Jisulife Life7 Unbox and Teardown.

[@gregstarr2954]

Great job! Your sacrifice, our gains! Thanks dude

[@BXT_LAB]

Thank you very much bro!! 😎

[@がうるくら寿司]

bro how did you remove your screws that easy? mine is so loose it wouldn’t move no matter I turn it

[@jarosawskrzypek1373]

Great stuff that you make, thanks! Which of the fans you tested is the most silent on the first gear/level? Can you give one example from handheld and small desktop fans? Many thanks!

[@BXT_LAB]

The quietest handheld fan on the lowest speed that I have used is the one with the RPM display (which is in my other video). If you need a quiet Mini desk fan with quite a strong wind, I recommend the Funme desktop fan.

[@sidestep30]

In your opinion, which one is better overall Jisulife Fan Life7 or Orashare HF03 Pro? I'm planning to buy one and can't decide which is better.

[@BXT_LAB]

I will choose JisLife for better quality and the % screen on Life 7.

[@SERWELASZAIRAJEANB]

Hi, can I ask where you bought the lubricant for Elesi?

[@BXT_LAB]

You can use every normal mechanic grease. It's ok.

[@SERWELASZAIRAJEANB]

@BXT_LAB ok thank

[@brixmalimban4877]

Hello i bought a mini fan from jisulife and it was the life 4. I accidentally dropped it and now it's malfunctioning. When It goes to lvl 3 it goes 0% really fast even it's fully charged. What do you think the problem is?

[@BXT_LAB]

It's a bit strange that it would cause that problem after a fall. Could be a circuit board issue.

[@SpecSquadx]

Does Jisulife life 7 support fast charging? If it doesn't, can i still charge it with a 18 watt charger or is it bad for the battery?

[@BXT_LAB]

Life7 only charge normal 10W, but you can use any charger even much higher power. Charging power automatically depends on load. But use a good quality charger, not a fake one.

[@zurie_weiss]

Does adding grease/lubricant help with noise reduction? If the battery wears out, do you think it would be easy to replace the battery DIY?

[@BXT_LAB]

Noise is caused by the balance of the fan blades and the quality of the motor shaft. Adding grease can increase longevity of the motor shaft and prevent wear. Battery upgrade is quite easy, you just need to replace the battery cell, you need a battery welder or soldering iron and some knowledge about batteries.

[@jabroknee]

Jisulife Life7 vs Life9? Same $, which one??

[@BXT_LAB]

Life 7: Multi-form + % battery indicator + more battery life. Life 9: Strong wind in very compact size + more noise at high levels. Depends on your choice.

[@jabroknee]

@@BXT_LAB Thank you, going 7

[@MUXLegend-yg9xt]

It is now $14.75 in my place right now. Is it a good time to buy?

[@BXT_LAB]

For 5000mAh version, it's good.

[@KristineJoy-z1u]

Hi, good evening. Should i drain the fan first before charging for the first time? Or is it not recommended to drain the fan?

[@BXT_LAB]

You don't have to do that. Use it naturally. Just be careful not to drain it down to 0% too many times. If you don't use it for a long time, charge it to about 50-60%, don't charge it to 100% and leave it there for a long time.

[@KristineJoy-z1u]

@BXT_LAB hello! My charger has "5V 2A or 5-11V 3A MAX" on it. Is it fine to use this to charge the mini fan?

[@BXT_LAB]

@@KristineJoy-z1u no problem, it automatically compatible with your charger. Not recommended with 5V 1A because it charges very slowly.

[@KristineJoy-z1u]

@@BXT_LAB alright, thank you sm!!!

[@jacharissesantos7530]

Can i just pull the fan without removing the battery/speed display on the front ?

[@BXT_LAB]

Without the battery removing. But you must remove back cover and the front display. Under the front display is motor shaft locking ring, must be removed to take the propeller out.

[@michaelryaneuropa556]

Hello, I just want to ask your opinion on what could be the cause of the malfunction on my fine. My battery was at 90% then I used it like 10mins when I turned it back again it went 0% and it won’t start again. You can charge it normally, but when you try to use it again it goes back to 0% again. What do you think is the cause of that ?

[@BXT_LAB]

You can try opening it up and disconnecting all the connections, then putting it back in. If it doesn't work, then your battery cell may be bad and need to be replaced.

[@Naflate]

after i opened the fan and put it back the propeller suddenly stopped Spinning but it shows on the screen

[@BXT_LAB]

Check all wires and connections again.

[@eilve14]

planing to buy but i wanna know if you try using level 1 or 2? then how many hours it last?

[@BXT_LAB]

I haven't had a test at that level yet, I think it's easy to pass 5 hours at level 2.

[@razzel6667]

I'm worried it will eventually loose tread in the long run?

[@BXT_LAB]

Do you mean you are worried about it shaking when placed on a table?

[@razzel6667]

@@BXT_LAB no. I mean when you bend it

[@BXT_LAB]

@@razzel6667 i think it's okay, we don't fold it that much, unless you use it as a fidget toy😅😅

[@AceRussellRecto]

Can i ask how do i take the hair on the propeller without removing the front display?

[@BXT_LAB]

The back cover has a screw, you unscrew that screw and turn the cover counterclockwise to remove the cover. Then you have access to the fan blade, hopefully you can get the hair stuck in it. Try that. From 2:15.

[@AceRussellRecto]

@@BXT_LAB But the hair was like inside the properller

[@BXT_LAB]

@@AceRussellRecto So you still have to open the motor completely. You need a small screwdriver and a sharp tweezer. It's not hard, just tools and be careful with the wires and circuits. Follow as Video from 7:15.

[@AceRussellRecto]

How abt this, is the screw in propeller completely covered?

[@BXT_LAB]

@@AceRussellRectofollow the video bro😅

[@brentmurillo9329]

Hii just wondering where i can buy the clear white thing that locks the propeller and what is the name of that thing?

[@BXT_LAB]

You can find it in old cooling fans. Or buy some dirt cheap cooling fans just for take that part.

[@brentmurillo9329]

@@BXT_LABtyyyyy

[@kaze9660]

how did you remove the lock on the shaft?

[@BXT_LAB]

Use a tweezer, with a pointed tip, and poke into the slot of the axle lock ring. Wiggle it and it will pop out, be careful not to let it fly away😅😅

[@jihyomizuki9801]

What screwdriver is used to open the fan to clean it?

[@BXT_LAB]

It's just needs a small enough, plus shape tip driver. Open the back guard and clean it.

[@shamety2697]

Would using it while charging damage the battery?

[@BXT_LAB]

It's not getting hot or damage in short time. But need long term using in that way to verify.

[@BXT_LAB]

I think it doesn't.

[@shamety2697]

@@BXT_LAB okay, thanks for replying !

[@Pluto30678]

很喜歡看你拆解風扇，請問塗抹在電路板上透明的油酯是有何作用呢?

[@BXT_LAB]

@@Pluto30678 謝謝。該油脂旨在防止電路受潮，或如果 100% 密封，則可以防水。如果下雨或掉進水里，它可以保存我風扇上的電路板。

[@BXT_LAB]

@@Pluto30678 乾燥後，它會像橡膠一樣堅硬。

[@Pluto30678]

@@BXT_LAB 感謝解說，那麼這款風扇的品質您建議購買嗎?

[@BXT_LAB]

@user-pv3tl9fe8o 我覺得它的品質還可以。但風大時噪音較大。你可以考慮一下。

[@freshbakedclips4659]

The batteries are in parallel configuration? If that's the case, then I'm upgrading/replacing it with two 3500 mAh, total of 7000 mAh. I just bought 5000 mAh variant.

[@BXT_LAB]

Yes, they are in parallel configuration. You can absolutely upgrade it to 6800mAh or 7000mAh. For example 2 cells NCR18650B or Samsung 35E is perfect.

[@hanhlacyeudau]

Bản 5k với bản 3k6 có chênh nhau nhiều không bác

[@BXT_LAB]

Tuỳ chỗ bán bác ạ. Đây em mua tại Japan. Chắc tại VN chênh nhau khoảng hơn 100K. Nếu mà không cần dùng lâu thì mua bản 3600 cho tiết kiệm ạ.

[@hanhlacyeudau]

​@@BXT_LAB e hỏi về độ trâu ấy bác thấy có nhiều bác bảo cell pin bản 3k6 không kém bản 5k mấy

[@BXT_LAB]

@BIGBOSS-xi3zc bản 5000 của em chạy max được tầm 3 tiếng. Còn 3600 em không có nên không biết. Nhưng con này em thấy pin phải trên 15% thì vừa cắm sạc mới vừa dùng tốc độ nào cũng được. Pin cạn dưới 15% vừa sạc vừa dùng nó chỉ cho chạy cấp 1.

[@BXT_LAB]

@@hanhlacyeudaucon Pro 1S thì vừa chạy vừa sạc bất kể thế nào cũng ok, max speed được hết. Con Ultra 1 thì vừa sạc vừa dùng nó chỉ cho chạy 1%.

[@hanhlacyeudau]

@@BXT_LAB e này pin giấy thế à bác

[@mariedyltimola6385]

I use stainless ladle to rem the front black circle and ita effectibe

[@BXT_LAB]

You can use anything thin and hard enough. Be careful not to poke too deep and damage the circuit.

[@kaze9660]

is it normal when I shake the fan there is some clicking sound happening near to motor I think

[@BXT_LAB]

It’s normal. The shaft of motor and sleeve bearings have a tiny gap, cause sound when shaking back and forward. You can imagine.

[@kaze9660]

@@BXT_LAB ok bro thanks ( I subbed)

[@BXT_LAB]

@@kaze9660 thank you bro!

[@kaze9660]

@@BXT_LAB just wanna ask again bro what do you recommend a fan beside jisulife life 7 that is strong and at the same time is silent?

[@BXT_LAB]

@@kaze9660Do you want just handheld fan, or mini desktop fans are ok?

[@brentmurillo9329]

Where did you buy your tools?

[@BXT_LAB]

I bought them on Amazon. You can search “Phone repair tool kit”.

[@brentmurillo9329]

@@BXT_LABThankss

[@dudz2771]

Is it the same with pro1?

[@BXT_LAB]

No, it's cheaper and the wind is a bit weaker, charge slower. But can "transform".

[@Lutherman_edc]

Out of all the jisu fans which one would you daily use?

[@BXT_LAB]

JisuLife Pro 1S all day. It balances design, strong wind, operating time, and charging speed. Depending on your needs, here is my opinion. Thank you.

[@aa-ph4qj]

​which jisulife is the least noisy?

[@BXT_LAB]

@@aa-ph4qj I have not used all JisuLife models yet. If you need quiet, you can choose JisuLife FA18S, FA24, or similar but they are not handheld fans. If you want a handheld fan to be very powerful, the trade-off is that it is noisy.

[@jerickohjiroyun1537]

they should have, made the removal of propeller easier, for easy cleaning as well, because you removed so much part before removing propeller

[@BXT_LAB]

The back cover of the fan can be opened easily with a small screwdriver. Then you use a wet tissue and tweezers are recommended. As for the design of the motor and fan shaft, it is an industrial standard, not for regular users to disassemble frequently.

[@marvinsantos7699]

What is rpm on this jisu life 7?

[@BXT_LAB]

JisuLife Life7 speed: Lv1: ~2200rpm. Lv2: ~3200rpm. Lv3: ~3700rpm. Lv4: ~4200rpm. Lv5: ~4700rpm.

[@Zain.B.]

where did you bought a 5000mah battery??

[@BXT_LAB]

That's an option. You can choose between 3600mAh and 5000mAh version.

[@MonitoringCapiz2]

Teardown all Jisulife fan 😁 including the neck fan 🙂

[@BXT_LAB]

If I have 100,000 subscribers, I will definitely teardown all of them for you guys, LOL.

[@senpaiferdy8568]

Next one jisulife fan 4 plssss thank you

[@BXT_LAB]

It's the same fan, just the handle is different. But I'm sure it will be more difficult to open than this model.

[@amyshaw6657]

Amd or Intel?

[@BXT_LAB]

Why are you asking about computer CPUs here? My video is about handheld fans😅

[@itstriplerblx5887]

Between the Life 7 and the Goojodoq, which would you recommend? Which is stronger and lasts longer? I'm planning to purchase a Life 4 (basically a Life 7 without the bending neck and much cheaper). The goojodoq is a bit too noisy for me that's why im looking towards more conventional fans than the "turbo" ones.

[@BXT_LAB]

They are different. Goojodog is blow further but its design is not multi functional as the Life7. Also Life7 when straightening is slimmer, easy to put in some pocket. Battery wise, Life7 with 5000mAh version last longer than Goojodoq.

[@snowgirl8190]

Jisulife 3in1 portable fan teardown plz😁

[@BXT_LAB]

I'm also curious about that fan. I don't know if it uses a brushed or brushless motor.

[@MatteoTalastas]

Can you do life 8 plus

[@BXT_LAB]

Oh! I don't have that one.

[@MatteoTalastas]

Ok

[@BXT_LAB]

@@MatteoTalastas I’m also curious about that fan but i don’t like it’s design (in my opinion), no fan guard.

[@BXT_LAB]

@@MatteoTalastas I just made a post about it on the Community page. You can check it out, thank you.

[@MatteoTalastas]

I see it

[@Jo-ne7jc]

this or pro 1s?

[@BXT_LAB]

The Pro 1S is a bit more expensive, has a metal body, charges faster, and is more powerful. But the Life7 folds. It depends on which you prefer.

[@Jo-ne7jc]

@@BXT_LAB Thanks! Got a huge discount so i go for the Pro 1S for keeps!

[@BXT_LAB]

@@Jo-ne7jc That's awesome 😉

[@Jo-ne7jc]

@@BXT_LAB Cheers for this channel. Keep it up man! Big help to decide!

[@BXT_LAB]

@@Jo-ne7jc thank you so much!

[@ChauQuoc-pb4hj]

A test quạt goojodog thế hệ thứ 2 đi ạ e tính mua ko bt có ngon bằng cây này ko 🥲

[@BXT_LAB]

Chỗ anh hiện không có con đó. Nó nhìn giống Life7 thôi chứ chất lượng sao bằng bên JisuLife được em. Tiền không vấn đề thì mua JisuLife còn tiết kiệm thì mua Goojodoq.

[@ChauQuoc-pb4hj]

@ a ưi bật thêm phụ đề ik ạ có video test pin nhiều quạt ko có phụ đề tiếng việt ko hiu j cả:))

[@BXT_LAB]

@@ChauQuoc-pb4hjđoạn cuối video có mấy cái ô màu ý. Lần lượt các con pin trâu nhất tính từ trên xuống.

[@ameneiyd.b9046]

do jisulife life 9 bro

[@BXT_LAB]

I'm waiting for it to go on sale😅😂

[@Yooojayy23]

Finallyy

[@BXT_LAB]

😘😘

[@urbanorebosa]

bro it gives you an extra 200 mah.

[@BXT_LAB]

Yeah, the new Pro 1S recently also have more 200mAh than claim, and they have very impressive run time.

[@Juan5thTea]

great job! you just destroyed the looks of the fan!

[@BXT_LAB]

Thank you! For the curious to know what's inside.

[@mohdazi5133]

mine short circuit after few days. 😭

[@BXT_LAB]

😭Does it completely dead?

[@MatteoTalastas]

I have that

[@B_gL_ps5015]

Is it good? How long it lasts when you use lowest power?

[@MatteoTalastas]

Long life

[@caesaria]

don't add music please

[@BXT_LAB]

Sorry for that if you don't like it. Thanks for your comment.

[@julesamirjabuen7368]

I got mine for 16 bucks

[@BXT_LAB]

Very nice!

[@ผู้คลั่งไคล้ผัก]

too expensive fan

[@BXT_LAB]

I know it's expensive. Because it's JisuLife😅 But when you bought good products, i think it worth it.

[@iamnotcarlaa842]

@@BXT_LABya thats true, too expensive but worth it. Good investment

[@finnshanefilan5342]

Dạ con Nên mua Goojodoq hay jisu vậy Admin ơi​@@BXT_LAB

[@shukrimetal0043]

A good fan is expensive but worth it..

[@BXT_LAB]

@shukrimetal0043yes, everything which is cheap or expensive have some reasons.