Kreosan, I love your projects, and I'm really pissed off about the people calling this fake. Apparently they've never seen a disc-on-rod wave guide and don't recognize a Yagi with circular polarization. Thanks for this video. I was going to design my own but you've saved me the trouble. And BTW, your translation called your insulator a "gasket" and now everyone thinks the reflector and driven element disk are shorted. Your biggest problem is that your audience is just ignorant and can't figure things out for themselves.
@olivejuice52334 жыл бұрын
Craig Wall but it is fake small little brat
@walkertongdee4 жыл бұрын
U never went to school eh, FAKE DUH.
@mojouk89354 жыл бұрын
You will get all the online weirdos who will get a hard on and counter this comment look above. Internet creeps we have now. lol
@alirezaeskandari22874 жыл бұрын
if you knew any thing about yagis you would not say so
@alirezaeskandari22874 жыл бұрын
they just turn on their phones hotspot
@wellboyscience84784 жыл бұрын
With 75 ohm cable you will not get better results Because most wifi adapters are rated *50 ohm* (VSWR is important(
@saadachab84254 ай бұрын
yes maybe your are right, but @Ath_ hace 4 años To everyone that says that it won't work: In america you obey laws of physics In soviet Russia laws of physics obey you
@capstasher4 жыл бұрын
This guy inhaled his grandpa's experimental internet gas.
@gabrielcoelho23464 жыл бұрын
Screentime!
@zyrppa4 жыл бұрын
At 9:01 that is GPS antenna, not wifi! Connect any metal thing to other end of the cable and results will be same.
@HelamanGile4 жыл бұрын
So basically They boosted their GPS a thousand percent.
@Thomas1124ful4 жыл бұрын
Any metal thing to the end of the cable? No, not really. While it might be still better than the internal antenna it will be nowhere near as good as the shown "wifi gun" antenna. And at the end they connected the cable to the correct pin.
@timsuttonlovinlife-4 жыл бұрын
Man I love this channel it’s awesome 👏
@fantomgaming90184 жыл бұрын
No that wifi
@111chicane4 жыл бұрын
Dumb!
@flyback_driver Жыл бұрын
Another way to find the center of a circle is to draw at least two (but more helps accuracy) lines of exactly the same length and touch the outside twice. For example if you have a circle with a 4 inch diameter you can use 1 inch lines so long as all of them are one inch. Then go back over each line with a square and at the halfway mark draw a line all the way through. Each intersecting line will also meet in exactly the middle .
@callmetony131910 ай бұрын
I don't know if this method is accurate enough for these kinds of use cases, but an easy way to find the centre of a circle is to pick any point along its edge, zero a ruler on it, and scan the ruler left and right until the measured length at the intersection of the ruler and the edge of the circle is greatest.
@yourelegantwaifu4 жыл бұрын
I want to see your video being reacted in Electroboom
@cjwrench074 жыл бұрын
You average kid The homemade wind turbine one, would be my vote for reaction video.
@IbraheemKhazbak4 жыл бұрын
THE RECTIFIER
@furonwarrior4 жыл бұрын
He mentions their video about the flying oil.
@yourelegantwaifu4 жыл бұрын
@@cjwrench07 this video especially. They got a lot mistake during the process and some of it doesnt even make any freakin sense
@nvmyutube4 жыл бұрын
its been done.....
@chrismin134 жыл бұрын
FIRST ONE IS 90MM NOT 80MM AS IT SAYS ON THE VIDEO! Had to cross check with the russian Kreosan video and it's 90, not 80. You can see it later in this video as well.2:38
@Abdullah-xz7ue4 жыл бұрын
that's right the original : kzbin.info/www/bejne/e4WVZqOkpdl9lZI
@vainboaster4 жыл бұрын
There is a Problem with the Two Disks that is connected to the stud without insulation thus shorting the antenna circuit. The second disk from the two disks that is connected to the wire should be insulated from the rest of the disks and stud...
@krunov9629 Жыл бұрын
no....update your antenna theory....at that frequency a galvanic short circuit is not a radio frequency short circuit
@cjwrench074 жыл бұрын
You need to add in links for the extra products you use. For example: the antenna cable to USB adapter.
@ssswasiim4 жыл бұрын
Yes, I agree with you
@Abraham2-95 ай бұрын
To get a better signal, I advise you to use copper for everything, including the pole. Also, the longer the cable, the weaker the signal. Therefore, if you do not need a cable with a length of 60 meters, then take what suits you, and the maximum is 100 meters.
@furekmody77494 жыл бұрын
I love how this car says "na berlin"
@alichank4 жыл бұрын
KZbin don't send me any notification. I have luck that i right now turn youtube.
@Drxxx4 жыл бұрын
Press bell notification
@supersolex4 жыл бұрын
wel thats because this antenna is fake
@alichank4 жыл бұрын
@@supersolex what this antena have to yt sending notification system
@youbetterbelieveit81144 жыл бұрын
🤔🤔
@mahmoudzidan74074 жыл бұрын
Hi Man can we make a metal detector like WiFi Gun Thanks
@aldrinmilespartosa15784 жыл бұрын
"No one can defeat the russian engine ring!!!!" - strohiem but he's russian
@timgore8294 жыл бұрын
You're probably losing most of your antenna's gain in that white coax cable. It's not made for 2.4 or 5 GHz frequencies. Also, is the driven element electrically connected to the reflecting element through the threaded rod?
@flyguille3 жыл бұрын
Yes, the same I though DC short cut!
@fungo66312 жыл бұрын
Satellite LNBs reach up to 2.1 GHz, so for 2.4 GHz a not too long cable should work.
@krunov9629 Жыл бұрын
cable for satellite receiver is good enough to 10 m
@dmo8483 жыл бұрын
I just can't stop laughing when he starts to go into town. Jus wow man
@franciscoestrada25523 жыл бұрын
Yes, me too
@flightgear11113 жыл бұрын
There are a few simple things you can do to make this even better. One, get rid of that cheap TV coax cable. Technically this antenna should be 50ohms impedance. RG6 ( common cable tv coax) is 75ohms. The mismatch will degrade this signal. Get some decent 50ohm coax. Second, you are using WAY too much coax. Microwave signals for wifi at best are weak, 50-70dBm ( a few milliwatts) the longer your cable the more the signal will be attenuated by the time it reaches your computer. Keep all the coax lengths as short as possible. Finally, the driven element of this antenna ( the 68mm disc you solder the center conductor of the coax to) this needs to be isolated from the boom ( the 8mm diameter screw boom used to attach the discs to) you need to put something on the boom so the 68mm disc is NOT physically touching the boom, like tape, heat shrink) the 68mm disc without this isolation is actually being shorted out. While it will receive some signal, if you isolated it from the boom it will work 1000 times better.......try it!
@krunov9629 Жыл бұрын
no need to be isolated.....try you theory before comment.....this is exactly as suppose to be, this is not short for 2.4 GHz, not even close
@seanmayoaguirre13164 жыл бұрын
Dude, I don't know what's cooler - the awesome sci-fi looking death ray wifi gun or the green automobile...I WANT THEM BOTH!!! Cheers, man. y'all are geniuses! If you came to Los Angeles you could probably trick the whole city into thinking you are INTERPLANETARY WIZARDS. Stay Groovy, Dudes. I Love the Videos!
@dt8869 Жыл бұрын
Super video! How (using which application) did you calculate the dimensions (diameters and distances) for making the antenna?
@KetansaCreatesArt4 жыл бұрын
I love this wifi pushka 🤗
@lordelectron65914 жыл бұрын
Does it push wifi
@dangerousdoggo54654 жыл бұрын
means rifle
@adorhambre5973 жыл бұрын
all content of these channel are true unlike other yt channel. love it.
@hotboy1979883 жыл бұрын
It should have shielding between the contacts from the outside ground to the copper centre. If you was to do this on say a CB or Ham radio you would burn it up without shielding. I believe the low watt wifi could suffer from long-term use without making the rear shielded from the front over time.
@krunov9629 Жыл бұрын
it is not critical on this freq....
@benjaminwesp75842 жыл бұрын
I have build your Wifi-Antenna the way you told in the video. I am impressed! Instead of cupper i used aluminium but everything else remains the same. The quality of this antenna is unbelievable good!
@RahulSharma-ue6sg Жыл бұрын
Hi @benjaminwesp7584 Could you please tell the the latency difference with an without using antenna, and As we increase distance don't we need transmitter and receiver both to be high gain antenna ?
@Placa_9Ай бұрын
Hi! Did yo use the long coax tv cable too?
@thomasvnl4 жыл бұрын
One of the most powerful wifi adapters: no its just el-cheapo. Also nice job connecting the antenna to the GPS port of the tablet
4 жыл бұрын
Thomas Verschoof, it is directional.
@sirhaugen10254 жыл бұрын
No! You have to isolate the active part from the ground. This antenna is useless without.. making the antenna like this it will be a short between active element and ground...
@Fortnite-gb7dz4 жыл бұрын
No this is like a magnetic loop
@Fortnite-gb7dz4 жыл бұрын
Even a biquad antenna has a short
@sirhaugen10254 жыл бұрын
Nicolas Springer : No. A yagi antenna is nothing like a Biquad or Magnetic loop.
@MrDarkLung3 жыл бұрын
Soviet Sheldon Cooper 😃 Awesome!
@johnhoye65843 жыл бұрын
Sheldon cooper was a theoretical physicist. Probably could not use a drill.
@DaleK-j9g3 сағат бұрын
kreosann.......hope every thing is ok in your location.....i like your car too....i drive a 1968 Mercedes Unimog here in the US...keep up the good work...stay safe
@Kj16V4 жыл бұрын
5:58 Waaaaaiit... Haven't you just shorted out the entire aerial to just two discs?? Aerials confuse the hell out of me!
@edgarbjorntvedt4 жыл бұрын
This is what I think as well. I think this second disc must be isolated from all the other ones to make the antenna work as expected
@krunov9629 Жыл бұрын
no.... it is just like supposed to be....dc short is not short on 2.4 ghz
@boubacartahirou91903 жыл бұрын
hello I really like your videos. I have a question between iron, aluminum, copper and zinc which brings more signal?
@kitecattestecke23034 жыл бұрын
Nice GPS antenna on the tablet ;-)
@Abraham2-95 ай бұрын
To get a better signal, I advise you to use copper for everything, even the column
@dtesta4 жыл бұрын
Seriously, with that long cable, you would loose all the gain you might get from the antenna. I smell fake. When you make these kind of USB-adapter-type antennas, you should use a long USB-cable and attach the adapter directly to the antenna itself, to get the shortest possible antenna cable.
@DavidLopez-bz4rj4 жыл бұрын
Yes, it is a great fake. The antenna cant work at all. They lack of basic knowledge of antennas.
@craigwall95364 жыл бұрын
@@DavidLopez-bz4rj Apparently you're ignorant of disc-on-rod wave guides. This isn't fake. Put another way, this is a Yagi with circular polarization. It is _you_ who are ignorant of antenna knowledge.
@craigwall95364 жыл бұрын
Silly you. They've left the cable long because it would be stupid to cut it until you decide where you want to INSTALL it. AND because if it works at all, they know that it will ONLY GET BETTER when the shorten the coax. They're EXPERIMENTING. They aren't stupid and you haven't told them anything they didn't already know.
@DavidLopez-bz4rj4 жыл бұрын
@@craigwall9536 You are the one who doesnt know that circular pol has a penalty of 3db versus linear pol, so silly is using it for wifi. I am a ham radio operator and I use a homemade antennas since 25 years. I can reach my home with my smartphone from 2km away, I have internet all around my valley. This antenna design is old as hell, you will never see a yagi design with evenly spaced elements. It is a piece of shit, I reach more with my microwave oven hahah
@digitalmediafan3 жыл бұрын
8mbit speed is rather slow these days bit like dial up 20 years ago and isn't it illegal to connect to someone's wi fi ?! But a great project though
@OldisGold-tp1xk4 жыл бұрын
Please provide buy guide of the things used and simple map of it
@barrosvinicius4 жыл бұрын
Congratulations. Jajaja quiero hacer esto también viva la WiFi Free
@blise518B4 жыл бұрын
Isn’t that just a short circuit of the antenna cable? There should at least be an insulation between the last disk and the central screw?
@Jorissoris4 жыл бұрын
No, that's not how antennas work. Just like in a Yagi-Uda antenna, it does not matter whether the directive elements are connected to the central boom as the electric field is (supposed to be) almost zero there
@blise518B4 жыл бұрын
Ty for the explanation. Very interesting. I always thought there have to be 2 elements were a voltage difference can be induced or something like that.
@Jorissoris4 жыл бұрын
@@blise518B You're not wrong! The point is that due to the speed of light and the very high frequency of Wi-Fi, there can be a voltage difference even though the elements are not insulated :)
@craigwall95364 жыл бұрын
No, the NEXT to last disk. And the insulation is there but the translator called it a "gasket". (The last disk is the "reflector" and the next to last is the "driven element".
@Jorissoris4 жыл бұрын
@@craigwall9536 There is no insulation there. The narrator called it a gasket but it's clearly just a metal spacer
@electronresonator88824 жыл бұрын
7:48 ha ha ha...now those Americans know that you guys are out there breaking their internet, lol
@awanyuniawan18424 жыл бұрын
Its work don't judge please
@girlsdrinkfeck4 жыл бұрын
@@awanyuniawan1842 it dosnt work, same bullshit video their free electricity video was bullshit
@Танкист-ц9ф4 жыл бұрын
Куда я попал Ахахпхах 🤣🤣🤣🤣 Оказывается есть канал инглиш креосан
@Мойевропейскийжидобандеровский4 жыл бұрын
И немецкий есть, только длхлый
@guanip4 жыл бұрын
suoer excelente, felicitaciones a tu canal, desde venezuela.. es ingenioso las ideas q tienes y eso me gusta ya q aqui en venezuela es dificil conseguir poder de señal.
@bebox4 жыл бұрын
hi, great fun with your videos as usual. can you give us som links for : antenna adapateurs and routeur that accept USB device as source on internet kind regards from France :)
@verynice.mp46134 жыл бұрын
Stéphane BeBoX its being translated i think kreason doesn’t even know this channel exists lol
@ParadiseParadises3 жыл бұрын
RF Coaxial SMA Male Plug to BNC Female M/F Radio Antenna Connector Adapter
@lostjohnny90004 жыл бұрын
You can buy RF pigtails from drone suppliers. UFL and smaller IPEX4 types to standard SMA Wifi cards now use IPEX4 but older cards before around 2016 used UFL (IPEX1)
@DiyEcoProjects4 жыл бұрын
*Kreosan* improvements for you. I read somewhere, to isolate the 68mm disc from the central bolt by putting heat shrink tubing on the shaft. That way you are not creating a short. I dont know if that is correct, just trying to help. All the best guys, youre awesome
@EzeePosseTV4 жыл бұрын
I was just thinking that when he slid the disc connected to the coax screening along the bolt connecting the coax center wire to the next disk without insulating the screen disk. Basically just rendered the rest of the antenna beyond the center wire disk useless. I remember making a CB radio tranceiver out of coke cans in much the same way as Kreo except my antenna was 22 foot high and took over an hour to tune the SWR in properly, lol
@d1s1ntegrator564 жыл бұрын
It may be AC isolated, but not DC. If a modem or other device outputs DC current to antenna - it is going to short out and you can damage device.
@krunov9629 Жыл бұрын
no no and no....there is no dc and galvanic short is not rf short ...design is good ...why is such many wrong comments on that ? check commercial antenna of same design
@shakibm15584 жыл бұрын
Anyone tested the speed over like 300-400 ft (120 meter) distance? Would the speed be increased if both sides are using similar antenna?
@NewLife-jw9to4 жыл бұрын
Thanks for visiting 🇮🇳 India 🇮🇳 I have seen ur video on hacker OM channel And thanks for the this video 🙏🕉🙏
@NewLife-jw9to4 жыл бұрын
@Tushar Kashyap I said about hacker OM Aur Indian hacker bi hai we can get the knowledge But it's true that they just want views What do u asspect when ur an KZbinr 🙏🕉🙏🇮🇳
@NewLife-jw9to4 жыл бұрын
@Tushar Kashyap haa king of random bi Accha channel hai Aur recently Indian hacker nay chloroform par ek video banaya tha Jo k bhout Accha tha Warna hum to chloroform ko Galat Tara say Samaj rah thay U know by watching the movies like de Dana dhan 🙏🕉🙏🇮🇳
@emptech4 жыл бұрын
Antennas like this one have been used for many years. It is called a disk Yagi or a surface wave antenna.
@tony5226 Жыл бұрын
🤓
@BeatboxNorwich4 жыл бұрын
The shield and core shorted out, a mile of 75 ohm coax cable with no balun. Seems legit!
@Gamer-nc8qp4 жыл бұрын
i was wondering that too its not insulated
@DavidLopez-bz4rj4 жыл бұрын
Hajaj, yes it is fake.
@craigwall95364 жыл бұрын
It's not shorted. The translation came out "gaskets" when they meant "insulating washer". And no, it's not fake. It's not even new. This is very old technology.
@BeatboxNorwich4 жыл бұрын
Oh, OK. Cheers for that, Craig :) A few of their vids have been called out as fake so I made an assumption.
@denz374 жыл бұрын
nah u got it man
@djatomist2 жыл бұрын
I had a Cisco Yagi in ~2004 where I was living very close to the pentagon. While trying to pick up free wifi I had it mounted outside my house pointing into the direction of the pentagon. A black SUV pulled up with 2 people in black suits jumped out, took a bunch of pictures. Then they got into the SUV and drove away. Never heard anything from them.
@Richard_GIS4 жыл бұрын
7:38 MegaBITS of course ;-)
@furonwarrior4 жыл бұрын
Would of advice, TV coax uses 75 ohms. 50 ohm coax works better.
@sterben19414 жыл бұрын
Thank for this idea adopting the Yagi Uda antena. Hope you make signal/internet booster to those users who are only using mobile data internet/ users of Free and Paid VPN, no wifi, and the eqiupments are accessible at home because we cannot go to hardware store due pandemic and our age limit restriction.
@wdtripps65374 жыл бұрын
To get around Wi-Fi passwords you also need Linux, aircrack(or another type of cracking software) and one other thing I will keep to myself. In 15 minutes with a mediocre set up almost any Wi-Fi password can be compromised. This guy is legit.
@allandulles71083 жыл бұрын
Theres plenty of windows cracking software too. Linux is a pita.
@CBKCUSTOM4 жыл бұрын
I love this channel i idolize you sir i want to be like you someday i wish you will visiy philippines and have a vacation here
@oddjobbobb4 жыл бұрын
That car looks like a 1957 Fiat 600D I owned. Suicide doors too, nice.
@gordslater4 жыл бұрын
Zastava 750 i think, so a licence-built 600
@becconvideo4 жыл бұрын
Saporoshez SAS 965 . Made in Ukraine. The original Fiat Seicento stood model for its body but the engines are different- the Sappo has a V4 while the Fiat runs on inline 4 cylinders giving more space to rear passengers in the ukraine model. They were quite common in East Germany too but then less popular than the Trabant. (I don't know why, I haven't driven neither) Now collectors items due to their scarcity,
@legencyblue23302 жыл бұрын
In mountains why can't it be bigger plates for internet? Good learning you do.
@pranitkhedekar23884 жыл бұрын
7:49😂
@GabrieLight3 жыл бұрын
I made one to hack the pentagon as you suggest, but there's a message appear saying “there's no pentagon available in your country” How to fix?!!
@michaelc.2674 жыл бұрын
To Kreosan, I would like to invite you to Italy, Sicily to meet an Engineer friend of mine, I want to create some great devices to sell are you and your team available?
@fizhbing4 жыл бұрын
Help, mine isn't working
@BurkenProductions4 жыл бұрын
What?? The ground is shorted to the antenna ??? How could that work
@lordelectron65914 жыл бұрын
Maybe he insulated the discs?
@lordelectron65914 жыл бұрын
@@lands1459 Wait that means we get wireless free energy?
@lordelectron65914 жыл бұрын
@@lands1459 Can these rf signal be converted to dc? BTW thank you
@steampunkfox14116 ай бұрын
One thing I am hitting a snag on: My cable had a totally different end so i cut it off to get at the tip.... does the thin wire in the middle have to touch BOTH the first two plates or just the second?
@gabedaxe66224 жыл бұрын
I’m here for the creen car 🤣
@TerryDeSimone3 жыл бұрын
What material are you using?
@zikomusic66674 жыл бұрын
Amazing chanel
@trading.and.investments4 жыл бұрын
Подходит ли это для захвата лучей сокровищ под землей?
@anthonyg46714 жыл бұрын
Clever, but you need to fix your clock :-)
@steviebboy694 жыл бұрын
Nothing like getting free wifi if you dont have or cant afford the internet. What sort of car was that, the motor at the end looked like a VW Bug engine. nice little car reminded me of the Leyland Mini Clubman I once had.,
@artemikf4 жыл бұрын
Когда на основной канал выйдет ролик про чернобыль
@peppapigofficialspoiler12904 жыл бұрын
когда сделает у себя квартиру похожую на чернобыльскую
@EdisonMusta04 жыл бұрын
Where can i buy it
@AlHarringtonsUAV4 жыл бұрын
bester-ltd.ru/product/antenna/ Best I could find. I'm better of making one as the means to buy this one isn't worth it in my opinion.
@vitcenek86114 жыл бұрын
Most of your projects are great, but this is fake as hell... Please avoid that, it did not makes a good name of your chanell.
@craigwall95364 жыл бұрын
It's not fake. This WWII technology, just at shorter wavelengths.
@johnhoye65843 жыл бұрын
I do not care if it works, this guy is awesome.
@proFFGaming23 жыл бұрын
I want to make this antenna please provide full details and diagram with materials that I need to built it
@bjornras4 жыл бұрын
Na Berlina! Towards Berlin - Sovjet WW2 retro with a homemade Yagi-Antenna and a green oldtimer .. But I like the curiosity though
@gunnarMyTube2 жыл бұрын
Recent war campaigns is hurting the connectedness between our peoples. Let’ s not allow this to affect the love between human beings.
@rexienamit5062 жыл бұрын
Diy Wi-Fi trap Version 2
@z3r0sz593 жыл бұрын
KREOSA Sou Do Brasil.. your videos are very good, the experiments or experience as I say, the antenna is very good. Would you manage to make an omni antenna 15Dbi or above 10Dbi ???
@Lorentz19753 жыл бұрын
The usb in the router where you plug in the wi fi adapter is the same usb for the storage (some modem routers have such functionality)
@NurdRage7774 жыл бұрын
Transmitters have a 250mw limit here so it won't work. The signal is too weak, it also forbidden to use any high end transmitter.
@krunov9629 Жыл бұрын
but its working well...i built one, check your theory again
@senseiDi5 ай бұрын
Epic. What is the max speed and bandwidth that this kind of antenna can handle?
@Chuggiek4 жыл бұрын
Sure i can pick up open networks with my own router.
@michaellands31224 жыл бұрын
Would it improve the antennas performance, if I made this antenna with all brass materials?. Brass threaded bolt?, Brass Nuts?, Brass Washers?, Brass Disks?. Would Steel materials work better?. Does the metal composition matter at all?. I would appreciate it if someone can answer in a comment. I'm just trying to figure out if Wi-Fi signals respond better, to certain types of metals.
@electricalmayhem4 жыл бұрын
Look at this here. ham.stackexchange.com/questions/1388/effect-of-different-metals-for-antenna-elements For the power levels of a wifi adapter I dont think you will see a noticable difference, especially not in the bolt or nuts. More important will be the precision of the element sizes and spacing, and say soldering the connections instead of relying on a friction fit.
@klaasj78084 жыл бұрын
maybe works in mother russia as they still have internet routers from 1973. but in the rest of the world you have modern routers which are already password protected from the factory. i dont see any free wifi anymore anywhere.
@zerolabs3 жыл бұрын
Looks like you use 75 ohm cable. Isn't the feedpoint impedance of the antenna 50 ohms?
@EzeePosseTV4 жыл бұрын
I have a USB WiFi adapter but it only has a built in (copper track on PCB) antenna. Could you do a video showing how to connect an external antenna to these types of wifi adapters.
@mtranchi4 жыл бұрын
am i the only one that loves that car?
@hubzcaps3 жыл бұрын
More rf expiriments like thiss. Please
@long-timelistenerfirst-t-us2yy4 жыл бұрын
*Great, now which button on your antennae will defeat the wifi password requirement?*
@LawsForever4 жыл бұрын
You will be astonished how many owners leave their WIFI unlocked! Just link into.
@nullbewahrer3 жыл бұрын
Hello Kreosan team, super job & super video, one question: I have build a similar UKW Yagi antenna several years ago and normally the second element (the one which you connect to the core of the coax cable) should be islolated against the whole boom assembly. I did not see any isolation materials for element two in your arrangement. Did you use a short piece of hose plus two plastic washers or something similar ....? Best regards
@tarendra82112 жыл бұрын
same question bro
@krunov9629 Жыл бұрын
no need for isolating..in fact if You do that performance will be degraded..check your antenna knowledge
@OldisGold-tp1xk4 жыл бұрын
Пожалуйста, предоставьте руководство по покупке вещей и простую карту Wi-Fi Gun
@gianpierverutti64433 жыл бұрын
Have you tried using a UTP cable ?... would have less cable atenuation
@saulhanson88013 жыл бұрын
These lads are geniuses
@Pilotkosinus Жыл бұрын
why u not test is with the normal antenna first. so we can see the diffrent?
@banexbanex76264 жыл бұрын
Greetings from Serbia, i made this antenna "v1" and it's work really,really good ,i think it's about 15 decibels,but this version have more than 20+. V1 is a more smaller than ralink grid of 20 db but very powerful
@rakun-raccoon19074 жыл бұрын
Ozbiljno, koliko si daleko uhvatio signal?
@andreibarbici26974 жыл бұрын
Can you answare at two questions ? 1. Why you don't use coaxial cable for 4G antenna like 50 Ohm. Or tell if it's more good to use coaxial TV cable ? 2. Why you never mentioned the lenght of the screw/bolt ?
@HelamanGile4 жыл бұрын
I would love to see you guys make a tincana and see how well it works against this
@anshukumarsingh954 жыл бұрын
I have came here after watching you guys on hacker om channel. Your collaboration with hacker om was awesome.