Just blown away by this process. I had no idea. I have tons of work to do, but actually watched all of part 1 and 2, and it wasn't time wasted. So impressed.
@youwelirka17377 жыл бұрын
Любо дорого посмотреть.Вы просто Красавчик!Глядя на вашу работу хочется пробовать повторить.Вдохновенно!
@SAVAGE308SNIPER8 жыл бұрын
No wonder this shit is expensive. Great work!
@KiengMeymey6 жыл бұрын
SAVAGE308SNIPER 2019
@dwdidit36643 жыл бұрын
I think you display the most patience by not going haywire on all the dumb questions you must receive!
@JewellerMakes10 жыл бұрын
Thanks again for showing your amazing work Jura. I'm fascinated to know how you work out the exact spacing of the dividers when marking out? After going around the whole diameter your last mark meets the first perfectly, how do you do it? Incredible..
@diasetter10 жыл бұрын
Hi G. I got just lucky this time. but if I'm not i have a trick.
@JewellerMakes10 жыл бұрын
diasetter I see. I don't seem to ever get lucky! I always end up with half a stone size left over after working around the circumference then have to keep using trial and error until they meet.
@calvinle658310 жыл бұрын
G Hughes You could divide exact the number of stones by using this formula: Diameter x 3.14 = length / size of stone you want to set...Ex: the circle = 25mm * 3.14 = 78.49mm / 1.3 (size of stone) = 60 stones. Always you need to find the lengh then divide the size of stone... hope it help
@JewellerMakes10 жыл бұрын
Calvin Le Thanks Calvin, I'll give that a try. In your calculation do you allow for any space between the finished set stones or the fact the the stones become slightly closer as they are set below the surface of a curve?
@diasetter10 жыл бұрын
normally it works only on the paper and computer.
@ZayPatino6 жыл бұрын
Damn imagine how long it takes to bust down a watch.. deff an art good stuff man
@bombgames15794 жыл бұрын
@Abd Elnour What are these tiny diamonds called? I keep searching to buy some tiny ones, but i don't find them :'(.
@mishagermanovich4 жыл бұрын
@@bombgames1579 Regular round Melee-size diamonds. Anything under around .2 carat is considered a Melee Stone
@TrapHouseTV6 жыл бұрын
I would be scared to do something wrong and destroy the watch... :(
@Dimagiorp6 жыл бұрын
That’s why they don’t let just anyone do it... you have to know your shit
@Stopwatchingthenews5 жыл бұрын
I’ve been setting for 25years and have that feeling with every expensive job I start
@Blackmage504 жыл бұрын
@@Stopwatchingthenews I've been setting for about 3 years and get that feeling every job. Lol still a young guy so it'll be awhile before I get any big jobs.
@jbzone1006 жыл бұрын
Great crafts man !! Takes time and persistence nothing but respect brotha
@PhatkatCollections5 жыл бұрын
Awesome video. If I wanted to start experimenting learning this art on my watches what would you recommend ?
@diasetter5 жыл бұрын
you can take a class or just try learning by watching
@joejo627311 ай бұрын
What a craftsman......incredible skill and attention to detail.......this kind of skill is so hard to find these days.....My respect to you and Thank You for your upload.
@gedasgold19866 жыл бұрын
Дааа. Хоть видео и четырех лет давности, но оно очень хорошее и поучительное. Я наблюдаю где-то три года за разными мастерами, но Юра лучший. Всё чисто, ясно, без вые...ов:) Сам мастер прогрессирует и другим пример даёт. Большое спасибо.
@talismanesoteric8 жыл бұрын
thanks JURA, because i need a special camera for my works.
@beetlejelly9 жыл бұрын
Hello, Jura, Thanks for the wonderful videos. What type of divider are you using for layout?
@asifabdul37632 жыл бұрын
Sir, please teach me..how to measurement diamond in watch...please sir one video..🥺
@edivinity57913 жыл бұрын
Always thought hand craftsmanship like this on stainless steel would be really difficult because it’s harder then gold and silver, but dam he sure makes it looks easy 👨🏻🍳💴
@sahidulmd66432 жыл бұрын
Awesome will teach me
@Lenmil10 жыл бұрын
Awesome as always. Thank you for sharing.
@RDA.BHARAT3 жыл бұрын
What was size of watch How many carats did you use And what size diamonds you used
@letham76873 жыл бұрын
what is this paste called to hold the piece?
@diasetter3 жыл бұрын
what you see is thermoloc. I don't use it anymore to do watches. no I use only collets: facebook.com/jurafinejewelry/photos/p.1367225990000980/1367225990000980/?type=3&av=282994661757457&eav=AfYFzQQZbmbBgaV6YVrq0rz6gr2IriG0hEdCm5Tcp5MSGeNR8D7B5dTaOPs87RiysIw
@talhahishma21669 жыл бұрын
Hi Jura, thank you for lovely video : I wonder what motor you are using ? is it a mart machine? if it is yes marto machine then I am interested in knowing from where I can get one. thank you for your help
@FlushingStatic Жыл бұрын
How many 1.7mm stones does the case take? Everything except the dial?? Milgauss if that makes a difference
@icemanbling75434 жыл бұрын
How can i take out diamonds from a ss watch i have. Around 10 diamond watches with decent size stonds i would say 3pts each stone 2mm size i have I would say in total 1200 stones i want to take them.out and use them for jewelry this stones are si1 quality
@johnadams-wp2yb10 жыл бұрын
I generally use a centre punch and super-glue!
@royrogers9839 жыл бұрын
Yeah he's definitely going at it all wrong..
@thaisonlekim3848 жыл бұрын
hfhvgutry
@jadanicole87509 ай бұрын
how well does that stay long term do any diamonds ever fall out after time goes by ? Does it take away from the overall look?
@nathanc.88216 жыл бұрын
What a shame that part 2 can’t be viewed any longer.
@diasetter6 жыл бұрын
its all because of stupid utube policy. i have always music in my workshop. utube robot thinks im using music to promote my stuff. thats why its blocked.
@RICHCREWSPLASHSET6 жыл бұрын
diasetter upload with no sound
@patrickbennett4396 жыл бұрын
that shit takes a fucking LONG ASS TIME dam i didnt realize before. wow
@KnightDriveTV6 жыл бұрын
Holy crap...I thought he'd drill some holes and glue those f*ckers in there...he whittled it down to all settings...holy hell.
@tikarbawahrumah8403 Жыл бұрын
i blow my screen after seen the flakes and chips... and realize how stupid i am..
@Angel___008883 жыл бұрын
Whats the name of the thing you are using to stick the ring instead of shellaxc
@diasetter3 жыл бұрын
thermoloc
@Angel___008883 жыл бұрын
Thank you so much
@seyithanakpinar24579 жыл бұрын
harikaaaa tebrik ederim elinize saglik 👏👏👏👏👏
@vikzvikz49437 жыл бұрын
Can you install diamonds on plastic?
@Saywhatohno4 жыл бұрын
what is the burr size you used? Do you have a training schools or courses for this kind of jewelry making?
@diasetter4 жыл бұрын
for classes: www.juratrainingcenter.com
@diasetter4 жыл бұрын
for tools: www.juratools.com
@BrockPlaysFortnite4 жыл бұрын
Sick
@rocketthelegend46094 жыл бұрын
Lol
@rocketthelegend46094 жыл бұрын
Its brock
@rocketthelegend46094 жыл бұрын
I follow u since 150k
@tonytonyyy18512 жыл бұрын
Can i put real diamonds on replica watch stainless Steel?
@Christiaaaaaan9 жыл бұрын
Hey Jura! Thank you so much for sharing your work! I have a big question. I have the 071 carbide burs. Very good burs, but sometimes when i drill they jam and there is a kind of star. Not a nice round hole. What can i do to prevent this? The problem mainly occurs in soft metals (silver) best regards!
@diasetter9 жыл бұрын
Hi Christian. sometimes it happens to me too. try slow speed. on my micromotor, i figured, 3000rpm is good for drill bits and ball burs and 5000rpm for tapered and cylinders.
@Christiaaaaaan9 жыл бұрын
diasetter Thank you very much :) I have the Saeshin Black Extreme. Outstanding perfomance, not expensive, and very good handpiece! Best regards from Austria!
@alexbreitling79558 жыл бұрын
Hello Jura. Please tell me what kind of headpiece are you using? If you don't mind. Thank you.
@diasetter8 жыл бұрын
hi Alex. all tools i use you can see on my website www.juratools.com
@alexbreitling79558 жыл бұрын
diasetter Thanks for you attention. I saw your tools but there is no description about hand peace. Is it NSK ,Foredom, marathon, Oz Plus ? Or just different brand witch is private?
@diasetter8 жыл бұрын
Handpiece is NSK
@alexbreitling79558 жыл бұрын
diasetter Thank You Jura. I appreciate it. 7.8 Ncm for micromotor it's animal power for drilling gold and metal.You micromotors are the best I think.
@diasetter8 жыл бұрын
also it feels like a pen in your hand. because shape and size.
@savestheday2583 жыл бұрын
Hello, Im curious about your tools, I've seen you use both a Lindsay Handpiece and also a GRS Handpiece. Do you prefer one over the other for stone setting? And also do you prefer one or the other for engraving work?
@diasetter3 жыл бұрын
i dont use Lindsay anymore. I made my own machine. its called JURA ARTgraver.
@diasetter3 жыл бұрын
kzbin.info/www/bejne/rZ7CnZ6woceApNk
@asda89922 жыл бұрын
@@diasetter ❤
@bimandas14373 жыл бұрын
There are no vacancies for work? please tell me
@Tdontworry3 жыл бұрын
Great video, 👍🏽 What's the name of the wheel on your micro motor you are using to re sharpen your drill bits ?
@diasetter3 жыл бұрын
diamond cutting wheel for making groove and and tip. blue diamond wheel for sharpening lips
@Tdontworry3 жыл бұрын
@@diasetter thank you 😊
@andrewtobin7538 Жыл бұрын
Stainless steel?...no way it cuts that easy!
@frankrusso42535 жыл бұрын
Does this stop the bezel from rotating ?
@diasetter5 жыл бұрын
i used to use it for holding. not anymore. working witt special collets now
@talhahishma21669 жыл бұрын
Marto is a trademark name for motor . did you use it in the video at 16:30 minute to make line, do you have this motor on Jura tools website? Thank you
@yolodolo91434 жыл бұрын
When people ask why jewlers charge so much for the merchandise. This is why.
@alee48668 ай бұрын
what drill bit can do stainless steel
@gliderjewels3 жыл бұрын
Beautiful, my thermolock always starts to melt and move when working on small pieces because of the heat when drilling.
@diasetter3 жыл бұрын
for small pieces i prefer shellac
@gliderjewels3 жыл бұрын
@@diasetter Thanks! I'd considered giving that a go but hadn't got round to it. Ill definitely pick some up. Keep up the great work, these videos are very enjoyable.
@gliderjewels3 жыл бұрын
@@diasetter Also, How did you calculate what diamond size to use and how to have them perfectly match up at the end? Is there a formula to use for this?
@diasetter3 жыл бұрын
the best way is PC. and my digital divider
@reviewonpoint50653 жыл бұрын
Thanks for sharing im learning from videos and i work on my own watches i hope i will make a professional job of it
@danielrp2000dr4 жыл бұрын
What is the name of the tool with 2 spikes that he uses for scratching the bezel and poking the holes for the stones?
@mattchedzey6 жыл бұрын
Hello, is there a reason why when you are reaming out each hole that you jump two and then go back one, jump two, go back one etc?
@sh40945 жыл бұрын
There has to be a machine that does this shit.
@edgar1984i2 жыл бұрын
Здравствуйте что за сургучь? Это обычный сургуч такого цвета ?
@diasetter2 жыл бұрын
это thermoloc
@valeriaperelsztein1700 Жыл бұрын
Bellisimo❤
@АлександрРостов-т8в9 жыл бұрын
Ну и ещё один вопрос, диски на которых вы затачиваете и доводите штихеля,если можно название и зернистость.
@samuelshamilov33034 жыл бұрын
Диски немецкие алмазные а резинки там три вида фирмы edenta там коричневая она для обдирки потом синия для заточки и желтая для финиша
@uniqueartjewelry10 жыл бұрын
Thank you for sharing, I have a lot to learn.
@ckennedy0019 жыл бұрын
What type of magnification were you using? Very clear and large. Thanks
@wootexclusive84993 жыл бұрын
My man got craftsmanship. U gotta pimp out my gshock homey
@ryanleamen5883 Жыл бұрын
How does the stone stay in place without falling out
@diasetter Жыл бұрын
Super Glue
@angelodinis30689 жыл бұрын
Nice to see your work!!! Can you answer me something? whats the average of stones that an experience stone setter can put by day? Thank you
@luisherrera86286 жыл бұрын
what is the name of the pasta with which he fixes things .and Where can I get it
@diasetter6 жыл бұрын
on this video its thermo loc. now i dont use it anymore. i have special clamps for holding watch bezels.
@AkbarAkbar-pe3jy11 ай бұрын
Wonderfull.
@capo17hg222 жыл бұрын
Impressive
@delantunh91663 жыл бұрын
King of the bongo king of the bongo 😂😂🔥🔥🔥🕺🕺🕺🕺
@LMSALIANCAS6251 Жыл бұрын
🎉
@asrafulsarkar31152 жыл бұрын
Nice
@Некрус9 жыл бұрын
Приветствую) По стали разделка? Штихель тяжеловато идет)
@asrafulsarkar31152 жыл бұрын
Hi
@toomanycactus31384 жыл бұрын
Isn’t there a tool also to stamp the drill spots. Kinda like a coumpass almost?
@diasetter4 жыл бұрын
i never make drill spots. waisting of time
@johnscroggins78972 жыл бұрын
What is that grey putty called
@diasetter2 жыл бұрын
its called thermoloc. i dont use it anymore for this kind of bezels. brass collets are much better.
@TaingSamreth2 жыл бұрын
The grey paste, what is that name?
@diasetter2 жыл бұрын
Thermoloc
@destry112266 жыл бұрын
Bro made a custom drill bit for it on spot that's crazy
@talhahishma21669 жыл бұрын
Hi Jura, Is the micro machine works like a hummer at 16:30 and like a drill ?
@MrPINKFL0YD6 жыл бұрын
I HATE iced watches but that guys skill is amazing!
@andyliang47334 жыл бұрын
what machine are you using at 6:36 ?
@kevinkev1530 Жыл бұрын
👍🏾👍🏾
@douro204 жыл бұрын
Do you have to be able to sharpen your own drills?
@diasetter4 жыл бұрын
watch this video: kzbin.info/www/bejne/epSQkntofJain6s
@heavensent61146 жыл бұрын
When you buy jewelry they tell you these are custom hand pieces
@nazmiyeozturk75123 жыл бұрын
21:01 😂
@pucksaopicksa55315 жыл бұрын
Thanks so much for sharing..
@asrafulsarkar31152 жыл бұрын
👍
@abdullahalzaid17036 жыл бұрын
are bezels made from scratch or bought originally ?
@diasetter9 жыл бұрын
never heard about this motor. micro motor that i use you can find on my web site
@freddyarroyo86007 жыл бұрын
hey umm can u email me plz mines starts tripin cause of my broken screen or do u guys have Instagram
@cloutline7 жыл бұрын
Freddy Arroyo dude seriously!? You aint got enough money for a new phone but you want diamonds set in your shit?!?!? Lololol dude im fucking dead. Pls tell me this was a joke. Ppl these days are something else i swear 😂😂😂😂
@kirozahariev5024 жыл бұрын
Nice ❤️🇧🇬
@cocaynne72262 жыл бұрын
Hello what type of graver you use for bright cut can i have some help people pls
@diasetter2 жыл бұрын
60 deg. carbide
@cocaynne72262 жыл бұрын
@@diasetter thank you so much. Is it knife flat oval ? What type ? Thank you so much i apreciate your work hope we see next videos
@diasetter2 жыл бұрын
for bright cutting i use mostly 60 degrees V-SHAPE (NEVER ONGLETTE) carbide gravers. i dont know any other names for it.
@cocaynne72262 жыл бұрын
@@diasetter the best answer finaly gooooooos thank you sooo so much i discover thag tool . I love you thankssss
@diasetter2 жыл бұрын
dont forget to put a little radius on the tip of your graver if you use carbide gravers. especially if you work on stainless steel
@lilflatty24726 жыл бұрын
Why not do this on a lathe and a mill? Much more accurate
@pasquale788 жыл бұрын
This video is so relaxing. I could watch this all day.
@ClaushCraft97410 жыл бұрын
super amazing, thank you very much.
@АлександрРостов-т8в9 жыл бұрын
Юра внутри чем вы выпалировываете перед закрепкой? если можно с названием и номерами)) спасибо.
@diasetter9 жыл бұрын
ya ne poliruyu pered zakrepkoi. tol'ko rozovoi rezinkoi ubirayu obloi s konchikov krapanov
@HH-qdzb10 жыл бұрын
工具 真棒 在哪里能够买到
@diasetter10 жыл бұрын
www.juratools.com
@HH-qdzb10 жыл бұрын
我在中国 怎么购买 无法邮寄
@HH-qdzb10 жыл бұрын
香港国际珠宝展 能够买到吗?
@diasetter10 жыл бұрын
赵斌 yes
@HH-qdzb10 жыл бұрын
谢谢
@1024.4 жыл бұрын
good job
@asfdj33338 жыл бұрын
Why do you cut inside on 21:30
@marica5354 жыл бұрын
Wow 👍👍👍
@ronaldkundla117910 жыл бұрын
Jura, is there any particular reason why you drill your holes between the marks you made with the dividers instead of on the marks?
@diasetter10 жыл бұрын
hi Ronald. do you know any reason to make a mark and then immediately remove it by just drilling on it? why do we mark at all? anybody has an answer?
@ronaldkundla117910 жыл бұрын
diasetter I always figured it was just to use the marks as the starting point for the drill, or at least that is how I use it. I'm always looking for ways to improve, so I was certainly curious about your technique. :-)
@diasetter10 жыл бұрын
Ronald Kundla this is one of my golden rules: never drill on the mark. don't remove your reference marks. since I'm not a machine i want to see them until the last second. unless you work with large gaps.
@Funplacestobe4 жыл бұрын
Trying to learn so I can start my own watch brand
@diasetter4 жыл бұрын
Good luck!!!
@MrJamel12583 жыл бұрын
What burr did you use for stainless steel?
@diasetter3 жыл бұрын
i use only carbide burrs
@talismanesoteric8 жыл бұрын
hello ! it's a great video, what camera you use for recording ? thanks
@diasetter8 жыл бұрын
at tis time i was using JVC. now Sony
@LeoFreese6 жыл бұрын
Can you post part 2 with no sound
@diasetter6 жыл бұрын
im sorry, too busy right now. ill repost second part as soon as i can.
@diasetter6 жыл бұрын
i just posted part 2. and its not blocked yet.
@michaelyoung68373 жыл бұрын
A work of art
@freddyarroyo86007 жыл бұрын
can I take my watch and wait for it or how does this work I have a watch and I want diomonds on it
@diasetter7 жыл бұрын
Hi Freddy. if you want to discuss it, here is my email: info@diaset.nl
@Watchmaker_Andra7 жыл бұрын
Awesome! Thanks for sharing this!
@АлександрРостов-т8в9 жыл бұрын
Я понял спасибо,а то я видел что края (гравировка что вы в начале делаете) потом её запалеровывают резинками,я тоже думаю что штихелем можно делать стекло.