Unreal edit bro ! Love the process and end product! Too sick
@AdvSouthAfrica2 жыл бұрын
I appreciate your comment Bryce! Thanks bro
@josearanda94276 ай бұрын
Hola compañero. Yo arme un KDX 125 sr igual modelo 1992. Que experiencia enorme poder armar ese motor tan poderoso. Felicitaciones
@AdvSouthAfrica6 ай бұрын
¡gracias mi amigo! Me alegra ver que otras personas también disfrutan de esta bicicleta
@soy_memo76117 күн бұрын
Realmente suena preciso!!! Eres un Mago,mi pregunta,que tan malo sería armar uno siguiendo el paso a paso,no soy mecánico pero me gustaría armarlo yo mismo, necesito un poco más de conocimientos
@furiousjammin19852 жыл бұрын
Question for you, i see conflicting comments online, and its hard to know who to trust. You race this engine so you know for definite the answer..... Which way round do you put your crank oil seals? Spring facing in or spring facing out? My engine is leaking and burning trans oil. Ive done the oil seals 3 times and still leaking. Just had apart and done a leak down test - the cylinder held 6PSI for 45 mins with no leakage now. Ive put back together and its burning oil again but no idea how or where from. All i can presume is the oil seal is strong one way, (holding air in the cylinder) but weak the other way and allowing oil through (like a one way valve if you like). I have my oil seals installed with the flat side facing inwards towards the piston (spring facing out). Which way do you put yours in dude? Thanks, Ben.
@AdvSouthAfrica2 жыл бұрын
Hi Ben! I can't think off the top of my head but I will go through some old vids and check for you. Are you using the correct sealer between the two cases?
@S2king-customАй бұрын
What’s the piston size of this engine ? Did you port the cylinder and all that ?
@lepeupleprendlemic3554 ай бұрын
Great job, Bro 🤙🏼🤙🏼🤙🏼
@AdvSouthAfrica4 ай бұрын
Thank you😁
@angus1298 Жыл бұрын
Hey dude, I'd love to see you do more interal type stuff, wicked bike have the same one but a 1999
@AdvSouthAfrica Жыл бұрын
Awesome man! I'll definitely film when I go into the motor again
@angus1298 Жыл бұрын
@@AdvSouthAfrica thank you! You got a Facebook or some other way to follow you?
@AdvSouthAfrica Жыл бұрын
@@angus1298 if you want frequent content then the best place is tiktok, KZbin I do more polished longer vids 😁 if you want to message me then Instagram is the one
@REVOyoutube Жыл бұрын
Is those original forks and swingarm?
@AdvSouthAfrica Жыл бұрын
Yes that's all original, including rear shock with linkage
@lizicskabela60962 жыл бұрын
Hi! I have the same bike but mine smokes too much i think. Can you please tell me your needle clip height and the air-fuel screw position?
@AdvSouthAfrica2 жыл бұрын
Hello friend! Are you still running the original oil pump? Unfortunately carb settings need to be tuned per bike. It's very dependent on your motor/fuel and altitude. Where I live we are at 1450m above sea level so my tuning would be very different to a coastal tune for example 😀 your bike may be injecting too much oil causing it to smoke a lot 😀
@lizicskabela60962 жыл бұрын
@@AdvSouthAfrica hi! I removed the oil pump a year ago maybe. I livebat 350-400m so as you mentioned it it would ruin my whole settings
@mkdmmkdm61229 ай бұрын
What jet size did you end up using?🤔
@AdvSouthAfrica9 ай бұрын
125 main jet but this is very dependent on the bike and altitude
@mkdmmkdm61229 ай бұрын
Thanks brother!!👍
@andyand100 Жыл бұрын
Thanks I’m off to look at kdx 125
@AdvSouthAfrica Жыл бұрын
Awesome!
@furiousjammin19852 жыл бұрын
also, do you run the full 800ml of trans oil or do you go half way up the window? What oil do you use? Its twisting my melon trying to get to the bottom of my trans oil burning issue. lol
@AdvSouthAfrica2 жыл бұрын
I think I run 750ml, it says on the side of my engine case. I just run a 15w40 mineral oil in mine. If you're burning transmission oil then chances are that you need to do bottom end seals. I redid mine at the start if the year because of that, hope it helps!
@hotrobban2 жыл бұрын
Nice!! What exhaust is it on Nike? It sounds reallöner good.
@AdvSouthAfrica2 жыл бұрын
It's a pincus racing pipe
@aurelschmid8296 Жыл бұрын
In which shops do you buy your spare parts?
@AdvSouthAfrica Жыл бұрын
I find parts online, no local stock
@furiousjammin19852 жыл бұрын
Hi. I dont suppose you have the 3D printing files for the KIPS actuator arm cover do you please? I need one soon as mine is cracked.
@AdvSouthAfrica2 жыл бұрын
I'd have to look, I printed it a while back 😀
@traehodges379610 ай бұрын
Do you know where I can get plastic fairing kit for this bike I can't find any
@AdvSouthAfrica10 ай бұрын
Apparently UFO plastics does some of them still but they are hard to find
@virangaumesh Жыл бұрын
Well done 👏
@AdvSouthAfrica Жыл бұрын
Thank you!
@virangaumesh Жыл бұрын
You're welcome
@aarifabdurrahmaan33652 жыл бұрын
Rare beauty 😍
@AdvSouthAfrica2 жыл бұрын
😎😎🤘🤘
@coffee51042 жыл бұрын
what kind of chamber is that is it a custom welded?
@AdvSouthAfrica2 жыл бұрын
It's a custom pipe, it's made by one of our local legends here in SA
@coffee51042 жыл бұрын
@@AdvSouthAfrica ooh okay, looks sick!
@AdvSouthAfrica2 жыл бұрын
@@coffee5104 thanks! It wasn't cheap but it's brought that motor to life 😀