partsimple.com/ly2579001-bro-n-13.html but you would have to buy 24 of them ... maybe not a bad idea since this was such a poor design. Ive just tried super gluing the existing cam lever.

[@jrossofskb]

Where can I purchase that part for a MFC-7860DW?

[@brotherprintersupport]

Joseph Ross you can buy in ebay or any brother printer service provider. Part number is Ly2579001 Feeder Cam Lever

[@brotherprintersupport]

Joseph Ross please subscribe my channel and let me know what other probem you have in brother printers

[@jrossofskb]

Thank you!

[@jrossofskb]

Ok, subbed!

[@jrossofskb]

Thanks to you I was able to fix my printer!

[@mufer9]

What is the name of this part that you replaced ? Where to buy it ? Many thanks

[@hectormauriciohernandezgon4090]

Wonderful. Could you tell me what is the name of the part please ? im from Mexico and i have the same problem.

[@brotherprintersupport]

Héctor Mauricio Hernández González part number is LY2579001 FEEDER CAM LEVER

[@valentinoromano6795]

Hi, I also have the same problem, this spare part LY2579001 is compatible with Brother dcp-7057?

[@brotherprintersupport]

Valentino Romano yes..its compatible

[@ronenfe]

Thanks, I had the same broken part. I tried to use super glue but it wasn't holding it. I put everything back until I order the part. Strangely it started feeding papers even with the broken part.

[@stephanelarrieu5674]

Many thanks, my Brother works again. +++++

[@JHERNANDEZ4899]

hello good afternoon, sorry that number and name of part is that you replaced?

[@brotherprintersupport]

Feeder Lever cam Ly2579001

[@vicliu2414]

I did replaced the broken parts exactly as your video showing, turn power off and on, but it still has no paper error message. What else can I do?

[@brotherprintersupport]

vic liu may be you have not fixed properly or else there may be problem of the pickup rollers or sensors

[@robert-fl9dr]

Thanks sir fr ur video it was so use full,can we fix the same broken part will it work.

[@brotherprintersupport]

robert rt broken part must be replaced for better performance

[@minglong9398]

Thank you for your video jeevan luitel. My mfc-7360n printer got problem with no paper errors. when I follow your instruction to open it, the same parts broken. But I can't order that parts from Brother's service center.

[@brotherprintersupport]

You r most welcome Sir

[@techstuff786]

Thank you very much just fixed mine!!!!

[@brotherprintersupport]

Please subscribe the channel.I have to reach 1K

[@techstuff786]

@ done

[@novieledesma9645]

Is the part available in the phillipines? Even in brother service center? All seller of the said part are based in the US? I have the same problem as yours. Thankyou and Godbless

[@brotherprintersupport]

Novie Ledesma it is available in philipines

[@novieledesma9645]

Technical Center do you know any specific shop? Or just in the service center? Is the service center selling parts even though i dont have any proof that i have printer, i dont have receipt or any, just the printer. Thanks

[@brotherprintersupport]

Just ask for part number Ly2579001 feeder camlever

[@novieledesma9645]

Technical Center there is someone offering me for 10 bucks, he said that he can fixed it for long term. For me not to purchase the said part every now and then. Also, he will teach me how to fixed it. Do you have any idea on what he is saying? Thankyou

[@novieledesma9645]

Technical Center just wanna share this to you. I dont understand the language. But this is the solution for the problem, so that we will not spend too much money for the parts. We just need spring. kzbin.info/www/bejne/q5TZdo1joZqbi7s

[@hectorcastro8136]

can you crazy glue it back together?

[@corujabuho8253]

Well done, Sir! Much appreciated.

[@brotherprintersupport]

Plz subscribe.Help me reach 1k😉😉