A small vid on how I check my injectors. Forgot to caption the leaktest of the injector tips.
Пікірлер: 31
@johnfry90106 жыл бұрын
Nice , first time I have seen anyone work on injectors .
@JanDootjes6 жыл бұрын
Thanks you John, good to hear!
@servihomestead43244 жыл бұрын
Very informative. The injectors look almost identical to the ones on my old Farmall 706 tractor. I like the idea of spinning the needle in the nozzle using a drill. Thanks for sharing.
@amabeza5 жыл бұрын
Appreciate your work
@kenhorton76504 жыл бұрын
As a retired employee of what was a Simms service depot full marks for getting them to work. A couple of comments, do take the pressure spring setting down to nil before trying to remove the nozzle retaining nut because if not the nozzle can turn with the nut and you can shear the two dowels off in the injector body and ruin the assembly. The full repair would be by internally recutting the nozzle seat and the needle face to different prescribed angles for which you need a bit of special equipment and you may have noticed there is an auxiliary spray from the nozzle for starting purposes, this needs unblocking in most cases which is very difficult, the needle valve freeing off has to be done carefully without the use of any abrasives as too free a fit and there would be an excess of fuel leaking back in the injector and not injected into the engine, all this can be measured on the hand tester. This nozzle was just about the most difficult and time-consuming type to refurbish to spray properly and on cost was frequently replaced with a new one. The test pump can test most types of injectors, but spray into an enclosed container for safety reasons or at least guard it, and most important keep away from any naked flame, and don't try that as it is very dangerous!
@gerrygorman2734 жыл бұрын
Ken have you ever refurbed the tdv8 Injectors, I had a chap take mine out to remove my inlet manifold and now they wont fire, loud rattly noise from them
@kenhorton76504 жыл бұрын
@@gerrygorman273 I have no idea even what a tdv8 injector looks like ! what engine ? I may find an answer if I could see one as the earleir types all worked much the same way.could you post a photo of one ? Ken
@rovertasmania70336 жыл бұрын
Fantastic, just hat i was looking for.
@ROVITTv4 жыл бұрын
Thanks for sharing this video
@jonathanjaram38576 жыл бұрын
Hola! Muchas gracias por compartir... excelente video! Una pregunta: ¿El inyector se abre a 2000 ó a 2100 psi? Y ¿a cuántas psi se cierra? Otra pregunta: ¿sólo se puede ajustar los psi de apertura ó también se puede ajustar el cierre? te agradezco el tiempo que tomaste para hacer el video!
@andraxx95894 жыл бұрын
Hello, open pressure is 135bar (2000psi). You can only adjust the opening pressure
@rjtecheng5 жыл бұрын
What type of test pump would I need to test the same type of CAV injectors from a 2.25 Landrover diesel ?
@ryancamilleri94733 жыл бұрын
Hi is the pressure the same for bmc 1500 ? Thank you
@AL-oe6ge4 жыл бұрын
Did you lap both the nozzle and the injector body? How do you lap it with the alignment dowels in or did you remove them?
@JanDootjes4 жыл бұрын
If you need to lap the injector body surface, you first need to remove the dowels indeed. I didn't take them out in this case. - Jan
@sumanmondalsuman76353 жыл бұрын
Thanks sir 👍👍👍
@jpmalette64276 жыл бұрын
Very interesting, which engines uses these injectors?
@JanDootjes6 жыл бұрын
Thanks JP, Those 'C.A.V. Pintaux' injectors came out of an 2.25 litre Rover diesel engine. There quite commonly used in older diesel engines.
@alexanderrosales76754 жыл бұрын
Your spray pattern is way off, you need new injector nozzles.
@Henning_S. Жыл бұрын
Yes, the spray pattern is really bad
@greenwolf87325 жыл бұрын
Gracias... 👍
@rebwarhussen89682 жыл бұрын
ديفندر ۱۱۰ دیزل
@rajeevadesilva79516 жыл бұрын
thanks mate you saved my day
@JuanMiguelGarcia19694 жыл бұрын
Very good job 👏👏👏👍❤️
@madinadiesellab4 жыл бұрын
No good setting. Injectors falt
@armandh92873 жыл бұрын
Very nice video! Thank you.
@gerrygorman2734 жыл бұрын
Great vid, can the TDV8 injectors be overhauled, how to do tell if one is bad, do the knock or tick, mine are knocking on startup
@JanDootjes4 жыл бұрын
I never overhauled the injectors which you mentioned, so don't know about that. A injector normally doesn't create sound. Most likely the knocking noise comes from your valve clearance.
@solorip5 жыл бұрын
Nice job I'm going to make a tester with an old jack
@mattluszczak65675 жыл бұрын
You can buy one from ebay or from mercedes source website