KAGAMA 6S XP ROLLER 🔥 6S ELECTRONICS INSTALL & Must Do CHEAP + FREE Mods!🔥 Team Corally 2023 HOW TO!

#teamcorally #corally #kagama #rc #rccar #rchobby #rccommunity #rclife
Hi, In todays video I share with you my goto 6s electronics for the KAGAMA🔥🔥 I also show you how to install them.... step-by-step. My FREE & CHEAP must do bash ready modification are highly recommended for any 6s TEAM CORALLY rig💪 Watch and see what they are.....
I'm always happy to help fellow enthusiasts so just drop any questions you may about this or any other rig I own in the comments section👍🙂
Shoe goo 3.7oz
www.ebay.co.uk/itm/1743818859...
Extra sticky dry wall tape
www.ebay.co.uk/itm/2832999017...
Extra long battery strap
www.ebay.co.uk/itm/1551285003...
D3225 35kg steering servo
www.ebay.co.uk/itm/2555869611...
SPEKTRUM DX3 controller & S6200a reciever available from... Ebay seller - GRC Spares
www.ebay.co.uk/itm/1860499378...

[@AussieRCPlayground]

FYI, there is a slot under the front chassis brace for the ESC cable to run through. 😉 Nice trick with the Blu-Tack, not something I've seen before. How well does that hold up over time? I use double sided tape for my receivers, but using Bul-Tack to seal the box is pretty clever. Nice video and well explained and edited. Job well done. You got a sub from me. 😎👍

[@inspiredrc]

Thank you for stopping by vas👍🙂 thx for the tip. I will take a look at the slot for the esc wire👍 I do normally use double sided tape to stick the reciever down as well but was being lazy and thought the blue tack would prob do the job. I've used this blue tack method to seal the box for a few months now on my Kronos... I was desperate to find a way to wash my rig and not destroy the reciever... had to look for a way to seal the box but not make it permanent. It's work well so far.... only time will tell mate. FYI give my wing mod a try.... I noticed you broke yours on your last bash 👍👍

[@AussieRCPlayground]

​@@inspiredrcyeah, I'll give it go for sure. I like that you used washers on the screws, too. Should help spread the load and hopefully won't break as mine did. Good luck on the maiden run, I'm sure you'll enjoy this truck, it's heavier than the Kronos, but very durable. Also, keep an eye on temps... 😉

[@inspiredrc]

@AussieRCPlayground thx buddy. It could do with a heatsink and fan on the motor. I will keep an eye on them temps👍👍after seeing you bash yours i can't wait to get it out now 🙂🙂

[@donmistral]

Nice job !

[@inspiredrc]

Thank you 🙂

[@DozersRCPlay-vf4pd]

Yo!!! That is the best bash ready video ever. Great instructions with explanations. Hands on with details. Great editing and music. You deserve great success! Everyone has their own style and tweeks and details, but anyone following that video will have a killer rig set up to start! Great!!!

[@inspiredrc]

Thank you buddy👍 I make these type of vids to help the community. Hope you found it useful. I'm really happy you like it🙂🙂🙂

[@tomparker-455]

Done the same with silicone grease for the receiver box, heavily resistant to any moisture ingress

[@inspiredrc]

Excellent idea buddy. After losing a couple of recivers to water damage I had to come up with a temporary solution. Not had any issues after sealing the reciever box with blutac.

[@harryflow3270]

Great video as always 👌👌

[@inspiredrc]

Thank you brother👍🙂

[@gillian9178]

Great video mate, im still thinking about getting both the Kagama & the Asuga.

[@inspiredrc]

Thx mate. With the amount of changes they made on kagama I just couldn't resist adding it to the fleet... not to mention the price! 🙃🙂 the Asuga is also on my wish list... the first buggy with enough ground clearance for me to be able to bash!

[@DifalcoConcrete]

Awesome video 👌✌️

[@inspiredrc]

Thx buddy 🙂

[@danielkollatos5097]

Never rated spectrum transmitters ,bumbo best value for money

[@inspiredrc]

I am the opposite unfortunately. I have both...Not a fan of dumbo. I prefer the dx3. Just feels better quality.

[@ChriswithaCrc]

Hey buddy , You got a sub from me ! Some awesome little tips right there , Its two months on and how you finding it ? Stay awesome buddy Chris :)

[@inspiredrc]

Thx. Appreciate the sub chris👍 its a good stunt car. Lots of flips and tricks. It's prob one of the best from TC at the moment. Unfortunately not been able to get much air time due to weather but so far so good buddy 👍 with some 7075 upgrades it would be a complete tank!

[@timgoldsmith9126]

What pink Scrim tape is that? Better than the Orange Fibatape that you used previously?

[@inspiredrc]

Its around the same as the orange one imo. I just fancied a change of colour. There is a link to it in the description buddy.

[@timgoldsmith9126]

@@inspiredrcthanks! Was just about to buy some of the cheaper white stuff but don’t want it to not be sticky!

[@inspiredrc]

@timgoldsmith9126 defo go for the orange or pink... don't bother with white. 👍

[@Shellzwick]

So i ran my truck and the hingepin brace bent and my arm came out . I landed correctly too . I need a upgrade asap . Im not gonna waste my money on another trash one

[@inspiredrc]

Hi. I think M2C make a solid 7075 set for the kagama.

[@pukeylukey2852]

Theres noway u landed good..i Bash mines hard and i got no issues except the center diff locking up by itself🤗😅🤷

[@pukeylukey2852]

That's why just get tekno et48,mt410 or hobao hyper sste/pro ..those r straight up tanks

[@Shellzwick]

@@pukeylukey2852 I haven’t had the issue anymore . I brought it 3rd hand I think the previous owner messed up the hinge brace . So I swapped it

[@Shellzwick]

@@pukeylukey2852 it’s a strong truck now , all I did was upgrade the shock towers

[@Murphys_Law9]

First step is buy RTR version

[@inspiredrc]

Why would I buy an rtr when I would replace the servo, reciever and controller straight away.... not to mention I had a corally motor and esc available to drop in.... I saved at least £200 by getting the roller.