Laser Duct Fan Upgrade | AC Infinity A6

In this video I will be upgrading my Vivosun 195 CFM to a AC Infinity A6 352 CFM for my Roly LaserMatic MK2 and Hoatian 60 watt Mopa Fiber Laser. All links below.Please Like Subscribe and share.Ring that bell to be notified the next time i post or go live.
Affiliate Link “As an Amazon Associate I earn from qualifying purchases.”
Amazon USA
AC Infinity CLOUDLINE A6, Quiet 6” Inline Duct Fan
amzn.to/42HHGRp
AC Infinity Flexible 4-Inch Aluminum Ducting
amzn.to/3T0ArRk
POWERTEC 70295-P2 4-Inch Integrated Blast Gate
amzn.to/3uJEd85
Premium Silver Aluminum Foil Tape
amzn.to/3OL3wgP
www.printables...
Contact Pascal Liu
Use code 3DHP100 to get 100.00 one of there Fiber Lasers
htlasercnc.en....
haotianlasercn...
/ @lsengraving
l.facebook.com...
/ @lsengraving
/ @htlholsters6867
If you use this link to purchase your LaserMatic I will receive a small commission.
rolyautomation...?bg_ref=ScNstGMBo0
Affiliate Link “As an Amazon Associate I earn from qualifying purchases."
amzn.to/3SxBNm2
amzn.to/46JkrY7
amzn.to/472dQrx
Amazon Affiliate link for this Amazing Laser Roly LaserMatic10
amzn.to/3Ju7TKN
rolyautomation...
/ @thelouisianahobbyguy
/ @lasermakersrealm
/ @lsengraving
/ @hobowithwood
Affiliate link Scratch paper
amzn.to/3JnHLRO
Affiliate link Basswood
amzn.to/42PdoKQ
Affiliate Link to th3d studio. Enter this code at checkout for 5% off your Order
Use code 3DHP5
www.th3dstudio...
/ 2340130806200088
/ jerry3dhp
/ 1859793054033450
If you would Like to Print out my LOGO. www.thingivers...
1 Time donations Welcome at Paypal.com paypal.me/JERR...
Guys Receive 15% off your orders with code 3DHP. Except for Special Filament Packs.
Here is a link to ZYLTECH Web Site .Starting Sept 1st only 5% Off Going Forward..
www.zyltech.com/
www.buymeacoff...
Link to my ETSY Store www.etsy.com/s...
Affiliate Link to Creality 3D
www.creality3d...?sca_ref=329220.Za35SVgWJ5
SUNLU 10% off discount for: 1. Printer S8 2. One KG printer filament 3. 3D print pen
www.sunlu.com?sca_ref=347524.zxwYGHFozp
www.th3dstudio...
Guys and Gals. I got some Cool SWAG Here.
teespring.com/...
/ 499445360414611
/ 3dprintinga. .
/ jerryeknapp
Checkout my page at 3dhp.net/
Try Amazon Prime 30-Day Free Trial
amzn.to/304BKUk
Affiliate Link “As an Amazon Associate I earn from qualifying purchases.”
Amazon USA
Copyright Free Music from Track Tribe Big 10

[@mgl_angel0542]

Great System set up! 🫡

[@mikedoyle5362]

Really like the ac infinity. I use the 6in hose up until the last 5 in and have a reducer for 6 to 4.

[@mikedoyle5362]

Great start! Always good to have a laugh!

[@pcvanvliet]

Looking good Jerry, good airquality is important in your makerspace when you spend a lot of time there.

[@LSEngraving]

Looking good Jerry as always I love that unboxing knife

[@KRich408]

I might upgrade the Hon&Guan 130 CFM it's Junk for my Roly 20w , I just etched a bunch of mirrors today. my basement smells like a plastic factory.

[@3DHP]

Well that's no good.You don't want to be breathing in anything that might have harmful chemicals in it.

[@chrislmink]

Make sure you keep that back door locked if you have a waste gate open it sticks out past the door when open lol. I didnt think it was that loud at all.

[@3DHP]

It easily turns at the Y. Thought about when I screwed to the wall.Louder than the smaller one,but ok.

[@TheLouisianaHobbyGuy]

I had one of these, and it seemed the only settings that worked were the last two. Should just be High/Low.

[@KRich408]

I just purchased this fan its great! 👍 im still trying to figure out how to remove the factory fan without cutting the wires or damage the condit or orange plastic? The fans cord won't fit through the Condit Roly used.

[@3DHP]

Unclip the fan,the wire is like 6 inches long.Do not remove the silver metal duct.The wire and connector will slide through it.Then use shorter bolts for duct with grate. Save fan and screws,if you ever sell it,you can put back to stock.

[@KRich408]

@@3DHP ok thanks 👍👍👍👍👍

[@mikedoyle5362]

Do you use a window to vent

[@3DHP]

lol,,you didn't watch the video.

[@BLUEMOONENTERPRISES]

When you removed the fan, were you able to continue to use the same exit fitting minus the fan to attach the hose? Was it difficult to remove the fan? My Lasermatic should arrive soon and I'm trying to sort out an exhaust for it, which is going to be very similar to yours. Thanks.

[@3DHP]

I just used shorter bolts and put the duct back on. Once you unplug fan,wire with connector will slide out of the aluminum channel,no reason to try and pry it off.Its very easy to do.I also left the fan screen on the inside.

[@BLUEMOONENTERPRISES]

@@3DHP Thanks! Great explanation!