【加工動画60】樹脂に転造ローレット/Knurling Plastic.

[@gerogudo]

こんなにキッパリ加工してもらった樹脂は他にないのでは。 うーん気持ちいい❤

[@geoffankrett7012]

Your work is so clinical and precise, it's a pleasure to watch

[@MudSharkDanceLesson]

you're still my favorite machinist on youtube 😊 i need you to train the other youtube machining channels on how to set up their cameras/lighting so their videos look as good as yours 😆

[@301069patxe]

Whenever I could, I avoided having to turn technical plastics. They seem easy, but they have their little complications... I never had to knurl any of them. And having the tool tilted 2-3 degrees surprised me. Good finish. Congratulations.

[@jackfromthe60s]

How did you work out the knurling tool angle? I was hoping he would show us that, but I didn’t see it.

[@301069patxe]

@@jackfromthe60s The degrees are not seen in the video, it is my assumption, I would not give more than 5-6 degrees

[@SwaplampJapan]

Thank you for watching. Set the inclination of the knurling wheel so that the right end does not touch the resin during machining. Resin deforms greatly, so if you process it at a small angle like iron, the resin will suddenly be released from the right end of the knurling wheel and cause scratches. Gradual release of resin from the flat part of the knurling wheel creates a scratch-free knurling. Therefore, if you want to make deep rough knurling, you need to increase the slope.

[@jackfromthe60s]

Nice knurling. 👍

[@alexandreassmann4507]

Tomar café da manhã , vendo um trabalho de recartilhado (knurling) perfeito , é muito mais saudável e inspirador do que ver as notícias atuais... obrigado pelo vídeo ! 🙏🏻🤝

[@SerGsHobby]

Приятно смотреть на Вашу работу! 😊

[@__HJK__]

Я всегда думал что на пластике невозможно сделать накатку. Завтра попробую на POM и PA6, спасибо большое.

[@Georges-MILLION]

Très belle pièce , bravo !!! 👍👍👍

[@Darkrif1957]

Beautiful as Allways

[@mr.ranyhomemade2466]

Hi my friend how are you doing? Seen too long haven't post. Nice to see here 😊😊😊

[@parnuzutech]

good job👍

[@trialetcompagnie4481]

Nice job 🤩🤩🤩👌👌👏👏

[@saturnpss]

Perfect 👌

[@Alejandromundial.]

Muy buen trabajo 👍

[@richardorsulich4698]

Thank you

[@KSMechanicalEngineering]

Very satisfying

[@zumbazumba1]

When cutting knurling with a single wheel its important to support it with tailstock-its a material deforming operation that takes a lot of force.Always do it in one pass if possible.If you need multi pass remember -knurling is like thread making.You need to set the wheel in a pitch of previously knurled surface by hand -dont forget the backlash you lathe might have,to eliminate it let the carriage run forward under feed rate for a bit before setting wheel .Other vise it will cross knurl and it will look absolutely ugly,this is most common mistake people make. When you are done with first pass -clean surface before doing second pass. Same goes for multi wheel systems if you repeat cut make sure wheels are in pitch. Starting area will mostly look ugly so leave some extra material.

[@jackfromthe60s]

Good points, but this knurling was done with two wheels.

[@bearsfromspace]

that's class, bro

[@joestill3106]

Excellent work as always! Can you still buy good quality tools like the chamfer and radius cutter you used in Japan? I like that old style of tool but it’s gone out of fashion over here.

[@SwaplampJapan]

Thank you for watching. The chamfer and semicircular high-speed steel cutters used in this video are still made in Japan and are still being sold. However, the price has increased three times compared to the old days, and the quality has dropped considerably, so I have decided to buy items that were stocked by factories that are going bankrupt at low prices at auction.

[@Ironman9665]

Отлично. Интересно,для чего такая ручка?

[@SwaplampJapan]

Спасибо за просмотр. Это ручка рычага.

[@ambrest95]

Прыгажосць!)

[@塚本和也-o5n]

😃👍

[@uocMat]

❤👍👍👍

[@Noorikon]

👍👌

[@mekanikatolye4083]

Cıvıc eg vites topuzu.

[@ranospantsnikitos1957]

Максимально странные режимы обработки капролона. У меня стаж более 5 лет. Нужны больше съем, и подача. Стружку мотать не будет, она будет улетать. Удачи!

[@__HJK__]

Хах, мне наоборот нравится сливная стружка - из полиацеталя паралельно обработке наматываю мочалки для бытовых нужд - намного лучше того что можно купить в магазине. В общем, отходы - в доходы.