How to make HIGH quality PCBs at home

[@mariomanus3176]

for quick prototyping, I now prefer CNC PCBs - as the process is much more quicker with more accurate holes. Been doing this and the photo methods before.

[@n00blord111]

Be rich, gotcha, good advice!

[@mariomanus3176]

@@n00blord111 i bought the cheapest Chinese knock off though, and did some low cost DIY upgrading.

[@edenassos]

@@n00blord111 "Be rich". You need to be rich to get a CNC? Go get a job, freeloader.

[@nagavenkatasimhachalam6357]

What is the toner transfer paper which paper sir and where is the availability please reply sir

[@bobbyd1961]

I'd be real nice if you spoke and explained each thing you did and what you were using. Like what kind of paper that was you printed on. etc...

[@alexandrubossro]

I was wondering the same

[@SurajGrewal]

I suggest not to apply any solder before drilling, since otherwise you'll have lead dust all over your room.

[@nickmuffin1722]

Exactly!

[@edgeeffect]

I'd drill first... but his holes do have no copper around them so there shouldn't be any solder at the points were he's drilling... an he does have a dust extractor.

[@Armand79th]

Only if you're still using shit like lead.

[@BeetleBuns]

as opposed to the more dangerous lead fumes already there from the soldering process?

[@dhupee]

Many people uses silver coating as opposed to solder coating I forgot the compound, silver nitrate or silver chloride

[@pjwarez]

For tinning, it seems some tinning fluid would be a lot easier than using a Soldering iron, and much better results as well.

[@SharvilSawargaonkar]

But you would accidentally close the holes with solder then you will have to drill again same thing

[@pjwarez]

@@SharvilSawargaonkar Tinning fluid does not close holes on the PC board. It just puts a very thin film of tin over the copper.

[@piconano]

Brought to you by JLCPCB!

[@staviq]

You can convert an old laser printer, to use instead of ironing iron. Laser printers have nice rubber rollers and a heater all built in and ready. I built one myself, it's super easy.

[@jovand6606]

you can use those paper plastification devices, they also have hot rollers edit: its called a Laminating Machine, they are vary cheap afaik

[@rahimsarvejahani2083]

Dear friend, what is the name of this paper?Can I use sticker paper instead?Because it is yellow like label paper

[@just-simple-I]

@@rahimsarvejahani2083 It's a type of photo paper. You can use any glossy paper. I used glossy paper from magazines when photo paper was unavailable for me.

[@jjjj-mu9rk]

what the nail polish use for?

[@just-simple-I]

@@jjjj-mu9rk He covered defected areas. I mean areas that paint hasn't been covered on tracks.

[@xavierr4508]

You are using polygons that go along some tracks, how is called that technique? I know how to use polygons, that's not the problem, but how did you got that final tracks' shape? Does it even have a name? Or I just add polygons at my own discretion? Thank you!

[@rahimsarvejahani2083]

You can design any shape in Altium Designer software😇

[@jeremiahrwells]

Great video, but can you comment on what ratio of citric acid to hydrogen peroxide...? Does it matter?

[@Chanchan1-k7q]

1:1 should be fine

[@techmatebolpur9252]

40% 60% some where 50 -50 % depends on copper plate quality and thickness

[@Shopeeka.]

Which paper did u use for toner transfer?

[@Rodrigo19602]

Hello. In my country (Brazil) it is called Glossy Paper, I think it is some type of photographic paper.

[@cyber38313]

Wow, very nice. What sort of paper did you use for the transfer?

[@wolvenar]

Search for "PCB Circuit Board Thermal Transfer Paper"

[@therealjammit]

We used to use the glossy pages from magazines. Don't use the cheap magazine paper, make sure they're the glossy type.

[@ami6packs]

@@therealjammit I'd never tried with magzine papers. I'd great success with glossy phot papers though. I'd never tried these thermal papers. I don't think I could find them locally.

[@rahimsarvejahani2083]

@@wolvenar Hello, dear friend, can I use label printer paper?

[@wolvenar]

@@rahimsarvejahani2083 Are you talking about the wax like paper that backs sticky type labels? I really cannot say, I have never tried. But it may work. I have used glossy paper from magazines, and glossy photo type printer paper with reasonable results with larger circuits. Magazine paper is not always good for fine (thin) circuits.

[@rodrigos.2099]

nice, gloves will help to keep the cooper clean/unoxided.

[@hmoudkhresheh1979]

Please what type of paper you used

[@LahiruNuwandhikka]

Which paper did used.

[@dmitrys711]

Why the tinning of the whole cooper surface needed? Isn’t the only places around the holes enough?

[@janithprabodha9125]

What is the name or type of the papers you you used to print?

[@mobilunik450]

Paper

[@Sana-en9ln]

The PCB turned out very nicely. And what kind of paper did you use that doesn't leave it on the paper?🤔

[@chukwukaobiano7498]

Great. Some what kind of Paper is that?

[@krawutzimon]

heavy metals don't belong into waste water, unless you want to make water treatment a lot more difficult and expensive.

[@wadebrewer7212]

Then cities should make the effort to dig up all of the lead pipes laid years ago and replace them. Besides....tell the people of Flint what this guy is doing is horrible.

[@stevenyoung4779]

You're using Sprint Layout !!! superb, my absolute all time favourite PCB software.

[@christopherwilliams1112]

Is the Sine Wave Inverter design you made the PCB for available online? Chris Williams

[@RalfHellener]

what is that for a paper? What is the name and from where can I get ?

[@eross21]

what kind of paper did you use to print this

[@DanielStingBR]

Nice you are fine man! I found white transfer paper, and yellow, is there a better?

[@Liam-j6y]

If you score the copper side with a Stanley knife using a ruler as guide you can then snap the board and end up with a prefect straight edge

[@sultanscience4912]

Would you share , what the brand of printer that use for, And what kind paper ? i want buy it

[@pic__l_]

5:19 what solution is that ?

[@sercosmico9166]

Thanks for the contribution friend, please tell me the type of paper used for printing

[@mp-uy9sv]

@Kasyan TV can you please make a "generalized" video about "how to" convert a three-phase tig welder into a single-phase please ? and also how to change the standard accepted voltages a welder is designed to run off into the voltage you require for your country /power source. As there are countless used cheap , powerful 3 phase welders available online that no one buys because 3 phase is rare and too expensive to get installed in residential houses, surely you know of a way to do these things

[@artursmihelsons415]

In place of citric acid and hydrogen peroxide, I'm using Sano kitchen cleaner cream and kitchens sponges scratchy side. After ironing, I'm dropping PCB in water and that transfer paper cames off by itself.. When pulling it dry, toner in some spots can came off because of PCB surface imperfections.. 😉

[@rahimsarvejahani2083]

Dear friend, what is the name of this paper?Can I use the yellow paper of the label printer?

[@RembertoMachuca]

@@rahimsarvejahani2083 Toner transfer paper

[@hugoegon8148]

Nice work, but tinning the whole PCB is very time consuming. What about covering it with a solderable transparent film like "Kontakt Plastik 70"?

[@hobbyelectronics6630]

Look up Liquid Tin by MG Chemicals.

[@RembertoMachuca]

@@hobbyelectronics6630 do you know if Super Shield MG Mechanicals can also be used? or which is better?

[@hobbyelectronics6630]

@@RembertoMachuca Super Shield is a conductive shielding paint. It will not work on copper traces. Liquid Tin is a liquid plating solution for copper traces. Two different products for different uses.

[@theodoreroberts3407]

Now, this is the density (though still small) I'm talking! How do you make a double sided board? I've done it, the old fashioned way. Lost some boards and I had a lot of acid to neutralize.

[@tbirdtelecaster7481]

Can you use an inkjet printer to print to the thermal paper, would it still iron on?

[@florinsfinx7614]

No...only laser printer

[@captain6198]

Is it a backpaper of adhesive label paper?

[@ami6packs]

What paper have you used? Please tell.

[@wolvenar]

Search for "PCB Circuit Board Thermal Transfer Paper"

[@ami6packs]

@@wolvenar thanks

[@JUANKERR2000]

What is the transfer paper, please?

[@nickmuffin1722]

The photographic paper which has like a plastic coating on top.

[@hobbyelectronics6630]

Toner transfer paper for laser printers.

[@huseyinhalitince4404]

it works printin inkjet or laser printer ? what kind of paper that used in printing. are they somewhat special

[@amx2]

If you now what is the kind of paper , please tell me

[@hmoudkhresheh1979]

Please what is the type of paper you used

[@mariomacinoi9065]

Hi, could you please let me know what kind of paper you used for the printer?

[@KAMALDEENAUSMAN]

the paper is thermal heat paper. now could you pls tell the name of the material he used. i am sure its not copper

[@pakkiarajahbaheerathan8280]

This PCB board design what softwear using design sir pl telme this drawing softwear name sir? Pl telme.

[@imranbehnam7428]

what is the name and type of this yellow paper please

[@pdrg]

Two quick questions - what was the nail polish for? Just to cover any imperfections? And which acid was that? Ferric Chloride is a lot darker and uglier, that almost looked like pickling vinegar!?

[@wolvenar]

I think they mentioned citric acid and peroxide. It can be used to clean the board by etching a small amount after soap and water cleaning to make a very clean copper surface. Also it will do the full board etch when left longer.

[@tiberiuoros9733]

Amazing... Very beautiful work.

[@qasimghouri2884]

Which printer you are using for this?

[@colombowala]

Any Laser printer at darkest setting

[@tobitezea8825]

Why did you use hydrogen peroxide and cetric acid to wash the board before putting in the PCB paper work

[@juliomamani3019]

Qué tipo de papel uso para el lado de dónde muestra la posición de los componentes con sus valores???

[@Enigma758]

What design software works well for single sided boards?

[@RembertoMachuca]

I use Proteus

[@coolchriss]

I believe this method is effective in case if we use all smd components, because drilling is going to take a century 😅

[@alfred536]

NICE the only thing that I didn't catch is what kind of board did you start out with and was that just a regular print from just an everyday printer??

[@hobbyelectronics6630]

Toner transfer paper on a laser printer.

[@jamesjohn2537]

Great work mate, keep up.

[@giuseperangel9647]

Helo friends! Can anyone tell you what paper is used in this process?

[@FreeTechLabs]

can you give the link to buy the Paper?

[@arielbene2013]

This is an ad video, showing how complex it is to make pcbs at home... Not explaining exactly. . And giving links to buy pcbs through them

[@lakshmansenevirathne2908]

which software did you use to create artwork?

[@rogeronslow1498]

With the low pcb price from JLC and many others and their 1 week delivery why would you want to make your own?

[@therealjammit]

"Printed incorrectly" Lol. We've all done that.

[@Etech47]

Nice effort to design PCB at home

[@hamidselectronics4863]

There is a thin transparent sticky sheet over these papers. Should we remove this before putting it into printer ???

[@Miniatures-And-More]

I Dont Think So , That Is Essential It Make It Non Stick So that When Heat Is Applied It Would Transfer It To The PCB

[@wolvenar]

Search out "PCB Circuit Board Thermal Transfer Paper"

[@luftstolle]

Oh my god, that's so much work. Sorry if I sound off-putting but this seems like so much wasted effort. And it's sponsored by JLCPCB which can make proper double-sided (or 4-layer) PCBs suitable for 0.5 mm pitch SMT components and plated vias and what not very cheap. By the time you finish the whole DIY method (which I assume also fail in some way regularly) you will almost have the finished PCBs in your mail box for just a little bit more money.

[@vvdvlas8397]

Приветствую! Что за бумага для перевода? "ведет" ли ее при нагреве?

[@SerjikM]

на алике продается. Термопереводная бумага для печатных плат. Распечатывать плату на принтере надо на определенную сторону. Вроде которая глянцевая. Бумагу потом не перегибать, тонер будет трескаться

[@albertsekyr8759]

Where do you buy the PCB board?

[@RixtronixLAB]

Nice video, well done, keep it up, thanks for sharing it :)

[@timernaut]

Thank you for sharing ! great video.

[@justinromang9113]

. cool printer - lov it - where can i get ONE *HP aka-01-kasyan* ....? hehehihi

[@quebuenavaina]

en el caso de Argentina un particular es dueño del subsuelo,? en otras partes el estado es deño del subsuelo

[@edgeeffect]

I love how you do toner transfer to get a "silkscreen"... that's nice. Also your "ancient" iron is fabulous. What concentration of Hydrogen Peroxide do you use.... I assume it's quite strong because of the relative "weakness" of citric acid????? In the UK, we can only get 12% peroxide as our government fear we will use greater concentrations to make missiles or something. I like Hydrochloric Acid because, as Nurd Rage taught us, we can use the resulting Copper Chloride as an etchant itself.

[@fivel256]

Developer at the beauty supply shop. But 12% is sufficient. Even in the US, anything greater than about 12% isn't readily available. We can get it, but it's a specialty item. 40 volume developer for hair color is 12% h2o2.

[@Andrelyx]

Что самое интересное я тоже думал наносить обозначения элементов таким же методом, нигде не гуглил, а метод оказывается рабочий.

[@SerjikM]

Тонер не проводит электричество?

[@Andrelyx]

Всё зависит от того какой тонер в картридже.

[@PK-nv4on]

Why applied lead ! It's an additional work and expensive. Anyhow soldering is done after mounting components...

[@amkp40technology]

Nice ❤️❤️❤️👍🏻👍🏻👍🏻👏🏼👏🏼

[@_RushiKansara]

please give this inverter circuit layout

[@AhmadRaza-di9qz]

WHICH PAPER THIS.......NAME OF THIS PAPER

[@omarkhaled3398]

Toner paper

[@driigo21]

Toooooooooppp 👏🏼👏🏼👏🏼👏🏼👏🏼👏🏼👏🏼👏🏼👏🏼

[@keithking1985]

thank you iv never made my own board but will save this to my favourites for when i do make one. THANK YOU KAYSAN TV

[@topgearIQ]

Type of printer .

[@solidhit2]

Great video, why is he using nail polish?

[@MatiGm-q8s]

Było można szpatułką. Są lepsze groty . ??? Trochę nie ekonomiczne - ale doceniam starania

[@bjbossjeffra3301]

how to download pcb layout pdf 200w

[@electronic7979]

Very good

[@hypnoticatrance]

A much better methode is to use PCB with a photo layer. Then print out with a laser printer on a transparent foliage. After this fix the foliage on the PCB and use a UV lamp.

[@jimmy_jamesjams_a_lot4171]

PAINSTAKING! When you tinned the copper with flux and solder! I don’t know which would leave less pollution or make less threat to personal health: dipping it in that expensive ‘liquid tin’ or doing it like you, with solder? I went the whole silk screen from photosensitive emulsion course, and really yours is probably even better. I don’t make proper stainless steel screens and stencils, just use the one they sell at the art shop for T-shirts. So whichever route you take in the end will be result of ongoing experiences, and always making use of what you have to hand in a makeshift manner. Thank you very much for sharing this!!

[@bjbossjeffra3301]

Send me pcb diagram circuit plaese🙏

[@aga5897]

Awesome ! I especially like the top side, with the component markings.

[@mody6762]

Good work schematic pls

[@mathr5255]

0:04 Glossy Photo Paper GP-401. Made in Japan 😧

[@MedSou]

*Good job* 👍👍👍👍👍

[@sarathai2876]

Wow , Very impressive. You rock

[@PradipKumar-xr4kv]

आप लोग video के लिये perfectly बना लेते हो Actual it is very difficult

[@rafi2437]

Co to za papier?

[@AKKJ420]

What are you using? why are you using? Would have been very helpful. This video has very little info.

[@Luismtz263]

paper of transfer thermal is the name of the papers use here

[@ananthe7up]

rf oscillator all frequency circuit diagram please video tell me

[@nickmuffin1722]

What exactly?

[@Steve-wx1gk]

Maybe you are really tallented👍

[@Посредственные_Проекты]

как называется эта чудо-бумага ? где она применяется ?

[@Harlequin43]

Так и называется - бумага для ЛУТ. Продаётся в радиодеталях. Но можно просто использовать страницу из глянцевого журнала.

[@Посредственные_Проекты]

@@Harlequin43 из глянцевого журнала не очень. я покупаю в копировальном центре, но её надо отмачивать...

[@rahimsarvejahani2083]

@@Harlequin43 Дорогой друг, что подразумевается под глоссарийным журналом?

[@sxpv]

@@rahimsarvejahani2083 just a page from any magazine, printed on a glossy paper

[@Choober65]

TBH, this is a good way, but given the time and mess, it actually works out cheaper to have JLCPCB make them. You get through hole, HASL, double sided, drilled boards for peanuts, AND they a perfect every time.

[@hyoenmadan]

Not for countries outside Europe and USA. In my country is still not only expensive to order, but also takes weeks to come.

[@hichamtassi1753]

@@hyoenmadan I totally agree, nice to see those adds, but useless for us...

[@Helal_Tech]

Wonderful

[@dimassetiaji2911]

when i made them all perfect......suddenly the factory create all printer "economic ink printing" ,including regular photocopy machines........which is made my PCB Lines goes many-many hole like a sponge !! !!.....WHAT A CRAP....BAD IDEA...........thats why you guys must patch it with TIN solder all over the pcb....a super crap.

[@conv2381]

No Voice ?

[@sharmashivanand]

High quality?

[@xfxox]

чё за бумага то?

[@KF-bj3ce]

Cutting a PCB with tin snips?