Nice presentation, subscribed. As for some protection, i use plumbers tape for the nuts, and clear sticker protection for the "key" spots for the body to avoid too much scratches and breaking.
@inspiredrcКүн бұрын
Thx dude. Great idea for the wheel nuts! I may have some plumbers tape lying around. Will try it next time. Any kind of reinforcement for the body will prolong its life. Luckily, these bodies aren't expensive. I tend to shoe goo all my bodies and have done for a while. Seems to help a lot.
@deadeyedetailing105711 күн бұрын
Bro are you up north? You sound like the blackburn / preson area?
@inspiredrc11 күн бұрын
Hi pal. Yeah, you're right..I'm based in Accrington.
@JJ-lu6mg16 күн бұрын
Definitely the best breakdown between the two that I’ve watched. I like that you didn’t rush through it. Keep at it I really appreciate you taking the time to do these reviews. 👍
@inspiredrc16 күн бұрын
Thank you. I'm really happy you found the vid useful 🙂🙂
@raidervic242820 күн бұрын
I bought this for mt Kraron 6s exb and it didn't fit. My wing is a one piece and doesn't have that removable center section. Any ideas?
@inspiredrc20 күн бұрын
Hi buddy. Sounds like you have the new version, kraton exb. Unfortunately, arrma has redesigned the wing, and so this wheelie bar doesn't fit. Unless you cut your wing mount, there isn't a way to attach. You could temporarily attach using thick zip ties. Still waiting for Arrma to release a new wheelie bar to the new version. I suspect it will come when they release the new outcast 6s exb.
@deadeyedetailing105724 күн бұрын
What skid plate are you using and body skids?
@inspiredrc23 күн бұрын
Hi buddy. I've got a set of Proline body savers on it pro6360-00 and a titanium rear skid plate made by CRCU (Custom Rc Upgrades) wheelspinmodels.co.uk/i/330535/?gad_source=1&gclid=CjwKCAjw74e1BhBnEiwAbqOAjI69TgOLkN0wrGjIEUVXSXiPSpOSXDWIvo6KqMvUmc3Fu6DyX7HRrhoCgKkQAvD_BwE kzbin.info/www/bejne/o3WZYYafjLqKetUsi=KEYOn9FEJeSV14eg
@keyriekalyan927329 күн бұрын
Can you help me understanding why my motor unit is solid red when switched on. No fan nothing. Only 2 runs.....new purchase. Unsure what happened
@inspiredrc29 күн бұрын
Hi buddy. I'm not 100% sure but flashing red is usually a binding issue, but I feel a solid red may mean the esc may be faulty. You do get 2 years warranty with all arrma cars. If you're in the UK, then I would give logic rc a call. They carry out all the warranty work for arrma and are very helpful. In the USA its horizon hobby.
@Facts-R-RealАй бұрын
Any update on how it’s holding up?
@inspiredrcАй бұрын
Absolutely amazing! I've not broken any pins since upgrading the hinge pin blocks. I don't like wasting money, but this is a must do mod, buddy. 👍
@PeterGreenProductionsАй бұрын
Very helpful, great video man, Thanks heaps❗
@inspiredrcАй бұрын
Thank you 🙂
@KUDRARACINGАй бұрын
Siiiiick
@M_i_n_d_W_a_rАй бұрын
😍👍
@jameswright5572Ай бұрын
Great run. I loved my 8s Outcast so much had to get the 8s Kraton to go with it. Both epic big boys.
@inspiredrcАй бұрын
Lol! I had to do the same, too... nothing compares to sending these huge rigs! 🙂👌
@BiffsEquipmentАй бұрын
HOW TO FIX XMAXX SPUR GEAR ISSUE.. Replace motor with spectrum 1250kv with the 8mm shaft (This is very important). New Aluminum motor mount to match the motor.. and mod 1.5 gears. Trust me.. Long as you do these 3 things and mesh it correctly your gear issues should be GONE. I dealt with this a long time and my issue was the stock motor.. the shaft was not only slightly bent but also the plastic motor mounts where they bolt to the factory plastic motor end caps on the stock motor would constantly loosen up just a tiny bit which would constantly change the mesh from too tight to too loose. Once I did these upgrades after trying everything under the sun for over a year all my issues were gone. Just be sure to get decent quality mod 1.5 gears such as the GPM Spur gear or other hardened gear matched with a GDS Pinion gear as GDS makes the best pinions.
@BiffsEquipmentАй бұрын
If any of you have issues where your mesh feels tight and then loose again and then tight again this is almost guarenteed to fix it. Also while your in there just be sure to double check all the screws on your cush drive ensuring they stay tight.
@inspiredrcАй бұрын
I agree, buddy. Flexing plastic is the main reason why gears get stripped on the xmaxx. Poor quality traxxas gears don't help also. Your solution it costly, but will fix the mesh issue for sure👍 unfortunately I couldn't afford to invest that kind of money in my xmaxx, so I had to find a cheaper solution. Tbh, the spectrum 160a esc is perfect for this rig. I actually have one ready to drop in my xmaxx. I have also had good luck with the gds mod 1 spur and pinion. Don't get me wrong, i am a fan of plastic but not everywhere on the car. I feel the motor mounts and spur assembly along with the front and rear differential housing should all be metal as standard. Just my opinion. 🙂 Thx for the comment, dude 👍
@jasonroth8507Ай бұрын
Thanks for the great idea. Had same issue on my son's notorious. Found old remote and now fixed and works!
@inspiredrcАй бұрын
Excellent... sometimes you don't need to overthink things. Simple solutions work too! 👍👍
@TMIVRCАй бұрын
Bro rn I’m on 30/39 gearing and it’s a monster lol I was gonna ask are the belted masher tires a good upgrade for it I already popped two tires 😂 what’s another good belted tire upgrade ?
@inspiredrcАй бұрын
Nice brother. I think the small spur is the way to go with kraton. Belted mashers or belted proline badland mx43 are peoples choice for the high gearing on this car. Personally, I like the look of the mashers over the mx43, but I think the mx43 may be able to handle the power better. I know some youtubers with 12s conversion upgrade opted for the mx43. I expect the bead-loc design will help keep the tire on the wheel. The badland mx43 are designed for the xmaxx though. I advise doing a little research to see if proline make a version that fit directly on the kraton. Failing that you can drill the centre holes out to fit the arrmas as well.
@TMIVRC2 ай бұрын
I bought both the Kraton exb and outcast exb 8s these things are animals the outcast is on another level hands down one of my favorite up there with the xmaxx I think the outcast is more fun but I think the xmaxx is probably more durable I recently put ear plugs in my Kraton diff just to see if it will give it more power and air control I’m surprised you are breaking stuff mine has been a tank so far just bent drive shafts lol
@inspiredrc2 ай бұрын
Hi buddy. New these 8s arrmas are tanks. Once the hinge pin braces start becoming worn out, the pins tend to break. It's an easy fix. Just upgrade to solid 7075 blocks front and rear. I found I broke more pins on the kraton rather than the outcast.... Could be down to the extra weight the kraton carries. Ear plugs in the kraton is defo the way to go👍 100% agree the outcast is SICK! love mine! I prefer it over the kraton. You do get used to bending drive shafts on 8s arrmas, unfortunately. Again, no big deal. Happy bashing!
@TMIVRC2 ай бұрын
@@inspiredrchonestly I can say it’s my fault lol I was testing the shit out of it and it took it the Outcast is an animal lol I’ll definitely do those upgrades what power upgrades do you recommend is a max 5 Worth It or castle ?
@inspiredrc2 ай бұрын
@TMIVRC I've always wanted to put a max 5 and 800 kv in mine 39/39. My only reservation is the extra weight it will add. I was hoping the 1100kv with the new v2 spektrum esc would be a happy medium. At the moment, I have v2 electronics installed in both of mine with 30/47 gearing and max punch. I can get a double backflip with the kraton, which I'm happy with.
@inspiredrc2 ай бұрын
@TMIVRC I prob wouldn't go with Castle due to the fire issues they've had in the past. It's just not worth the risk on £1000 rc. Hobbywing is more reliable imo. Also, if you upgrade the power system, then you will prob need to change the wheels. People tend to go with Badlands. Personally, I'm not a fan of the look.
@RICHIE_RICH892 ай бұрын
The cush drive is ruff but durable i like the slipper that came on the 6s and the driveline like it too 😊
@inspiredrc2 ай бұрын
If you stick to the stock electronics, the drive train on the xmaxx will hold up for the most part, but as soon as you upgrade, expect to start breaking gears. I went with aftermarket harden steel pinion and spur even with stock electronics. Something i feel traxxas should have addressed instead making cosmetic changes and calling the latest version an ultimate.....
@sunnyv12812 ай бұрын
Over heating issues ?
@inspiredrc2 ай бұрын
Not really tbh. I don't recall having many thermal cut offs. The car has been good 👍
@sunnyv12812 ай бұрын
@@inspiredrc I ask because I’m trying to find best gears for my xmaxx to run on to backflip and have good power without overheating
@inspiredrc2 ай бұрын
@sunnyv1281 At the moment, I've got 19/50 in my xmaxx. Just because that's all I had available in my parts draw. I haven't had any issues with it. I'm based in the UK, so the weather isn't usually an issue. Maybe that helps with temps as well. My advice is to try 18/46 and see how it performs, then maybe go up a couple of teeth on the spur. Really, it needs a max6 combo to make it come alive. You can even go 22/50 depending on whether conditions. To bash a big rig well, you want to get it to 50mph+ in my experience. I can get backflips on 18/46 though. 👍
@TMIVRC2 ай бұрын
I ended up gettting the exb 8s and outcast can’t wait to get them I had the kagama how do you feel about driving 1/8 scale lol
@inspiredrc2 ай бұрын
I love the 8s rigs, but they are heavy. Tbh I feel more confident bashing with the 1/8 scale. They are more agile and stunt better. Not to mention cheaper to repair. It's easier to carry around as well. Like you, I own both sizes, and that's simply down to the feeling you get bashing the 8s rigs can't be matched with anything else... So i will always try to have both 8s and 6s cars in my collection. 👍 trust me, your gona love your 8s cars when they arrive. Twice the size of the kagama!
@genreaper2 ай бұрын
Does the dry wall tape and shoe goo mod hold up well over time ? Good vid.
@inspiredrc2 ай бұрын
Hi. Yes. I've been doing this for the past 3 years, and I'm still on my original bodies on all my rigs. Although some are quite rough now. Highly recommended mod 👌 👍
@genreaper2 ай бұрын
Great vid Bro. Just ordered a K8s exb rtr and plenty of spares. On backorder till end of the month but looking forward to it but my bank account aint lol. Nice tunes too. Keep on Rollin 😊 PS: looks like could use some thicker centre diff fluid.
@inspiredrc2 ай бұрын
Thx buddy. I'm glad you enjoyed the vid. Bashing these big rigs is a blast. I'm sure your gona love your too! Yeh, stock they come with 20mil in the centre diff, but to stop the ballooning tyres, I think ears plugs are the way to go. I also recommend upgrading the A,B,C & D hinge pin blocks to aftermarket 7075 ones to avoid breaking loads of hinge pins. M2c and CRCU make good ones. Happy bashing! 👍👍
@conrow11572 ай бұрын
Any tips for servo upgrade? What servo and how to install?
@inspiredrc2 ай бұрын
Hi buddy. Tbh, I'm still running my stock servo. It's not as great after a year, but as a basher, I find a can go through servos often. To keep cost down I recommend the DS3235. It's cheap and powerful. Available on ebay and amazon. I have them installed in my kraton 6s exb and my kagma. Both are still going strong 💪 I actually have one ready to drop into the fireteam once the stock one fails. I hope this helps 👍
@conrow11572 ай бұрын
@@inspiredrc thank you mate. Any things I need to change on the mounts or servos horns or can I just replace the servo?
@inspiredrc2 ай бұрын
@conrow1157 hi. You will be able to use your existing horn and screws. Here is a vid I did when I put the 25kg version in my kraton 6s. Install procedure will be the same. Just make sure you get the 35kg version. Ds3235.
@inspiredrc2 ай бұрын
@@conrow1157 kzbin.info/www/bejne/f5m3d2yJd56las0
@conrow11572 ай бұрын
@@inspiredrc Hero
@rufusyoungblood92742 ай бұрын
💭🤔Best sound track ever made me go out and buy one 🤛🏽🦾💪🏽 🫡💯🔥
@inspiredrc2 ай бұрын
Nice one! Thx buddy. It's a super fun rig. Best 8s basher available today imo! 🙂💪🔥⚡️🚀
@AaronMiyok2 ай бұрын
Did it fix the range issues how far now hopefully normal again
@inspiredrc2 ай бұрын
Hi. Yes, it did help, but it also turned out that my steering servo was shorting out, which can cause all sorts of weired problems like esc resetting. Symptom was 'signal dropping', but in reality, esc was turning on/off by itself when i tried to turn left/right. My advice is only to re-trim the antenna if it's broken. Otherwise, look elsewhere for the issue, for example, possible water damage to the receiver....
@TMIVRC2 ай бұрын
What do you prefer overall ? Like if you could only get one which one would you get as your go to ?
@inspiredrc2 ай бұрын
Tbh the outcast is my goto. It stunts well and can ride the wheelies long distances and is fast. The new rtr electronics are the perfect combination between power and weight increase imo. I enjoy jumping my rigs and always am excited when I know I'm gona take it out.
@waynesleme74263 ай бұрын
That push away in the air and still landed it and saved your face from 8s burn out epic ..hell of a bash n blast spot .fine driving skills I have to say.
@inspiredrc3 ай бұрын
Thx Wayne.. it was a brutal first outing for the outcast. Yeah that jump could have ended bad for me. These 8s rigs are massive so you have the hit the jumps perfect or it go off course easily. I still love my outcast and glad you enjoyed the vid. I'm currently just taking a break from the hobby.... got lots going on at the moment but will be back soon. So far I love the new electronics. Prefect size motor for this rig and look forward to my next bash with the big girl! Tahir
@thepatternforms8593 ай бұрын
Out of the box stock will this wheelie easily? Punch setting all it needs?
@inspiredrc3 ай бұрын
Yes buddy. Max the punch and it should wheelie. I've added one ear plug in my center diff to get to flip easier but I was able to wheelie before I put the ear plug in as well.
@thepatternforms8593 ай бұрын
@@inspiredrc which is more fun this or the outcast 8s?
@inspiredrc3 ай бұрын
@thepatternforms859 Outcast 8s if your planning to jump and stunt it. Kraton 8s if your more of a track guy.
@thepatternforms8593 ай бұрын
@@inspiredrc I’m more of a high speed, drifting, guy. Which I know the K8 is better for but does the O8 turn sharper, handle better, and wheelie better? I’ve heard the O8 feels like more power and more fun?
@inspiredrc3 ай бұрын
@thepatternforms859 it's hard to decide which better hence why I have both. Personally the shorter wheelbase makes the outcast more fun. I can get a double backflip with the outcast where I only get a single backflip with the kraton on the same jump. The outcast wants to wheelie alot which make it difficult to get it to turn as the front wheels are always lifting up. If you like to do speed runs the kraton is better at it being more stable. I prefer my outcast as I like to jump my rc's and its more suited for that. Tbh from what you said the kraton will fit your bill. In the future you can ear plug the center diff to help with stunts and wheelie. If after that you still have the outcast itch it wouldn't take much to convert the kraton to an outcast.....
@westcoastsunrise78213 ай бұрын
Horrible music you ButtBoy!
@RandyandCyndi3 ай бұрын
I would love to test that as well
@Hungrybird4743 ай бұрын
Nice 👍. I was going to get this for the front and put the rpm one I have on the front in the rear .
@Hungrybird4743 ай бұрын
I need one of these or have another fin on standby but I think a bar would help offer a little more rear end protection ?
@inspiredrc3 ай бұрын
Hi buddy. The bar will give the rear wing some protection but the extra weight could compromise the wing brace... I drilled a couple of holes in the wing brace and added some zip ties between the brace and the rear tower. This stops the wing brace from over extending and breaking. I have a video showing this on the channel if your interested.
@G__Mason3 ай бұрын
Yooo that looks sick! There’s a dude selling one gently used for $375 right now and I’m trying my absolute best not to buy it 😫. I’ve just got too many, just bought a notorious 6s that I haven’t even ran yet lol. None of mine have a handbrake tho 😏 lol
@inspiredrc3 ай бұрын
Nice buddy. That's a good price for a fireteam. Mines fully upgrades to the exb spec bar the diffs.. however I'm running the stock 6s system ,15t pinion, max punch! I love the size of these and jumps well! 👍
@G__Mason3 ай бұрын
@@inspiredrc heck yeah, I’m the same way, that $375 will quickly be $700-800 within a week of me owning it lol. I suppose thats better than $1,000+ new tho, I like the size of them for sure but I’ve got some similar already so my question is, do you actually use the handbrake or is it just a novelty? That’s really the only thing drawing me to it, other than it looks badass, especially yours lol
@inspiredrc3 ай бұрын
@G__Mason thx buddy. Tbh I like jumping more than ripping so I don't use the handbrake much. Personally I think its a novelty. You can achieve similar handbrake slides with a good servo and fancy driving... don't get me wrong it's a nice feature to have but better suited to on road cars. It was the styling and roll cage i like hence why I wanted one for my collection.
@Hungrybird4743 ай бұрын
I have the ds335 coming for a Kraton 6s . Should drop right in ?
@inspiredrc3 ай бұрын
Yes buddy. I've still got one in my kraton.
@Murphys_Law93 ай бұрын
First step is buy RTR version
@inspiredrc3 ай бұрын
Why would I buy an rtr when I would replace the servo, reciever and controller straight away.... not to mention I had a corally motor and esc available to drop in.... I saved at least £200 by getting the roller.
@donmistral3 ай бұрын
Nice job !
@inspiredrc3 ай бұрын
Thank you 🙂
@tomparker-4553 ай бұрын
Done the same with silicone grease for the receiver box, heavily resistant to any moisture ingress
@inspiredrc3 ай бұрын
Excellent idea buddy. After losing a couple of recivers to water damage I had to come up with a temporary solution. Not had any issues after sealing the reciever box with blutac.
@TheThetruthmaster13 ай бұрын
It still doesn't stop wheelies
@inspiredrc3 ай бұрын
Sorry buddy this is not a drag race wheelie bar. It's designed to ride the wheelies. Not to stop them.
@TheThetruthmaster13 ай бұрын
That's a weird wellies bar.
@shawnscott97044 ай бұрын
Pretty impressive how it kept the bottom from being damaged
@inspiredrc4 ай бұрын
Its a simple solution but works well👍
@koryabel63194 ай бұрын
Got it thank you!
@avdeymocer29294 ай бұрын
🔥
@22bnightrider4 ай бұрын
Great job glad I found your video I did not like how the brake light was on the body thanks for your help
@inspiredrc4 ай бұрын
Thx buddy 👍
@danielkollatos50974 ай бұрын
Never rated spectrum transmitters ,bumbo best value for money
@inspiredrc4 ай бұрын
I am the opposite unfortunately. I have both...Not a fan of dumbo. I prefer the dx3. Just feels better quality.
@ivanstevanovic53724 ай бұрын
Is FIRETEAM more stable and more planted or is it just how it looks on the video?
@inspiredrc4 ай бұрын
Hi buddy. The fireteam has a longer chassis which makes it more stable and allows to drift easily. The longer chassis also makes it slightly more difficult to stunt. I would say the sledge is more bashing oriented where as the fireteam is more of a drivers car.
@polar7755 ай бұрын
what do you use to keep the RC's on the wall?
@inspiredrc5 ай бұрын
Hi buddy. I've just used some thick long screws with washers. About 8 inches long. I left the screws out the wall around 5 inches. Long enough to hang the cars under the front arms. It was temporary, not ideal but works. It makes the cars look as though they are driving up the wall. 👍
@rufusyoungblood92745 ай бұрын
Which one is the fastest stock right out the box with no upgrades
@inspiredrc5 ай бұрын
Prob the outcast as its slightly lighter buddy 👍
@fabricioaraujo67835 ай бұрын
Friend, please help me, I'm new to car modeling, I built an onroad car, with a 64pitch pinion with 40T, and a 64pitch 96T spur gear, I use a hobywing 10bl120a esc, the futaba 3pv radio has the end point at 100%, the 10.5T Brushless engine for 1/10 cars in the few laps I drove, the spur gear damaged all the teeth, how can I be doing so that this doesn't happen?
@inspiredrc5 ай бұрын
Hi buddy... sounds like the gearing material is weak. As long as the pitch of the gears are the same and the mesh is set right you should be ok. I would probably find some harden steel gears and replace the the pinion and spur.
@Ytytfytfujbyddutrxrt5 ай бұрын
FYI, this part doesn't fit the new EXB V2, as the spoiler has been redesigned.
@inspiredrc5 ай бұрын
Yes unfortunately but I expect arrma to release a new version wheelie bar when the new outcast 6s exb drops.
@imruss185 ай бұрын
how would you compare the kagama to the kronos?
@inspiredrc5 ай бұрын
Night and day buddy... kagama is superior 👍
@luvadealme5 ай бұрын
@inspiredrc is the kagama worth circa 170 quid more?
@inspiredrc5 ай бұрын
@luvadealme definitely buddy. The kagama is better built with alot more premium parts as standard...👍
@BigCheese855 ай бұрын
Thanks. I'll check mine. Off the ground mine turns right and left fine. On the ground it turns left fine but turning right isnt great.
@inspiredrc5 ай бұрын
Definitely worth tightening up. Mine been fine since doing this mod. 👍
@BigCheese855 ай бұрын
@@inspiredrc this didn't work. Shall I try and put a spacer under the spring? I don't understand really how that would help? Thanks
@inspiredrc5 ай бұрын
@BigCheese85 hi yes. I cut an old spring and added another ring to mine to stiffen it up. Yes I would put at least two or three spacers in.
@BigCheese855 ай бұрын
@@inspiredrc thanks. If I tighten the screw right down does it mean I could damage the servo if I crash?
@inspiredrc5 ай бұрын
@BigCheese85 yes buddy. The servo is there to take some of the shock from heavy steering and crashes. Don't tighten it all the way it needs some slack. As I said mines been fine... I'm still using my original steering servo after 3 yrs. It just a case of tightening a little then test it. Your steering will never be prefect because the traxxas stock servo isn't the best but you should be able to make it better. Have a look at my servo in the vid and try to match it....
@andrewgee56085 ай бұрын
I never could get instructions from them on how to install the wiring on the @Polocreations light kits for my Summit and Vorteks, fool me once, won't fool me twice. Not wasting my time or money on their scam products any further.