I could watch that sawmill operate for hours. Homes and maybe whole towns would not exist without that sawmill. That boiler, steam engine, and sawmill made dreams come true.
@1DIYGuy9 жыл бұрын
I buildt a "tie mill" from scratch with scrap metal and a straight 6 chevy with the Chevy in 1st gear ran the mill using a foot throttle and by ear. I ran a 54" inserted tooth blade with half the teeth short to decrease load on the mill. Your 25HP mill has more usuable smother power than that 6 cylinder. Just a note in 1905 the inserted tooth blade was patented. Than you so much for the video.
@VintageMachinery9 жыл бұрын
+1DIYGuy Correct on the inserted tooth blade. Since our museum roughly represents 1890 to 1910, we are "period correct" to use it!
@antmallett60659 жыл бұрын
As a person who loves woodworking, machining and plain old fashioned ingenuity, this video is right up my street. Thanks for sharing.
@VintageMachinery9 жыл бұрын
+Ant Mallett Thanks for watching!
@juanrivero89 жыл бұрын
That was something to watch. It takes real skill to make boards from a log. All I have ever done is make boards with a chainsaw mill, and that takes a lot of preplanning too. To do it on the fly is mindblowing. Your sawyer is an ace. The steam engine is a jewel, over 100 years old and still running. Truly something to show the grandchildren. Thank you very much.
@VintageMachinery9 жыл бұрын
+Juan Rivero Thanks Juan!
@TomokosEnterprize11 күн бұрын
This is a really good mill producing accurate lumber.
@leviathan23859 жыл бұрын
Thanks for taking the time for a complete walk through/operation explanation. I love those old machines and I had questions. You answered them. I could just sit and watch it run for hours. Thank you Mr Rucker.
@VintageMachinery9 жыл бұрын
+Mynard Mayne There have been days when we were running the sawmill that a visitor would just sit and watch it run for hours. If I were not on the other side of the fence getting to work on it, I might be guilty of doing the same thing!
@jenniferford14313 жыл бұрын
How much is it for the atlas steam engine? Can someone please let me know
@duobob9 жыл бұрын
Watching your video is in many ways more up close and personal than an in person guided tour of the sawmill would be. Still, you have to be there to get the whole effect -- the noise, the smell, the hustle and bustle, the people, the wide view, etc. Thanks, Keith!
@VintageMachinery9 жыл бұрын
+Bob Korves No doubt that there is nothing like being there in person - it is a different view for sure!
@kspicer31323 жыл бұрын
The forward /reverse pulley for the carriage is still used today on most snowblowers. Amazing!
@calraines69318 жыл бұрын
Most enjoyable, refreshing fond memories of my Dad's love of all things Steam, primarily locomotives. He was a Director for many years serving the Pittsburgh Shawmut and Northern Railroad Preservation Society, a local road through his hometown of Angelica, NY. Dad was blind most of his life, but was amazing at what he could do. He'd have loved this operation! Thanks so much for sharing! All best.
@VintageMachinery8 жыл бұрын
+cal raines Thanks for watching!
@AnthonyFDeLeo9 жыл бұрын
Keith Thanks for the video. Around our area here in Northwest Washington State there were several similar saw mills, most converted to old model A engines or whatever they could scrounge up for power. Many mills later in life were used for cedar. These mills are now gone. Thank you for keeping these machines alive along with the spirit of those generations of men who operated them. Tony
@VintageMachinery9 жыл бұрын
+Anthony F. “Tony” De Leo Thanks Tony - it is a lot of fun to keep this old stuff running!
@PeterWMeek9 жыл бұрын
Liked the engine; liked the sawmill. Great video. Thanks for *all* these videos from the GMoA. That variable speed/reversible transmission was used in Norden bombsights (WWII). Instead of a wheel against the plate, they pinched a steel ball in a cage between the plate and a roller. The ball could be driven back and forth across the plate (they called it a disk) by a feed screw. Like the transmission, the distance of the ball from the center of the disk determines the transmission ratio. Each bombsight had three or four of them. Here's the cool thing: such a transmission can do calculus! In its bombsight role it's actually called a ball-and-disk integrator. It does integral calculus. You put one input into rotating the disk, and the other input into turning the feed screw, and the rotation of the roller is the answer. They were doing calculus in real time with the air-speed, altitude, wind (speed and direction), and getting answers that told the pilot whether to steer right or left, and to tell the bombardier when to drop the bombs. It made high-altitude bombing possible. I still have some of the parts left over after my dad salvaged shafts, bearings and gears from the half dozen of these things he bought back in the 1950s and '60s. I assume there are a couple of those ball-and-disk integrators buried somewhere in the tons of junk (sorry dad) that I inherited. I'm sure he didn't throw them away. (Growing up with access to his basement shop was really special. Thanks, Dad.)
@Wufnu9 жыл бұрын
+Peter W. Meek I just mentioned the calculus thing, too, before I saw your post! I love the mechanical computer series of videos on KZbin. They deal with trajectory calculators on battleships but still very interesting.
@antmallett60659 жыл бұрын
+Peter W. Meek That is truly interesting - any links to more info?
@PeterWMeek9 жыл бұрын
Wikipedia article: en.wikipedia.org/wiki/Ball-and-disk_integrator
@markfryer98808 жыл бұрын
You got to tinker with formerly Top Secret Norden bombsights! Amazing.
@gregorymalchuk2724 жыл бұрын
Too bad he disassembled them.
@swarfrat3119 жыл бұрын
Keith, That really looks like hard work! ... My family and I toured a sawmill a number of years ago. The had a machine that debarked the log. It then had lasers that "measured" the log to tell the sawyer where to make the cuts to get the most out of the log. He sat in a cab above the saw and carriage and pushed buttons and moved joy sticks to operate everything. A big difference a century makes! Thanks for the great video and for a look back in time. Have a good one! Dave
@VintageMachinery9 жыл бұрын
+Swarf Rat It is for sure hard work - particularly in the summer when it is 95-100 degrees! Not too bad when things cool down though....
@toddavis86034 жыл бұрын
BEFORE BANDSAWS and what a beautiful sawmill it is! Looks like a three-man money maker to me! 'From logs to lumber' was my presentation for teaching trade school in Queens NY.
@ChrisSmith-yx1iu9 жыл бұрын
i could watch that all day .. very cool , thanks for sharing Keith
@VintageMachinery9 жыл бұрын
+Chris Smith Thanks Chris - it is fun to watch. Even more fun to work in (except in the summer time....)
@ChrisSmith-yx1iu9 жыл бұрын
i bet it can get muggy real fast
@johnbazaar84409 жыл бұрын
So cool to see that old machinery run. State of the art 120 to 140 years ago. Materials, design, construction, operation, etc. 250 rpm was pretty fast for reciprocating engines back then. Thanks, Keith John
@VintageMachinery9 жыл бұрын
+John Bazaar Thanks John!
@simonanderson65948 жыл бұрын
I could watch and run that tool all day long, loved watching that run.
@VintageMachinery8 жыл бұрын
Come to the museum one day when we are running it and you can sit there and watch us work all day long. I have seen more than one visitor sit there for hours watching it run!
@simonanderson65948 жыл бұрын
I would but it's a long trip from Vt. Thank you very much for your videos. I appreciate the time and work you do.
@SuperBowser879 жыл бұрын
Wish I was there Keith! A long time ago I asked if I could run a board through the planer after the restoration was complete. You said come on down...... I just received for free a pickup load of rough cut walnut I could bring with me! Congratulations. The planer will be a great edition to your awesome Sawmill! Thanks as always.
@VintageMachinery9 жыл бұрын
+Tom Wilcox Thanks Tom!
@61066clocks9 жыл бұрын
Great video Keith, thanks For showing the operation,startup, and operation, of the Boiler , engine and Saw. Yea I have a early 90,s snapper self propel, that uses the flat plate friction drive self propel, multi speed, ..enjoyed Thanks for Sharing
@VintageMachinery9 жыл бұрын
+TIM WILSON Thanks Tim!
@Thunderstixx779 жыл бұрын
Thanks for the answer on the last video I posted a comment about being a shop teacher. It's really too bad that being a shop teacher isn't a field in demand. We need more shop people like you and Mike Rowe and fewer managers, lawyers and women's studies people in this world.
@paulmcguire37898 жыл бұрын
just enjoyed watching this again.
@TomokosEnterprize11 күн бұрын
I have a mill much like this. The carrige and husk were made by Couts in BC Canada. I used a mobile home frame cut and narrowed, A cable wrapped drum for the carrige drive and the original pulleys at each end. There are many other original parts and pieces. I used a 220 Cummins engine for lots of tourque and it suprisingly gets great fuel consumption. About 10 gallons an 8 hour shift. The original mill carrige came from the early 20's or late 1910's. I saw mainly for myself as finding 3 people that will work that hard is next to impossibe these days. It can make a fella sweat. That will never do in an age of button pushers eh!
@WatchWesWork8 жыл бұрын
This is awesome. There is a sawmill just like this one set up in Atkinson, IL. I saw it run maybe 15 years ago. I remember that friction drive. Very unique.
@michaelvangundy2264 жыл бұрын
I saw your channel and wanted to volunteer. I told my wife then she reminded me that I just like watching it. Thanks for the videos.
@venkatarr4 жыл бұрын
Well explained Keith bro. I love steam Engines👍
@JunkMikesWorld9 жыл бұрын
When I was a kid my Father cut down some trees from our property and we took them to a local sawyer. His mill was a much more modern one with ball bearings and a CAT diesel engine. At that time I never saw his mill run. However the lumber from those trees allowed me to build several projects at home and in shop class while I was in high school. I eventually grew up and became a shop teacher myself. I took 2 maybe 3 logs to that same sawyer and had them sawed into boards that allowed me to build much of the furniture in my home. He allowed me to come in with a video camera and film the mill running for my shop classes. I wish I could smell the pine being sawed. I imagine it smelled wonderful! The combination of the wood fire, fresh pitch and oil would be just heavenly!
@VintageMachinery9 жыл бұрын
+Junk Mikes World We still have lots of sawmills around here where I live - both big commercial mills and small mom and pop mills that will saw logs for the public. As for that smell, it is indeed a wonderful smell - at least to me!
@iancraig19519 жыл бұрын
a well spent 1/2 hr watching that Keith---I used to do a bit of timber milling as a young bloke and it brought back some good memories..
@VintageMachinery9 жыл бұрын
+Ian Craig Thanks for watching!
@davidhoward22379 жыл бұрын
Another Great video , Since i would probably never will be able visit the museum great to see all the stuff and learn about all the old machines, also for all those people who haven't saw last video were he talk on this and did some repair work search for Sawmill Clutch Repair: Part 2 - Broaching a Keyway, Reasembly, and Testing and 22 minutes in where showing again how it work
@VintageMachinery9 жыл бұрын
+David Howard Thanks David!
@rickl.orchids9 жыл бұрын
......had a wonderful time watching this, what a great show, thank you so much for taking the time.
@VintageMachinery9 жыл бұрын
+Rick L Thanks Rick!
@johnstrange67999 жыл бұрын
The mechanical ingenuity to move that much materail and mechanisim so effortlessly and with such precision is flat out astonishing. The scale on which the inventors of such machinery (and locomotives too) thought and created is beyond impressive.
@VintageMachinery9 жыл бұрын
+John Strange And it was all done without computers and for the most part, the "rules" that engineers go by today were not even known back then. They were some amazing guys for sure!
@johnferguson72358 жыл бұрын
I would hate to be operating that mill when the blade hits a spike or a large nail in the log. Both of those fellows are in the path of the pieces flying off the blade. It is wonderful to watch the old machinery at work, only dedicated craftsman can keep such machine operating. It is also important to remember the risks that our ancestors faced every day while at work. Thanks for the videos, Keith. I am officially addicted to your channel.
@VintageMachinery8 жыл бұрын
+John Ferguson I have hit more than one nail and even a few larger items (spikes, insulators, rebar, angle iron, chain, etc...). Because the wood is all around the blade and it is pulling everything down, nothing goes flying anywhere. But a bad crash will make you mess your drawers none the less...
@LogHewer4 жыл бұрын
Man alive. I want to work at this place. That setup is a sawyer's dream!
@luciusirving59265 жыл бұрын
The beauty of steam power and steam power is such underrated technology. That sawmill will forever be EMP proof and will still produce lumber.
@beboboymann38233 жыл бұрын
I love your videos and I have wanted to visit the museum for a long time. But alas Covid wrecked everything. I will be checking your schedules and definitely will visit you this fall. Thank you and your tea,m for all you do to preserve our history.
@garysmith97729 жыл бұрын
Wow, I could watch that all day, just facinating. one of your best videos, I would like to visit there someday to see that in operation. thanks. The start of the industrial America
@VintageMachinery9 жыл бұрын
+gary smith We would love to have you come by sometime!
@bentfork9 жыл бұрын
Awesome video Keith. Thanks for keeping the the old machinery going. It's great to be able to see how we have progressed since those days.
@VintageMachinery9 жыл бұрын
+bentfork My pleasure - lots of fun playing with this stuff, but I would hate to have to make a living running this equipment in today's world!
@martynnutland3234 Жыл бұрын
Fascinating, as always. The variable speed device was reinvented by an American called Hayes for automotive transmission around 1935. He sold it to the British Austin Motor Company. It was not a great success for a number of reasons, yet it represented a sophisticated early automatic system that deserved greater acclaim. Martyn
@AlfonsoTheTraitor9 жыл бұрын
I am so glad to see a steam powered sawmill up and running again,thank you for sharing.
@VintageMachinery9 жыл бұрын
+AlfonsoTheTraitor My pleasure!
@TYPE-zd3gm7 жыл бұрын
Another great video! I love how quiet the stationary steam engines are, it's cool to see and hear all the associated mechanisms doing their thing. Additionally, it's always interesting to see the ingenuity that went into the mechanics of these old machines. Thanks for posting!
@jenniferford14313 жыл бұрын
How much is it for the atlas steam engine?? Do you know
@JackHoying9 жыл бұрын
What a great tour/explanation of the workings of the boiler, engine and saw. Looking forward to seeing it in the very near future!
@VintageMachinery9 жыл бұрын
+Jack Hoying As am I Jack!
@chrisseats9 жыл бұрын
I've only seen bandsaw type mills work before. I'm amazed how fast that rips the logs! Great video!!
@VintageMachinery9 жыл бұрын
+Chris S They actually had bandsaw mills even back in the late 1800's. There were usually only found at larger sawmills though.
@walterplummer38089 жыл бұрын
I really enjoyed your explanation of how the whole system works. The swing saw is pretty scary looking. Thanks for another great video.
@VintageMachinery9 жыл бұрын
+Walter Plummer Yes, the swing saw is scary, but as long as the operator is careful, it won't hurt you!
@sandrammer9 жыл бұрын
Love to watch the old machines work. Good step-by-step explanation on the system.
@VintageMachinery9 жыл бұрын
+sandrammer Thanks!
@k1mgy9 жыл бұрын
Wow! Thank you for bringing this ingenious machine to life. It must be quite the experience to see it in action. I could watch this for hours.
@VintageMachinery9 жыл бұрын
+k1mgy Come on down and we will put you to work on it!
@k1mgy9 жыл бұрын
Maybe summer 2016. I'd like to visit the museum and have a look at your new shop. I was inspired by the tall trees! Thanks Keith for your work. It's great to have you take us along for the interesting experiences.
@80spodcastchannel9 жыл бұрын
so cool to watch the old ways at work.. thanks Keith. Seeya, Dude
Excellent presentation thanks keep up the great work team
@shade382119 жыл бұрын
I remember the new boiler make, but nice 2 see the whole run down. Thx
@paulshaw93559 жыл бұрын
that's one hell of a unit , enjoyed watching
@VintageMachinery9 жыл бұрын
+Paul Shaw Thanks!
@quantumss8 жыл бұрын
Thank you Keith, very well done.
@VintageMachinery8 жыл бұрын
+quantumss Thank you for watching!
@ianpostlethwaite49 жыл бұрын
Keith, an excellent video and very informative explanation of the boiler and sawmill operation. Thanks.
@VintageMachinery9 жыл бұрын
+Ian Postlethwaite Thanks Ian!
@ChrisB2579 жыл бұрын
Totally fascinating video Keith - love this stuff. For a modern facsimile that boiler is gorgeous, and really has that vintage look. Noticed Waynsboro PA on the firebox. The sound of that engine is classic... sure gets some RPMs going when you open it up. Great explanation and demo of it all - truly excellent video and thanks Keith.
@VintageMachinery9 жыл бұрын
+ChrisB257 The original boiler that we had was made by Frick, which was located in Waynesboro, PA. This boiler was pretty much an exact copy of the original with the exception of being welded rather than riveted. We even took the old original castings from the old boiler and put them on the new one.
@ChrisB2579 жыл бұрын
+Keith Rucker - VintageMachinery.org Thx Keith - that explains it! Old castings re-used on exterior - most successful.!
@slhasebroock6 жыл бұрын
Excellent tour of how it works! Thank you!
@frankcadillac91514 жыл бұрын
Thanks Keith this brings back memories. Back in the 80's I ran my circular mill with steam . Had a 8 1/2 X11" Ajax engine and a AB Farquhar boiler. My mill is half Chase and half Lane. I run it now with a Ford Dagenham diesel power unit. Up here in yankee land its tough managing the boiler in the winter. It seems to me theirs enough scrap in a log to power the mill to cut it. Nice to hear the chug of steam instead of the drone of a diesel.
@ErnieNoa39 жыл бұрын
Keith this was a great explanation of a steam engine and the saw mill. I liked the video very much.
@squareyes19819 жыл бұрын
I can't tell you how much I loved this video. Thanks for sharing.
@VintageMachinery9 жыл бұрын
+Ian O'Riordan Glad that you enjoyed!
@arlynsmith91969 жыл бұрын
Mr. Rucker this was really fascinating and quite well done! Thank you for all the hard work you do to teach and entertain your followers - it is much appreciated!
@VintageMachinery9 жыл бұрын
+Arlyn Smith Thanks!
@austinwagoncompany8 жыл бұрын
It was nice to see this machine working. I stopped by this museum on the way back from Florida in October 2015 and there wasn't much going on. the train wasn't running, the sawmill or the turpentine still wasn't either. I still had a great time though and plan to go back at a better time. I believe the guy I talked said that April is the best time to see everything going. It was just something that I wanted to see and after we left, we happened upon Juliette down the road that was used in the film Fried Green Tomatoes. BTW that town closes a 4:00 pm so we missed eating there too.
@VintageMachinery8 жыл бұрын
+austinwagoncompany What can I say, things are kind of slow down here in rural South Georgia! Saturdays are usually a good time to stop by the museum as that is when they run the train and we usually have more visitors on the site. The Folk Life Festival in April is the best time to come as that is a big event with pretty much everything running. That is the only time during the year that we actually fire the turpentine still.
@jincym89373 жыл бұрын
What a beautiful engine 🤩 thx for sharing 😊
@jeffdetwiler6 жыл бұрын
Great work Keith!
@brandonmcconnell81328 жыл бұрын
keith thats so cool i could sit there and watch till i die
@kevindownes21187 жыл бұрын
Very good video, helps you understand a little better, love it.
@pnwRC.4 жыл бұрын
I LOVE watching these old machines come to life, & do what they were intended to!
@nineringsh9 жыл бұрын
Another great video Kieth. thanks
@VintageMachinery9 жыл бұрын
+norm hays Thanks!
@billrick47298 жыл бұрын
As you were explaining the sawmill power train I was looking at those paper wheels and noting how they were just like my Snapper mower and then you mentioned that. I bought a Snapper around 1992 and it had a plate like that driven by a belt off the main shaft down by the blade. It had a wheel with a rubber tire that ran on that plate to drive the wheels, making it possible to adjust the ground speed independent of the engine speed. Still have the mower and it still works well.
@VintageMachinery8 жыл бұрын
Ironically, DeLoach patented the idea and Snapper copied it - the two companies were located pretty close to one another in Georgia, although at different time periods.
@AdrianHiggins839 жыл бұрын
well thought out edited video, thanks for showing something that I would not get the chance to see otherwise. hope you can do more like it. thank-you.
@VintageMachinery9 жыл бұрын
+Adrian Higgins Thanks Adrian!
@strykerjones88424 жыл бұрын
The carriage drive system is such a beautiful solution, I’ve never seen anything like that before. We truly stand on the shoulders of giants.
@roylucas10279 жыл бұрын
I enjoyed the video very much. The saw mill itself was amazing to watch. As far as safety goes, awaremess of yourself and your surroundings is key. Thank you.
@markfryer98808 жыл бұрын
Awareness of yourself and your surroundings means No mobile phones!
@zzzzzzzzzz37999 жыл бұрын
Cool Video Keith, thanks for sharing!
@VintageMachinery9 жыл бұрын
+G.J Bradshaw Thanks for watching!
@timambrass35219 жыл бұрын
So absolutely cool, Keith your a lucky guy!
@VintageMachinery9 жыл бұрын
+Tim Ambrass I count my blessing every day and getting to play with old machinery like this is a lot of fun for me!
@skeeter500019 жыл бұрын
Nice job. You have made a good productive machine out of one that most likely have been scraped. Good work.
@VintageMachinery9 жыл бұрын
+Skeeter Holeman Thanks - the museum has had this sawmill operational for probably 35 years now. I first started working on this mill back in the late 1980's when I was a college student.
@Rich206L9 жыл бұрын
Now that's what I'm talking about! Can you imagine the man-hours spent to make building lumber back then! Thanks Keith, that was a superb video. BTW, I guess that you can claim that, "No humans were harmed during the filming of this video because they were careful." Rich
@VintageMachinery9 жыл бұрын
+Rich206L According to the old literature, this sawmill was capable of cutting 10,000 board feet per day. I personally don't see how - I was running it one day when we came really close to cutting 2,000 board feet and that was one long hard day.... But with an experienced crew of men and a good sawyer, it was probably possible on one of those long summer days when you had 15-16 hours of daylight....
@Rich206L9 жыл бұрын
+Keith Rucker - VintageMachinery.org Wow, seriously?! JMJ, those guys must have been hauling ass! I also forgot to tag that last sentence in my reply with, "OSHA." :) You have one of the best channels on "TheTube" and I love every minute of it. Keep truckin, my friend! Rich
@ls20050192279 жыл бұрын
Thanks for another fantastic video. While many of the methods used to power the mills have changed (steam, tractors, diesel power units, & now electricity) many similarities remain. Band mills are becoming more popular, with a thinner kerf, smoother finish, and easier to hold a better dimension. thanks again!
@VintageMachinery9 жыл бұрын
+Robert Ross Bandsaw mills are the way to go in a modern environment. The kerf of the bandsaw blade is only about 1/8" as opposed to 1/4" on the circular mills so you are converting less of your log to sawdust and more to lumber.
@genefultz52679 жыл бұрын
Thank you Keith your video's are always so enjoyable !
@VintageMachinery9 жыл бұрын
+Gene Fultz Thanks Gene - glad that you enjoyed. Lots of cool stuff here at the museum that I have not had a chance to show you guys yet!
@srfurley4 жыл бұрын
I remember there being a steam driven sawmill in London still working in the late ‘60s or early ‘70s. I’m not sure exactly where it was, but it was alongside a canal, by means of which the timber was delivered. Sawmills did seem to remain steam driven longer than most other industry, presumably because they had plenty of sawdust and waste wood available which could be used to fire the boiler.
@billdlv9 жыл бұрын
Great video and explanation on the saw mill Keith. Thanks for the upload.
@VintageMachinery9 жыл бұрын
+Bill De La Vega Thank you Bill for taking the time to watch and comment!
@MrSpinteractive9 жыл бұрын
Fascinating (and SCARY) at the same time!
@gordoneckler45379 жыл бұрын
Keith, Thanks for a very good video presentation of the design features and operation of the steam powered sawmill. Enjoyed very much.
@VintageMachinery9 жыл бұрын
+Gordon Eckler Thanks Gordon!
@RoelTyros9 жыл бұрын
Hello Keith, First off all I will thank you for this great video and I never have seen an steam powered sawmill. Also great that you explained how it works and showed at last how they saw the wood. As a child I came often at the farm of an old friend of mine and I can remember that they had also a sawmill. But they powered the sawmill always with their old tractor who had also such a big wheel at the side like the tractor in the museum. Again many thanx for the great video and many greetings from Roel !
@VintageMachinery9 жыл бұрын
+RoelTyros At one time, lots of farmsteads had a circular mill like this. They were very common place back then!
@mertsilliker16829 жыл бұрын
Great show from start to finish. I just sold an Oxford mill to friend of mine. lumbering was and still is big here in altanic canada
@VintageMachinery9 жыл бұрын
+Mert Silliker It is still big here in South Georgia where I live, but not with these old mills any more....
@MattsMotorz9 жыл бұрын
Excellent video Keith!! I also use pinecones to start my foundry furnace. They do indeed burn really nicely. I have always been a big steam enthusiast. Steam engines are the singular reason why I built my home foundry and got into machining. I have been working on building a steam engine completely from scratch. Right now I am completely done with the top end. (2 inch diameter piston, 4.25 inch stroke) I've had SOOO many failed castings but eventually I got the procedure down to a science! Pattern making is particularly enjoyable to me because I like working with wood. The bottom end requires lots of cast iron castings, an avenue that is still new to me. But I am learning! I would also like to add (for those interested in steam engines) that in a steam engine, you get MUCH more torque because depending on the cutoff, you have constant steam pressure pushing down on the piston past top dead center,which is key because at TDC there is no mechanical advantage since the effective lever arm is zero. Max torque occurs when the crankshaft is perpendicular to the cylinder because it has the largest lever arm (Basically a cosine). Steam engines can provide CONSTANT pressure up to and past this point, providing a great amount of torque. Gas engines only have an initial pulse of pressure from the explosion, and the rest of the work is done by the EXPANDING gasses past TDC. The power from an expanding gas decays very rapidly as compared to a constant pressure gas. The doble steam cars of the 1920's are some of the most interesting steam engines you will see. The engineering put into them is truly amazing compared to the typical steam engines seen during that time.
@VintageMachinery9 жыл бұрын
+MattsMotorz Good luck with your engine. I have always kind of wanted to make my own steam engine as well, but with so many at the museum that we are using or need work, I have just spent my time working on those instead!
@tobyw95736 жыл бұрын
Jay Leno is a great Doble fan, as well as of Stanley. I highly recommend his videos on Doble and Stanley steamers as well as other steam engines and vehicles. www.nbc.com/jay-lenos-garage/video/1925-doble-e20-steam-car/2772940
@EasternExplorer7 жыл бұрын
That clutch system on the sawmill caught my attention because snowblowers up north here run on the same exact system! Surprised me! Just goes to show how old this technology actually is and hows its so good that it hasn't changed all these years.
@JesusvonNazaret9 жыл бұрын
I love this beautiful vintage machinery
@villeqq47899 жыл бұрын
I never really knew how steam engines work until now, thanks!
@VintageMachinery9 жыл бұрын
+Ville QQ Thanks - glad that you enjoyed!
@meyawabdulaziz38639 жыл бұрын
what a treat to watch.... ive got some of those 1880s and 1890 brass oilers that im retrofiring them to newer machines ..... not super into steam engines ,,,but i like the notion that these can work anywhere around the globe as long as there is water and something to burn .... wow that belt was rubbing against the bricks ....but it corrected it self seconds later ....
@VintageMachinery9 жыл бұрын
+Faisal Abdulaziz The belt that you saw on the bricks gets slack when the engine stop. When you start it back up again it runs on the high part of the pulley and is not a problem.
@meyawabdulaziz38639 жыл бұрын
oh okay thanks for clarifying
@outsidescrewball9 жыл бұрын
Great video, discussion & operation...thanks for sharing!
@VintageMachinery9 жыл бұрын
+outsidescrewball Thanks Chuck!
@gravedigr128 жыл бұрын
awesome to see her still going keep up the great work
@VintageMachinery8 жыл бұрын
+gravedigr12 Thanks!
@jimmilne199 жыл бұрын
Very interesting. Thoroughly enjoyed. Thank you for sharing. Great.
@VintageMachinery9 жыл бұрын
+Jim Milne Glad that you enjoyed!
@specialks19539 жыл бұрын
Excellent presentation!
@organbuilder2725 жыл бұрын
Interesting posting. You were quite detailed about the construction of the new bowler - the rivet decoration to retain the old appearance. Also the clearing of water from the cylinder and method of introducing oll for internal lubrication. There was a mill like this I saw as a child of 8 or so. They used the sawdust pile as fuel. It wasn't until the advent of gas and diesel engines that these piles were left in the forest where the stood for tens of years as tribute to the massive first growth trees that were cut Maybe a bit more detail on the carriage mechanism but it certainly made many aware of the old technology brought by the Industrial Age. Just a note to acknowledge your part in the restoration of these monuments to the enginuity of the hard working people 3 and 4 generations ago who built and operated a vast array of wonderful machines.
@Bigrignohio8 жыл бұрын
Watching you start up that boiler I was laughing quite a bit. Growing up there was a saw mill within walking distance of my house and my grandfather's farm. One of my strongest memories of the place (besides the creosote pit) is the huge piles of offcuts and bark-on slabs from the initial rough cuts. Those bits of "waste" were sold quite cheap as they had no use for them. Obviously what they needed was a boiler they could chuck them into! Although now that I think about it a full-time operation would generate far more wood waste than the boiler would require. I wonder if they used some of that waste to heat the wood treatment tanks? Next time I am down that way I should stop in and see. Assuming it is not an EPA Superfund site by now.
@VintageMachinery8 жыл бұрын
+Bigrignohio Lots of old sawmills and wood product plants burned their waste in big boilers. You can even blow in the sawdust and burn that. Even some of the modern mills still have boilers burning the wood.
@moto520009 жыл бұрын
VERY COOL! Thank you for sharing. Really neat to see how it was done.
@VintageMachinery9 жыл бұрын
+moto52000 My pleasure!
@shawnmrfixitlee64789 жыл бұрын
That just has to be the best video I have watched on a Vintage saw mill ..Love the steam power as well ! Thumbs up Keith !!
@VintageMachinery9 жыл бұрын
+ShawnMrFixit Lee Thanks Shawn!
@brad52exc2 жыл бұрын
My dad had a mill very similar to this one. It cut on the right hand side. The husk had an identical feed system. The carriage was 3 bunk and was set up exactly like yours. Our mill was made by J M Plante Co. in Ontario Canada
@max90689 жыл бұрын
Best Channel Ever! That's quite a blade, if it's a vintage blade what a revolutionary design. I kind of looks like a hybrid between a blade from a Lucas Sawmill and a modern carbide blade. Your channel is Awesome! Excellent video Keith!
@VintageMachinery9 жыл бұрын
+max9068 Thank - you could get blades back then with replaceable teeth, but they were a bit different than these. The teeth we use are steel and can be easily sharpened or replaced if damaged.
@davidwootton1639 жыл бұрын
Really interesting! Thank's Keith, this is very rewarding to have saved this machine from the scrap yard.
@grahamsengineering.25328 жыл бұрын
Thanks Keith. Love this. Very informative on the old ways.
@63256325N9 жыл бұрын
That was truly fascinating stuff Keith, thank you.
@VintageMachinery9 жыл бұрын
+Duncan “DunMac” Mac Thanks Duncan!
@LolitasGarden9 жыл бұрын
Thanks for the work you put into the engine, sawmill and video. It was a joy to watch. Truly ingenious engineering.
@VintageMachinery9 жыл бұрын
+Lolita's Garden Thanks - I am glad that you enjoyed!
@garyc54839 жыл бұрын
Great to see the saw in action Keith. Thanks for the startup procedures for the boiler and engine. regards from the UK
@VintageMachinery9 жыл бұрын
+Gary C Thanks for watching!
@shortribslongbow53129 жыл бұрын
Thanks for the tour it was very interesting. Keep up the great work.