Kayaba (KYB) Final Drive Motor Cover Plate Removal

shop.finaldriv... 1-888-9-FINALS
KAYABA final drive motor cover plate removal
In this short video I will show you how you can remove the cover plate from a Kayaba KYB final drive motor. This is NOT how we remove it in our shop, but we get tons of calls from customers asking us how they can remove the plate in the field for inspection.
If you got questions, need a new or rebuilt final drive motor or final drive parts CALL US!
shop.finaldriv...
1-888-9-FINALS
We get you back on track
Click Or Call Us Today
shop.finaldriv...
1-888-9-FINALS
"we get you back on track"

[@BigDawgDavao]

Thanks for the video. Dealing with this exact issue at the moment. Will give it a go tomorrow

[@vinzergruz7893]

Hi yesterday I am dismantle Vio 27 travel motor than I flow your video thank you for guidance bro my name is gruz from Singapore

[@mikegamer6104]

Can you fix a small gehl excavator drive if I send it to you, I pop the cover and the top gears look good I can see some bearing parts and looks like one of the mid gears and bearing came apart

[@chggrup]

And whow you put it back?

[@ashbyw7755]

Great video. Thanks for a tip from the pros.

[@Finaldriveparts]

@Ashby Winstead, you are very welcome!

[@jnr2187]

Awsome work, Travis,

[@azentioced9]

to put it back together? how do you put the wire back in? thank you

[@AndR3uTz]

Did you manage to put the wire back in? Thanks

[@mickymanchester6400]

How do you reinstall the wire?

[@CanadianWoodworks]

Put the cover back on, then place about 3/4 - 1'' of the wire into the hole it came out of, it needs to extend into the same hole in the cover plate, once you start turning the cover plate it will catch the wire and start pulling it around as you turn the cover plate.

[@pistanek5279]

Hi, what if i cant turn the plate, its just stuck

[@ayvaztsagkir2134]

hello how do I remove the lid from a Takeuchi TB15 Finaldrive? It is from Kayaba and there is no wire installed. Thank you , Ayvaz

[@2027matsem]

شكرا جزيلا لك الحمد والشكر لله

[@nacho7604]

How much for a kubota kX41 2V

[@onemanandhistools9047]

How do you put the wire back in then

[@georgehofgren6123]

Yes, a follow-up video really would be helpful ~

[@AndR3uTz]

Great vid!

[@alatberat99]

good job.

[@CipOutoManual2011]

Thanks u kawan bermanfaat bagi teman indonesia mekanik 😀🤝

[@buddhikagunasekara5896]

buddhika gunasekara..hevy euqipment desel mechanic..srilanka.

[@jaboy123]

How do you get the large ring nut off once you remove gears and before you press it apart?

[@mrkrvn61]

again, great video.

[@Finaldriveparts]

Thanks, @Mark Ervin!

[@shirleytodd4967]

how do you replace the wire

[@francoroberto2388]

+Shirley Todd also i need to know how to replace it.

[@shanehayes118]

I removed the cover plate as described by Travis. I replaced the leaking floating face seal and reassembled the final drive EXCEPT THERE IS NO WAY THAT WIRE WILL GO BACK IN WITHOUT SOME SUPER SPECIAL TOOL. Any tips would be greatly appreciated. I am considering spot welding the cover plate on.

[@Finaldriveparts]

Hi! I'm forwarding your message to someone who knows the answer.

[@Finaldriveparts]

Got an answer for you! To get the wire back in you have to reverse what you see in the video, feed it in as much as you can and spin the plate in the direction that you want the wire to feed while applying a bit of pressure to it. Spot welding it in place would not be a wise fix for this.

[@shanehayes118]

Thanks to Travis and the guys at FinalDriveParts.com. I was able to re-install the locking wire, it only took me 3 hours! My tip is to feed the wire in where the notch in the cover plate is located. Moving the cover plate back and forward will pull in the wire about a half of one millimetre at a time. My KYB final drive was from a Yanmar vio 15-2 mini excavator. The access hole to install the wire is very small so the wire nearly goes in at a 90 degree bend. Thanks again, this job would have been impossible without this youtube video and the further comments provided.

[@valeriuszabados1650]

@@shanehayes118 And what if you drill a little tricky hole tangential to the wire track - i mean in the cast iron housing , obviously seal it after job done

[@GillesMarcoux-yu8ro]

Ou je peux commender les pièces

[@noelogara]

I have a locked solid plate and the wire is barely visible so cant get a tool on it.

[@Finaldriveparts]

I talked to one of our experts. Here's what he said: "He needs to get the tools to screw into the cover plate and turn it while feeding another wire into it to push the existing wire further out." And, if worse comes to worse, you could buy a new set of drives from us.

[@noelogara]

@@Finaldriveparts thanks. I'll try it.

[@danatimmermans6749]

need help uh025 Hitachi

[@Finaldriveparts]

What's going on with it?

[@danatimmermans6749]

@@Finaldriveparts Need parts for the final drive. Motor

[@danatimmermans6749]

i need the round seals the join the two parts togeather

[@Finaldriveparts]

Give us a call at 877-959-0620