Joy it tester T7 - Longer Battery Life Mod!

  Рет қаралды 2,702

tinkering.online

tinkering.online

Күн бұрын

Пікірлер: 10
@pault6533
@pault6533 Жыл бұрын
I did the same thing on mine with 2400 mAh cell. My cell was bigger so I had to remove the white 2P connector from the board and solder the wires directly. Later, I found out some components would "stump" the tester, causing the processor to freeze with the display on. I opened the case, removed and reconnected the battery. It worked fine, then was stumped again with the same component. So I added a sliding power switch recessed into the side of the case with the charging circuit. If the unit locks up, I can use my fingernail to disconnect and reconnect the battery, no disassembly needed. This has happened a few more times so I am glad I added a switch. The unit needs to go through calibration after turning the switch back on.
@AlexSamuelsgolden
@AlexSamuelsgolden 4 ай бұрын
NEW bATTERY PART Number Please !
@uni-byte
@uni-byte Жыл бұрын
I'm in agreement with two of the other's here. That type of connector comes apart fairly easily. It may superficially look like it is locked, but it's not. Those "two white locking pins" do not move. The PCB mounted casing spreads apart a little when you insert or remove the plug.
@Janvanderkloes
@Janvanderkloes 4 ай бұрын
5:43 Lekker Joh .......Goed bezig Knippen maar !!!!!!
@Janvanderkloes
@Janvanderkloes 4 ай бұрын
Sukkel
@robertwebb5586
@robertwebb5586 7 ай бұрын
Add a on/off switch to it. It has a standby circuit in it for the start button. it'll discharge the battery just by sitting there.
@hermannr.1277
@hermannr.1277 Жыл бұрын
780 people have seen you being defeated by a simple PCB connector, that would normally just need to be pulled out (it will resist a bit, because that's what it is supposed to do)... then you cut through both battery cables at the same time, making a really nice short circuit (hopefully the battery protector did its job) and _twice_ ... 😖Really???
@danedewaard8215
@danedewaard8215 Жыл бұрын
Just pull that connector out! I know you can do it!! Now you know how Dr Frankenstein felt!!!
@saydmarschany8321
@saydmarschany8321 9 ай бұрын
Good job, you should have used heat shrink instead of black tape. Otherwise, well done.
@topeye4202
@topeye4202 11 ай бұрын
Add a power switch will help more than a bigger battery i guess.
Китайские тестеры компонентов - какой выбрать?
11:14
Заметки Ардуинщика
Рет қаралды 323 М.
ССЫЛКА НА ИГРУ В КОММЕНТАХ #shorts
0:36
Паша Осадчий
Рет қаралды 8 МЛН
Jaidarman TOP / Жоғары лига-2023 / Жекпе-жек 1-ТУР / 1-топ
1:30:54
RC plane retractable landing gear
1:08
thang010146
Рет қаралды 3 М.
Доработка Транзистор-тестера LCR-T7
20:48
мультифункциональный тестер Т7
7:37
JOY-IT LCR-T7 Multi-component tester - review
46:01
MrVideoTronix
Рет қаралды 17 М.
LCR T7 - Multi-Function Tester
12:03
Power Battery Channel
Рет қаралды 71 М.
Power Switch For T7 Tester : Sponsored by SolderStick Wire Connectors
21:17
Simple Upgrade for TC1 Multi Function Tester
10:08
bertoid
Рет қаралды 36 М.
ССЫЛКА НА ИГРУ В КОММЕНТАХ #shorts
0:36
Паша Осадчий
Рет қаралды 8 МЛН