L293d motor driver arduino tutorial | DC motor control using arduino and l293d [CC]

In this video, we will learn how to interface L293D motor shield with Arduino. How a dc motor is controlled using Arduino and l293d. L 293d motor driver/shield using Arduino.With the help of this L293D motor shield, we can run 4 normal DC motors, 2 unipolar or bipolar stepper motors, and two Servo motors.
Buy electronics components, projects, modules, boards, sensors at best price. Visit:
www.dpvtechnol...
Link to download the library:
github.com/ada...
link to download code:
drive.google.c...
Video link to watch explanation of the code:
• code explanation of l2...
Our email address:
[e-mail]
Like our facebook page:
/ dpvtechnology
Subscribe us on youtube:
www.youtube.co...

[@Task_Force_141]

English accent is too good!!! 🔥👍

[@teerthraj_verma]

Thank you very much I worried a lot to use L293d motor driver with my project because of insuffient information of power supply But this video provides a great detail of different means of using power supply with this motor shield

[@BorisMiljkovic]

Great explanation. Thank you.

[@RASHiDALi143]

Dear I have a project with two motors one use for up and down and second is for left to right, for dish Receiver for Satellite Tracking.. may I use these modules???

[@joyalmj8720]

How many 12v Turbine gear motor can connected to motor shield ?

[@MrRobot007]

Very informative video bro....All done perfectly 🥰

[@Create_o_raptor]

Even with the jumper out.. when i supply 12 v to sheild .. arduino gets fried

[@pheakkdey2352]

Can we use this driver with esp32?

[@salsaamaliaputri-saphire-u7764]

which type of dc motor do u use?

[@sluxtpr1]

Thanks bro,, take your efforts. Very nice, very useful video for beginners.

[@OnlyFootball483]

luv u bro 🤰👸👸👸🤰🤰🤰🤰🤰🤰🤰🤰🤰🤰🤰♑

[@kulamanirout5766]

Sir can i use four 1000 rpm dc motors with 12v supply in this motor shield? With out facing the heating problem? Because sir i am using a L298N motor sheild but it was heating in 3 seconds like fire Please help can i use L293D instead of L298N?

[@reyanshniranjan9147]

Well yes you can! It supports 12v

[@Sakshwat_Mahajan]

thnks bro !! your video was of great help

[@ztiger09]

How many volts is your dc motor?

[@HirenNarkarRadhvanaj]

how to control 1 servo and 1 dc motor using l293d motor shield at same time. I watch many video on l293d shield but in all video different motor not run at same time . For example if there is a code for dc motor than you can run only 4 dc motor. If there is a code for servo motor you can run only 2 servo. But I want to run servo and dc motor together using l293d motor shield. So sir please provide me code for running two different motor ie..Servo and Dc motor same time.

[@bharathchandra2006]

can we use mg995 servo and 4 gear motors of 300 rpm to l293d shield?

[@jishabenny9183]

sir , but moters connected to diver moter shiled is not working, plz reply

[@Mariam-sf3re]

If I want to add joystick, how??

[@cecuenwu8842]

can we set the road back and forth 10 minutes forward 10 minutes. and set the speed

[@ulhasbetkikar2089]

Can i connect bluethhot module

[@kasemalrpe4106]

L293D engine hood problem. Output voltage in m4. 7 volts, and the rest of the outputs are 2 volts😢

[@sarveshmestry7501]

Can ardunio be given 12v 2amp Or only 5 to 9v supply

[@sarangalekamge1048]

Great, Thank you.

[@bolt_zz0]

bro I have connected all four motors to the motor driver shield but connected only 3.57 volt battery and the tyre is not moving is this a battery problem for my motor driver shield is not responding please help me

[@himalshad5530]

I think your supplied voltage is not enough.

[@reyanshniranjan9147]

Using the 9V battery is not good using a 3.7volt lithium ion battery in array of 2 is better

[@dsivateja7971]

bro it getting error in complation dc_motor_test.ino:23:6: error: 'void loop()' previously saying like that plzzz give me solution for it

[@harshavardhankanoj6021]

I have been trying to run 4 motors , but it's going to slow down at very faster with seperate 9v arduino powerup and external power supply of 12v , can you please help me. motor power supply range 3v-6v

[@HirenNarkarRadhvanaj]

Sir when I tried to compile code it shows message (FATTAL ERROR AFmotor.h) nosuch file or library .what is reason?.

[@sujalkumar3140]

Yes I'm also facing this problem

[@a2zcreator109]

af motor library install karna padta h

[@arindammoitra3443]

How I connect HM-10 Bluetooth module when using this L293d arduino motorsheld?

[@premsaisiddi24680]

Bro till how much mah battery we can plug to motor driver shield bro can I use 4.2 v 6000 mah battery of 2psc is the motors works good bro plz give me a solution bro plzz

[@hrkalita159]

Is L293D fits with ardrino uno Atmega 328p

[@thoughtsofrz8587]

Super

[@ashpjangde]

Thanks man!!

[@vikrantsingh47]

can i connect 4 dc motors and one servo? if not, then can i connect 4 dc motors in two slots (m1 and m2), and one servo, as i am making a 4 wheel car

[@SK_Senthil]

Recommended battery to connect 4 BO Motor with L293D ? I am having 2 numbers of 18650 battery as of now!

[@AlessandroBoggiano]

If I would use two servos and I give power to Arduino with the USB, can I use a battery pack to power the servos ?

[@filipchorbadjian7952]

How can I connect a bluetooth module on this device? I want to power it using bluetooth. Thanks

[@VanshSharma-mo7gu]

Just Connect rx and tx Pin to Pin no. 1 and 0 respectively and Power you can supply with the servo Gnd and positive pins

[@jbrown5389]

Can you do a video showing how to control 4 motors via Bluetooth??

[@granger5994]

Help me , why my obstacle avoiding car not motor not working ?

[@mdahossain1665]

what is the model of this dc motor ?

[@muhammadkhurram633]

thank you so much

[@aarifkhatri8501]

How cost

[@maximusdesimus1943]

Did anybody else worry he was going to fry something on the shield when he was sweeping the 9V leads across it?

[@adilabusafa]

أهلاً وسهلاً ومرحباً بك-يتعذر الاشتراك ولا يوجد جرس-يتعذر الاستجابة لكل طلباتك-شكراً لك-يتعذر التعليق- لا أعلم .

[@nilotpaulkundu7487]

can i run the motor using digitalwrite ?/

[@wasantnage4542]

Sir , motor driver shield me motor laganese L293D IC heat kyu hota hai

[@a2zcreator109]

mera bhi hota h

[@JayPatel-mg8dm]

thanks bro

[@haolekegs696]

does this code allow for turning?

[@MohammadAlshahrani]

The library that your mintioned is old

[@mansoorisrar9707]

Me ek project bna raha hn kia ap meri us me help kr skte hen...

[@harshitjajoria9076]

Why the speed of the motor is slow ?

[@vlektor]

search for the needed voltage for your dc motor and use a power supply with that voltage to power the driver shield

[@johnlobo5635]

Boa tarde amigo daria apaixonar um motor Brushless porque nunca vi ninguém acionando neste motor

[@ThriveMindAndBody]

are u assamese??

[@AbhishekGupta-wb8co]

Can this library will be compatible with arduino mega?

[@DPVTECHNOLOGY]

yes

[@khorzhanchuan8375]

Can this used on IOT?

[@SamSam-qc9kn]

Can we make flying drone using this sir

[@DPVTECHNOLOGY]

no, you have to use BLDC motor

[@SamSam-qc9kn]

sir i mean...can we use this board for making drones

[@shuaibahmed4580]

Can I connect 4 dc motor and 1sevo at one time

[@DPVTECHNOLOGY]

yes

[@nikhilpajayan3131]

thankyou

[@kingdavid4463]

Hi, does anyone know if I can use 4 DC motors and 1 SERVO motor at the same time? Thank you for answering

[@VanshSharma-mo7gu]

Yes you can

[@johnlobo5635]

Boa tarde amigo daria para acionar o Children Como esc para acionar motor brushless bifásico ou sejá três fios.

[@havefun8962]

Hi, if i use 8 motor. And the output of L293d is only 4. Can i put 2 motor in 1 output? Event it run at same time..

[@extras6604]

Yes bro, It works. I tried only when 3 batteries in parallel( parallel con adds current) for me. I used 9v battery

[@laytonpratt]

When I unplug it from the computer it stops working.

[@surajnayakraghuvanshi2495]

I

[@electrobot8468]

Can I use it with other litter T,L

[@ulhasbetkikar2089]

😮

[@mahadevappabadiger4291]

Video no t claer

[@ulhasbetkikar2089]

😂

[@mirudhulabalasubramani1735]

thank u very much

[@muhamadshahiran5347]

Can i connect 2 dc motor and 2 stepper motor?

[@wasantnage4542]

Sir , motor driver shield me motor laganese L293D IC heat kyu hota hai