Making Super Stable Bench Drill. 3D DIY Bench Drill

[@paulkuipers6988]

I made this bench drill after buying a 3D printer. My first project. Excellent drill for PCB's. Thanks for sharing. I added a led light.

[@bigdatapimp]

What was the rough cost for parts?

[@paulkuipers6988]

I only bought the sliders, barrings, springs, nuts and screws. That cost me about €30. I did not use all the bought springs, barrings, nuts and screws. I think when you have to buy everything, roughly €60 to €70.

[@Marbslab]

Very useful. Thanks for sharing.

[@zaferaltun]

Gerçek bir mühendissin, teşekkürler! Buna bir de PWM ile hız ayarı yapılırsa tadından yenmez.

[@PandorusFightStick]

this is awesome!! I need something like this with a b12 chuck for countersinking corners holes on acrylic!

[@lezbriddon]

Useful additions, 0.1uF cap across auto stop/start switch wires for contact arc suppression/RF reduction, and a snubber/filter across motor connections at top of motor to also reduce RF noise. This looks a good design.

[@jamshidshamuratov-vp4nw]

Your project gave me a good idea for my research work of study. Thank you very much.

[@serdaraydogan2329]

tekrar izledim tekrar yorum yapıyorum. çok ihtiyaç duyduğum bir araç

[@bahadrgergin6334]

Mükemmel işler yapıyorsunuz. 👏 Lütfen devam edin. 👍

[@mohamedaly6982]

All your vodeos .the best vodeos i see

[@teodulosoriano513]

This video deserve more views

[@jorgennorberg7113]

Fantastic attention to detail.

[@hasatcihazoter4283]

Başarılı ve kararlı oldu, tebrikler 🎉

[@ceryskebap5594]

Emeğine sağlık her çalışma mükemmel ayrı bir incelik.size zahmet birde mini turbo jet fan yaparmisiniz.

[@TengriKok]

sonunda beklediğim tasarım geldi teşekkürler. standartların dışına çıkılmış güzel bir çalışma tebrik ederim. buna lineer cross lazer gönyede taktın mı tadından yenmez.

[@duzgunisa]

üstad eline koluna sağlık.

[@serdaraydogan2329]

Aşırı güzel abi. Kesin ben de yapacagım aynısından. Eline sağlık

[@EEE-Cml-]

Güzel işler, teşekkürler çalışma için.

[@sdoksdomdiy99]

The best very brother❤

[@ibrahim-bi-lab]

❤çox yaxşı çlxıb əllərinə sagliq

[@dr_harrington]

WARNING: Before you sink too much time and money into this project, first buy the motor, drill chuck, and power supply. You want to test that you can run it at speed without wobble. If you have lower voltage power supplies (6V?) try those first and work your way up to the 10V power supply. If the motor shaft is bent, or the chuck is not concentric or balanced, then it will wobble violently which would be unsafe, much less usable. Assembly notes: 130mm red 16AWG wire from the auto start-stop limit switch to the power input. 150mm black 16AWG wire from the auto start-stop limit switch to the ON/OFF rocker switch. 320mm black 16AWG wire from the negative terminal of the motor to the power input. 190mm red 16AWG wire from the motor to the ON/OFF rocker switch. 1:34 M2.2x9.5mm screws to fasten the auto start-stop limit switch. 1:45 If you don't have M3x10, then M3x8 or M3x12 (with a washer) should work. 3:43 My motor did not come with mounting screws, but M2.5x10 flat head phillips machine screws worked. 4:46 Instead of glue, I used M3x30 bolts with two nuts (first to hold the bolt tight and the second to lock against the first) and a washer on the other side. 5:27 I used M3x20 with flat washer and lock washer and it still stuck out a little bit. M3x18 would probably be flush. 5:39 M2.2x9.5 works. 6:14 The through hole in the Elevator-Column-Top-part is only wide enough to fit one 16AWG wire. You'll need to widen that hole to fit both wires through.

[@Edmorbus]

Good work Thanks for sharing

[@intelligence482]

Nice work 👍

[@Isaac2IQ]

Good job 👏 Do you think you can make a video making 3D printed rc tugboat like Peter sripol

[@eragrafika6597]

ok tks for your information

Üstad eline sağlık. Daha önceki versiyondaki ufak kayma sorunları kaybolmuş.

[@МаксимК-б3к]

Хорошо получилось 👍

[@TheTriexy]

On your Prototype u can setup the speed before drilling on the final product not or did I miss something?

[@Kendin-Yap]

You can change the speed with an external voltage adjustable power supply. (7-12V)

[@TheTriexy]

@@Kendin-Yap Ah thx I was trying to understand what do you change between prototyp and final version. :)

[@ks2gamerz]

First comment

[@B_mata]

Thanks. I've been looking for a video like this. What infill percentage do you use for the printed parts?

[@Kendin-Yap]

www.rcpano.net/2023/07/30/making-super-stable-bench-drill-for-pcb-3d-diy-bench-drill/

[@riderxgaming8858]

Please make a plane with speedy bee flight controler please please ❤❤❤❤

[@Nazmi_PWM.C]

auto start-stop görevi yapan vaviyen anahtarının boştaki NC bacağına motorun diğer kutbunu bağlarsanız motor çalışmadığı konumdayken kutuplarını kısadevre ederek otomatik frenleme özelliğide eklemiş olursunuz.

[@burakkoc3439]

linklerde ürünlerin yanına kaç tane almamız gerektiğinide yazarmısınız farkında olmadan eksik alıyorum bazen

[@jw200]

I made one years ago. From metal rods, linear bearings and some printer parts. Now im making fully from metal. Its more stable and the drill will have literally 0 play. Which is must have for precision and such tiny drill bits. I can share video if needed.

[@EasyOne]

nice

[@nedimbuyukafsar6434]

👍👍👍

[@BTS-gr1hc]

Can you make airbus a380

[@EmirShahverdy]

Merhaba ben Azerbaycan, İranlıyım.Çok ilginç bir proje, Piyasayı çok aradım İran pazarında iki tip vagon olduğu için vagonun boyutunu söylemeniz mümkün mü? Lütfen tasarımın 3 boyutlu dosyasını bana gönderin ki tasarımın boyutunu İran pazarındaki parçalara göre değiştirebileyim. çok teşekkür ederim

[@Offroad_rc007]

🎉🎉🎉🎉🎉🎉

[@gouravtanwar636]

I thik you upload video on rc aeroplane but don't So I hope next video is on rc aeroplane and tell when will next video come

[@narayandasthakurraghav2943]

ये सामान का किट कहां मिलता है

[@BaranAvsar35]

kanalın ismine bakmasam türk yapımcı olduğunu anlamicaktım

[@naveengreen1]

can i get this in india

[@maaaadimataaadishakti422]

Price kay he bro

[@MEDKiT90]

Anadilin ingilizcemi hocam