KTM 690 F5 fairing kit installation by RADE/GARAGE

See the step by step installation of the KTM 690 fairing kit from RADE/GARAGE. With this video guide you will install the kit in one afternoon.
More details on the kit:
www.radegarage...

[@maxflight777]

I’ve just ordered this for my 701. *I ordered at **21:00** one night, the next morning at **08:00** you said it had shipped!* Thank you, you sent tracking info too. I hope my skills are good enough for the install!

[@svantelindberg7058]

Great video on how to install the kit. It took me more than an afternoon to install but maybe I'm too careful to to make any mistakes. The only extra work I had to do was to grind a bit in the corners for the hole for the ABS-switch. For my KTM 690 enduro 2024 there is a USB-connector, this was not in the video but I figured out that anyways. The top carbon cover of the the tower has thinner wall thicknesss than the mask therefore the USB-connector is a bit loose in it's hole. I had som problem fitting all the cables, that took some time to figure out. Great product!

[@EleBation]

On you homepage you state that "The kit is fully bolted on and ready to plug and play. No drilling or permanent modifications. Whenever needed, you can simply reverse your bike back to the original setup" but still drilling is needed to fix the side panels in place and also some plastic cut (albeit not in a visible place). I personally wouldn't have a problem with that, but somebody might take it as a misleading advertising ;)

[@toniraff5488]

just put on the kit, everything worked perfectly :)

[@j0rdan9016]

With the washer you installed between the two clamps as a compression limiter. After installation is complete. Is there supposed to be play between the clamp and the neck of the frame?? I’ve watched this video repeatedly after completing my install and just wondering if that’s correct? Thanks for the great kit too 2024 KTM 690 🤙

[@thomasbinder5288]

Muss man die Schrauben wirklich nicht fest anziehen. Mit den Vibrationen der KTM oder Gas Gas lockern sich diese Schrauben sehr schnell oder nicht? Habe einen Tower von euch auf meiner KTM 690 R und verliere regelmäßig die Schrauben …..

[@shanabbas9207]

Good explanation❤

[@snyggstuffe]

Is the handle bar riser kit optional or is it necessary in order to make everything fit?

[@RADEGARAGE1]

Hi, the handlebar riser can be skipped, in case you don't intend to use the Scotts steering damper.

[@Sarj_ent]

I see this kit uses the older KTM rally fairing. Do you think I could use the newer rally fairing and make it fit with this kit? I really like your design with the carbon tower but I much prefer the look of the newer rally fairing.

[@RADEGARAGE1]

Hi, you can use white/orange sidepanels instead of gray/orange sidepanels. The white/orange version is for 2019-20, while MY21-23 have dark decals. The shape of sidepanels is identical, just let us know in your order which version you prefer.

[@timsalabimbombassa]

@@RADEGARAGE1 Is it possible to not mount the side panels? Is the screen stable enough with the 4 mounting points? I would prefer it like that for looks and maybe buffeting…

[@mhg_7330]

Top Video wie immer👍💪✌️

[@Hammy56]

I am installing the kit for my 2020 690…the brackets you show here at 27:30 I did not have in the box. Also I have the alternative blinkers but this video does not show how to install them.

[@RADEGARAGE1]

Hi Chris, these brackets is the update from only last week, as you ordered your kit earlier, you have the previous version with turn signals in the side fairings. There are yellow labels from inside indicating where to drill a hole.

[@Hammy56]

@@RADEGARAGE1 Thanks.

[@BlaKeJR1337]

Will it also fit the smcr?😮

[@juacartav3363]

I've seen various installations of the different versions of this kit on KTMs ans Huskys. I don't see why this kit wouldn't fit a SMCR.✌️