Jura Machine Doesn't Make Coffee - Water/Coffee Runs Directly Into the Drip Tray

The beautiful Jura impressa J5 does not only impress with its elegant and timeless design, but it also convinces with its sophisticated and robust technology. In this model from 2008, however, a small defect in the outlet valve prevented the freshly brewed coffee from flowing into the cup. I hope this video can help you out solving similar problems in the future. Have fun watching!
M Y T I P - B O X
_________________
www.buymeacoffee.com/myworks ☕
www.paypal.me/ytmyworks
Affiliate links:
Bezahlter Link:
U S E D P A R T S
_________________
OKS Multi Silikonfett/OKS silicone grease: amzn.to/3cX39eV
O-Rings: amzn.to/37XGH3j
Oval Bit: amzn.to/3c1PHIt
Aluminum sleeve: amzn.to/3jpc7F6
M Y W O R K
______________
00:43 disassembling
01:44 removing the brewing unit
02:29 disassembling the brewing unit
05:19 repairing the drainage valve
05:38 cleaning the chassis
05:59 removing the water connector
06:39 assembling the drainage valve
08:22 installing the brew group
08:55 function test
#JuraImpressa #Repair #Restoration

[@johnsall6274]

This is my second Keurig Coffee Brewer. kzbin.infoUgkxBrV-RbF5Nk0Rlt9i15aao-YMzqzTG8Vf The first one lasted 6 years. It worked beautifully until the day it didn't. It was hard to go back to the drip coffee for a couple of days while I waited on my Keurig to get here. There is a huge difference in the taste. Keurig makes a really good cup of coffee. This new one is a little different from my old one. I find putting the water filter in was easier than on the old one. Attaching the water reservoir was also a little different but once I figured it out, it too was easier. This new one has the auto off feature but is not programmable like the old one. Only three cup sizes instead of four. The odd thing for me was how much lighter in weight this one is compared to my old one. More plastic and much less metal in the construction of this one. The price is so much less than the original Keurig that I bought and the coffee tastes the same so all in all I am satisfied.

[@klejb]

Thank you! Without this video, troubleshooting my machine would have taken much longer. Parts are now ordered.

[@gregschroeder5828]

Amazing! I wish there were more KZbin videos this detailed, efficient and well done.

[@the7cantlose]

Thank you very much! My F9 was having this problem. You're the best!

[@krzysztofsnarski9219]

Thanks for tips, repaired my Jura, same issue, good job!

[@miningexcavator]

Many thanks for uploading this video. I am fixing my Jura machine following the same steps. I am having the same exact issue.

[@amillsmcewan1]

Very useful video thank you.

[@stefanocimino8759]

complimenti fai sembrare tutto facile ottimo lavoro

[@henkzaanstad2256]

Geweldig. Dank je wel voor deze film.. Groet, Henk uit Holland....

[@TheCrazyFix]

thank you very much my jura f70 is working 100% again

[@marc7484]

5:06 probably the best scene ever!

[@mironi723]

Dobra robota. Pozdrawiam

[@nelsongonzalez6292]

thaks very much you save mi nelson colombia

[@StoneFreeITS]

Thanks for an excellent video! I recently bought a defective J5 and got it to work by replacing the valve with a new one bought with the aluminium piece mounted. I also replaced the sealings for the valve and water tank. After assembling and every day it takes about three cups before coffe comes out of the nozzles. For the first cup comes nothing, the second cup maybe 2 table spoons and some air. A little more for the third cup but still some air. The fourth cup comes as it should. Grinded coffee in the waste bin for the first cups is dry.

[@yt.myworks]

Hello, did you put the seals inside the valve in the right place? The open side of the seals must be directed inwards. You can make a coffee without the coffee grounds container, like I did in my video. After that, you can see where the water is going.

[@haiping0918]

hope i never need to do that. thanks for the info.

[@brianiswrong]

That was a really dry puck at the end. The machine certainly got the most out of its coffee grind 👍

[@tegabazunu4030]

Mine is Jura impressa S901

[@Nick-bu2hr]

I have the same with my Jura Ena 8 what would i need to do vielen dank!

[@tegabazunu4030]

Hi, can I bring mine to you? Because it ha has the same problem and I can’t do what you did here,please

[@jevonbarnes4390]

can i send my jura A9 to you and p ay to have you fix it? I am having the same problem.

[@NajmDevelopers]

Hi there My machine is doing the same can you help me at all?

[@minoumueller5281]

Are you located in the USA and is it possible to have you repair my machine?

[@Digging-life]

I have this problem but on a delonghi can you advise ? Thank you

[@yt.myworks]

This can have many causes. Calcification of the hoses, defective water pump, leakage in the brew piston, etc.

[@ronanderson6653]

I am having the exact same problem on an Impressa X90 and the valve looks good.. I have removed it and all looks in tact. Any suggestions other than this?

[@yt.myworks]

I think you should change the lip seals inside the valve. See my other video on the brew group overhaul: kzbin.info/www/bejne/sGPGn3xonZmljKc

[@Helgemainn]

Hi. Where do you get the aluminum sleeve? Made it yourself? I need one. Best regards, Helge, Norway.

[@yt.myworks]

Hello, the aluminum valve cap is bought. You can search "Jura Drainageventil" on ebay or amazon.

[@Andreas5423]

@@yt.myworks Thanks for the great video. Where can I get another plastic sleeve or aluminum valve cap? (the search phrase you mentioned here ["Jura Drainageventil"] doesn't bring up anything up on Amazon...typo?)

[@arifwe7999]

I had problem like this on my delonghi etam 36.365.is the problem from brewing unit or brew piston?thx in advance

[@yt.myworks]

There is another problem with a Delonghi, see my other video on the subject: kzbin.info/www/bejne/aYKlfaKKgsyHm8U

[@arifwe7999]

Already dissasemble the mechanics valve as instructed in your video,buat still,there was no water through it when the valve press

[@salihonder7607]

Hello. Tool at 06.05 seconds of the video. Where can I purchase the Tool you used to remove the water connector?

[@yt.myworks]

www.juraprofi.de/Werkstatt/Werkzeug-und-Silikonfett/Werkzeug-zum-wechseln-der-Wassertankdichtung::10728.html?refID=gbase&gad_source=1&gclid=Cj0KCQjw5cOwBhCiARIsAJ5njuYZTGMFkeBQmOO3qi5GNR2t36-PECT8kzjl5Fxo-h0nK8TgR99M4GYaAlpxEALw_wcB

[@jakubkozowski7500]

Where can I buy the tool visible in the 6th minute of the video?

[@yt.myworks]

You can find the tool on eBay or here: www.juraprofi.de/Werkstatt/Werkzeug-und-Silikonfett/Werkzeug-zum-wechsel-der-Wassertankdichtung::10728.html

[@Andreas5423]

What error message were you getting, was it "Fill Beans" even when beans were in the hopper?

[@yt.myworks]

You need to check how much coffee is ground. If the amount of coffee is too low, the machine displays an error message. In this case, the grindstones may be worn and need to be replaced.

[@zztv11]

Hi My Works, Great video, thank you! I have Jura J9.3, I disassembled brew unit, cleaned it, checked drainage valve small plastic piece isn't broken. Assembled brew unit back and still coffee is not coming out. I think coffee drips directly to the drip tray. Should I replace small plastic sleeve with aluminum sleeve on drainage valve? Any other ideas? Thank in advance.

[@yt.myworks]

Either you buy a new drainage valve or you change the sleeve and the seals inside.

[@anrir5517]

@@yt.myworks Thank you so much. Another quick question. When I run "Rinse the Coffee System" water is not coming out front, I think it goes to drip tray. Do you know if "Rinse the Coffee System feature will work normal with replacement of new drainage valve. Or could it be another part not working correctly?

[@zztv11]

@@yt.myworks i replaced new drainage valve still coffee is not coming out. Any ideas?

[@yt.myworks]

@Anri R I think so, that is the main cause of this error. But you should also clean the brewing group and install new seals.

[@yt.myworks]

@O S does the water get into the drip tray? If there is no water at all then the water pump may be broken. You need to check the pump.

[@bryanpayne5509]

Exact issue I’m having but spring and components seem to be working great, piston engages but then disengages and allows all water to bi-pass coffee grounds and all water goes into the bottom still… any suggestions?

[@yt.myworks]

You'll need to replace the mold seals inside the valve. These wear out over time.

[@bryanpayne5509]

Thanks so much I’ll check that out!

[@mguerramd]

My old F7 brews coffee fine and it comes out the spout. But in cleaning mode all the fluid comes out the drainage valve in to the tray and none of it comes out the spouts. Might that somehow be related to this issue?

[@yt.myworks]

I can't say for sure, but the seals in the drain valve could be defective. Is the coffee grounds container dry after making coffee? If not, this indicates a defective drainage valve.

[@mguerramd]

@@yt.myworks ok thanks

[@volodymyrbalandiukh7145]

Where to buy a cappuccino maker for the Jura J7 coffee machine, thank you

[@yt.myworks]

@Volodymyr Balandiukh: You have to search the internet for "Jura Profi Auto Cappuccinatore". There were Jura models with different fine foam nozzles. Please check in advance whether your coffee machine has this adjustable professional fine foam nozzle or the simple fine foam nozzle. LG

[@volodymyrbalandiukh7145]

@@yt.myworks Thank you!

[@Digging-life]

I have this problem with a delonghi dinamica can u please help ?

[@yt.myworks]

What fault does your DeLonghi have?

[@Digging-life]

@@yt.myworks doesn’t rinse it goes in to tray and doesn’t make coffee

[@Digging-life]

Had it bits yesterday all hoses are ok, water pump fine. No water in brew piston

[@yt.myworks]

You have to disassemble the case and see where the water is coming from.

[@leifseger]

This is a great video, but I cannot remove the plastic pieces just before 2:49 in the video. The are stuck at the point close to the unit you are removing at minute 2:49. For you it seems so easy to remove, but I seem to have an extra "hook" on each side. Any suggestion?

[@yt.myworks]

Two of the clips are somewhat hidden. Try moving the brew group to a different position, the clips will be easier to reach. You can feel them with a flat screwdriver.

[@ryanaqzina3efen594]

What's the name of the tool on 6:20? Thx!

[@yt.myworks]

www.juraprofi.de/Werkstatt/Werkzeug-und-Silikonfett/Werkzeug-zum-wechseln-der-Wassertankdichtung::10728.html

[@rususerghei9343]

Seriously... no one recognized the LEGION MOVIE....

[@acewing24]

Damn.... where can I get a aluminum piece ? Lol my last service was 400$ to fix this... now I believe it happened again. Now I'll take it apart myself to see if it actually is the plastic piece broken. 🤔

[@yt.myworks]

Search in your country for "Aluminum Cap Sleeve for Drain Valve Brewing Unit Suitable for all Jura Impressa". There are also versions in plastic or brass, all of which are well. But be careful with the valve, the bend quickly put on the cap. Before you order the spare parts, first check what has broken.

[@acewing24]

@@yt.myworks thanks. I took it apart last night and was able to access the spring and sleeve. Was not broken, I believe fine dust is causing it to not slide as smooth as it should. I wiggled it and manually closed and opened the valve by pushing the spring in and out a few times. Coffee is pouring g again.... lol go figure... you think food grade lubricant would help ?

[@yt.myworks]

@joe shmoe I recommend cleaning everything thoroughly, changing the lip seals and O-rings and lubricating something. Buy a seal kit like this one: amzn.to/3k4sqcp. See my other video on the same topic: kzbin.info/www/bejne/sGPGn3xonZmljKc

[@Getsitdone]

With spending $200…?