JK Jikong BMS Installation tutorial by Big Wei Battery

A basic JK Jikong BMS Installation tutorial by Big Wei Battery
Feel free to comment and ask any questions to our technician
Welcome to our Brisbane store or shop online at:
www.bigweibattery.com.au

[@cyprienlefebvre7901]

Thanks for your help! i forgot to plug the 8th cable with the fourth, now it works perfectly thanks to you.

[@Roll2Videos]

I really Injoy the JK BMS's Thanks!

[@bigweibattery-brisbanecity9602]

That's good to hear.

[@odoohub5010]

What happens if the balance cable are connected incorrectly?

[@lee1983us]

When the bms is turned off and I probe the battery positive and bms “P - (minus)“ shouldn’t it read 0 volts? I’m reading 12v which doesn’t make sense because it’s turned off 🤔

[@bryansbusadventure4783]

I will be running a 24 volt system, I want to run 16 3.2volt cells configured to 24 volts, I have two of these batteries.. a total of 32 cells. the cells are rated at 280 ah. My MPPT is a 250/80 viltron unit. and I am running 4-540 watt solar panels on the roof of my motorhome. My inverter charger is a viltron 3000/24/70. I am trying to figure out which JK BMS I should run on each of these batteries.

[@pascalbudin2983]

Bonjour de France... Je suis en train d'installer une batterie comme la votre, serait il possible d'avoir le plan de connection de votre disjoncteur. Merci beaucoup. Pascal

[@praxis9744]

Hi, I have 16 cells running in parallel pairs of two (like you have 8 cells here running as 4 cells to 12v). The total voltage is 24v for my system. Should I connect each BMS wire to each cell or each parallel paired cell like you have in this video? What happens if you get a rogue cell that affects the pair? Thanks

[@bigweibattery-brisbanecity9602]

Hello! For the layout of the BMS and most BMS's, the balance wire is only able to balance with "one" cell. So you'd have to connect two cells in paralell for the required setup you need. So yes for wiring up the balancing cable you'd connect it to the paired cells like in our video. Plently of our LiFePO4 batteries has this paired layout and it is able to work with eachother well in paralell together. I hope this helps

[@mgreenesco9955]

I have 2 Jk bms in my system and think they're great. The only feature I wish they had was current limiting when the cells are near full charge so you can charge slowly while balancing instead of it having one cell hit your set voltage and fully stopping charging even though other cells will accept more.

[@ocular57]

Sounds as though you pack is significantly out of balance, so to reduce the likelihood of a fully charged runaway cell tripping BMS over cell voltage (3.65v) reduce your charger pack voltage ~14V and check that balancing is activated. Now leave battery balancing and watch delta V reduce from 100-200mV and once delta V is

[@hypersleep9704]

Thank you for time and video. Its better to left a small space between cells? All others people splitting cells without free space.

[@bigweibattery-brisbanecity9602]

Hello! Our design has the high density foam between the cells which gives vibration resistance. Escpecially for use in vehicles.

[@argi0505]

Mine doesn't turn on at all? Any Idea?

[@Roland_Deschains]

How to update software on jkbms?

[@Mike-01234]

I just bought a B2A24S2OP looking at the wire size 2 8 Gauge wire how can it handle 200 amps continually. 8 AWG wire can handle 55 amps each so two in parallel would be about 120 amps not 200. This thing says it can go to 350 max can't see how this wire can do that. The video your is much heavier connections.

[@evil17]

He was using 6awg cables, would be more suitable

[@MrDenisJoshua]

Where can I buy that battery please ? Thanks

[@bigweibattery-brisbanecity9602]

You can check out our website www.bigweibattery.com.au/

[@aykutuzun34]

3.2v 100Ah X 8 Cells = 12.8v 200Ah? Bms JK B1A8S10P ?